• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05a
• /
• pp.349-354
• /
• 1996

SACOM(Simulation Analyser with Cognitive Operator Model) is being developed at Korea Atomic Energy Research Institute to simulate human operator's cognitive characteristics during the emergency situations of nuclear power plans. An operator model with error mechanisms has been developed and combined into SACOM to simulate human operator's cognitive information process based on the Rasmussen's decision ladder model. The operational logic for five different cognitive activities (Agents), operator's attentional control (Controller), short-term memory (Blackboard), and long-term memory (Knowledge Base) have been developed and implemented on blackboard architecture. A trial simulation with a scenario for emergency operation has been performed to verify the operational logic. It was found that the operator model with error mechanisms is suitable for the simulation of operator's cognitive behavior in emergency situation.

• Advances in nano research
• /
• v.11 no.6
• /
• pp.641-648
• /
• 2021

In this article, the dynamic parameters (frequencies, mode shapes, damping ratios) of the scaled concrete structure and the dynamic parameters (frequencies, mode shapes, damping ratios) of the entire outer surface of titanium dioxide, 80 micron in thickness are compared using operational modal analysis method. Ambient excitation was provided from micro tremor ambient vibration data on ground level. Enhanced Frequency Domain Decomposition (EFDD) was used for the output only modal identification. From this study, a good correlation between mode shapes was found. Titanium dioxide applied to the entire outer surface of the scaled concrete structure has an average of 11.78% difference in frequency values and 10.15% in damping ratios, proving that nanomaterials can be used to increase rigidity in structures, in other words, for reinforcement. Another important result determined in the study was the observation of the adherence of titanium dioxide and similar nanomaterials mentioned in the introduction to concrete structure surfaces was at the highest level.

• Advances in nano research
• /
• v.12 no.1
• /
• pp.65-72
• /
• 2022

The dynamic properties (frequencies, mode shapes, damping ratios) of the scaled WPC warehouse are compared using the operational modal analysis approach to the dynamic parameters (frequencies, mode shapes, damping ratios) of the full outer surface of titanium dioxide, 70 micron in thickness. Micro tremor ambient vibration data on ground level was used to provide ambient excitation. For the output-only modal identification, Enhanced Frequency Domain Decomposition (EFDD) was used. This study discovered a strong correlation between mode shapes. Titanium dioxide applied to the entire outer surface of the scaled WPC warehouse results in an average 14.05 percent difference in frequency values and 7.61 percent difference in damping ratios, demonstrating that nanomaterials can be used to increase rigidity in structures, or for reinforcement. Another significant finding in the study was the highest level of adherence of titanium dioxide and similar nanomaterials mentioned in the introduction to WPC structure surfaces.

• Journal of Korean Society for Quality Management
• /
• v.43 no.1
• /
• pp.67-84
• /
• 2015

Purpose: By analyzing what kind of organizational reaction is shown by employees to corporate social responsibility (CSR), I want to propose a plan to maximize achievement(organizational commitment and productive behavior) within corporation. Methods: Regression analysis is used to analyze relationship between CSR awareness and achievement within corporation. Then structural equation model is used to check control effect of corporate member's participation in CSR. Results: It is proved that employee's CSR awareness has positive relationship with organizational commitment and productive behavior. It is shown that when employees have participated in CSR programs directly, effectiveness of relationship was especially higher for Organizational Citizenship Behavior (OCB) and innovative behavior. Conclusion: In order to increase organizational commitment and productive behavior of employees, corporation's social responsibility management, in other words ethical management must be used so their motivation can be increased and so they can directly participate in CSR programs which will increase effectiveness of organization.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2000.04a
• /
• pp.6-6
• /
• 2000

On-orbit thermal behavior of KOMPSAT (Korea Multi-purpose Satellite) propulsion system employing hydrazine (N$_2$H$_4$) liquid monopropellant is addressed. Thermal control performance to prevent propellant freezing in spacecraft-operational orbit was verified by flight telemetry data obtained during LEOP (Launch and Early Operation Phase). Results are depicted in terms of temperature history during several orbits selected and are compared with acceptable temperature ranges of system components. Cyclic behavior of temperature is reduced into duty cycles of the avionics heaters and subsequently converted into the electrical power required to keep away from propellant freezing. Temperature of each component which was achieved under on-ground thermal-balanced condition of spacecraft, is presented for comparison with the flight data, additionally.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.25 no.3
• /
• pp.61-67
• /
• 2017

The Nose Landing Gear(NLG) of Rotary Wing Aircraft is an essential equipment in Landing System for pilot to perform a flight mission. It supports the fuselage at ground and absorbs the impact from the ground when landing, thereby, these functions sustain operational capability for pilot and crew. However, the A aircraft caused stick-slip behavior when it was stationed on the ground. Therefore, this paper summarizes pilot comment in operation which are classified by cause of occurrence and the troubleshooting process about each comment. It also describes design improvements which was derived from troubleshooting and suggests verification results of flight test.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1215-1220
• /
• 2008

The aim of this paper is to perform a finite element analysis that will have the ability to predict the seal performance characteristics, such as deformation, contact load and friction and also is to provide a means of potential seal designs, which can reduce the time and cost of designing the performance of the seal. The material property tests of elastomer seal are performed to obtain the hyperelastic properties and The Mooney-Rivlin constants are determined from these test results. A 2D modelling of the seal cross section is performed to simulate the contact behavior between the seal on the piston and the cylinder bore under operation conditions. The deformation behavior, contact load and friction of an elastomer seal is analyzed by a finite element method which performs three analytic phases of interference fit, the variations of pneumatic pressure and piston movement under the operational conditions.

• Journal of Ocean Engineering and Technology
• /
• v.14 no.2
• /
• pp.28-35
• /
• 2000

In this paper a complicated structural behavior in collision and its effect of energy transmission to the collision bulkhead was examined through a methodology of the numerical simulation to obtain a ideal bow construction and a location of collision bulkhead against heat on collision. At present the bow structure is normally designed in consideration of its specific structural arrangement and internal and external loads in these areas such as hydrostatic and dynamic pressure wave impact and bottom slamming in accordance with the Classification rules and the specific location of collision bulkhead by SOLAS requirement. By these studies the behavior of the bow collapse due to collision was synthetically evaluated for the different size of tankers and its operational speed limits and by the results of these simulation it provides the optimal design concept for the bow construction to prevent the subsequent plastic deformation onto or near to the collision bulkhead boundary and to determine the rational location of collision bulkhead.

• Journal of Korean Port Research
• /
• v.14 no.2
• /
• pp.219-231
• /
• 2000

In this paper a complicated structural behavior in collision and its effects of energy translation to the collision bulkhead was examined through a methodology of the numerical simulation to obtain a ideal bow construction and a location of collision bulkhead against head on collision. In the present the bow structure is normally designed in consideration of its specific structural arrangements and internal and external loads in these area such as hydrostatic and dynamic pressure, wave impact and bottom slamming in accordance with the Classification rules, and the specific location of collision bulkhead by SOLAS requirement. By these studies the behavior of the bow collapse due to collision was synthetically evaluated for the different size of tankers and its operational speed limits, and by the results of these simulation it provides the optimal design concept for the bow construction to prevent the subsequent plastic deformation onto or near to the collision bulkhead boundary and to determine the rational location of collision bulkhead.

• Toxicological Research
• /
• v.25 no.1
• /
• pp.9-15
• /
• 2009

Historically, research in toxicology has utilized non-human mammalian species, particularly rats and mice, to study in vivo the effects of toxic exposure on physiology and behavior. However, ethical considerations and the overwhelming increase in the number of chemicals to be screened has led to a shift away from in vivo work. The decline in in vivo experimentation has been accompanied by an increase in alternative methods for detecting and predicting detrimental effects: in vitro experimentation and in silico modeling. Yet, these new methodologies can not replace the need for in vivo work on animal physiology and behavior. The development of new, non-mammalian model systems shows great promise in restoring our ability to use behavioral endpoints in toxicological testing. Of these systems, the zebrafish, Danio rerio, is the model organism for which we are accumulating enough knowledge in vivo, in vitro, and in silico to enable us to develop a comprehensive, high-throughput toxicology screening system.