• Journal of the Society of Naval Architects of Korea
• /
• v.52 no.4
• /
• pp.323-329
• /
• 2015

For the design guide of a vessel operating in cold region, numerical analysis was carried out to evaluate the ice class louver which installed the heating cables by using ANSYS 13.0 CFX. The numerical analysis was performed by considering Unsteady Reynolds Averaged Navier Stokes (RANS) equation. This study based on the experimental results of ‘The Cryogenic Performance Evaluation for the Excellent De-icing Ice Class Louver’ in KRISO. For validation of the numerical analysis results, the cold chamber experimental data measured by the heat sensors in certain location of the ice class louver was used. The external environmental temperature which varies from 0℃ to –30℃ was considered in numerical analysis. Also the design guide for optimum de-icing presented through heating cable power capacity(33 W/m, 45 W/m, 66 W/m), location of the heating cable(front, center, behind on the blade) and relative velocity(1 m/s, 4 m/s, 7 m/s).

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.15 no.2
• /
• pp.58-63
• /
• 2019

This paper presents preliminary analysis and results on IASCC sensitivity of a core shroud in the reactor pressure vessel. First, neutron irradiation flux distribution of the reactor internals was calculated by using the Monte Carlo simulation code, MCNP6.1 and the nuclear data library, ENDF/B-VII.1. Second, based on the neutron irradiation flux distribution, temperature and stress distributions of the core shroud during normal operation were determined by performing finite element analysis using the commercial finite element analysis program, ABAQUS, considering irradiation aging-related degradation mechanisms. Last, IASCC sensitivity of the core shroud was assessed by using the IASCC sensitivity definition of EPRI MRP-211 and the finite element analysis results. As a result of the preliminary analysis, it was found that the point at which the maximum IASCC sensitivity is derived varies over operating time, initially moving from the shroud plate located in the center of the core to the top shroud plate-ring connection brace over operating time. In addition, it was concluded that IASCC will not occur on the core shroud even after 60 years of operation (40EFPYs) because the maximum IASCC sensitivity is less than 0.5.

• Industrial Engineering and Management Systems
• /
• v.15 no.3
• /
• pp.278-288
• /
• 2016

Automation ensures accurate and well-organized container transportation in container terminals. This paper addresses operational issues such as equipment scheduling and the coordination between various pieces of equipment in a rail-based automated container terminal. Containers are relayed using multiple types of equipment from road trucks to a vessel and vice versa. Therefore, handshaking is required during a container transfer between different pieces of equipment. Synchronization between the schedules of all the equipment is important to reduce equipment waiting times and the time required for transporting containers, which results in a short turnaround time for a vessel. This paper proposes an integrated control system with the objective of synchronizing the operations of different types of equipment, provides a list of decisions to be made by the control module of each type of equipment, and shows all the required information transfers between control modules. A scheme for the integrated scheduling of multiple types of equipment is proposed. The decisions made by each control module in a real-time fashion are listed with detailed explanations, and the information transfer between managers in a real-time situation at the proposed terminal is described.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.12 no.1
• /
• pp.48-59
• /
• 2020

A traditional propeller can easily become entangled with floating objects while operating. In this paper, we present a newly developed Electromagnetic-valve-control-based Water-jet Propulsion System (ECWPS) for an unmanned surface cleaning vessel that can be flexibly controlled via a Micro Control Unit (MCU). The double-structure was adapted to the unmanned surface cleaning vessel for floating-collection missions. Computational Fluid Dynamics (CFD) software for operating effect simulation was also used to reveal the working principle of the ECWPS under different conditions. Neglecting the assembly technique, the design level, controlling strategy, and maneuvering performance of the ECWPS reached unprecedented levels. The ECWPS mainly consists of an Electromagnetic-valve Array (EA), pipeline network, control system, and water-jet source. Both CFD analyses and experimental results show that the hydraulic characteristic of the ECWPS was predicted reasonably, which has enormous practical value and development prospects.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.48 no.4
• /
• pp.337-345
• /
• 2012

One of representative Korean fisheries, jigging and angling has 5,700 vessels for squid and hairtail. Hairtail angling is the most typical fishery in Jeju and has an enormous impact on regional economy. However, the price hike in oil and labor costs triggered the necessity of developing a high efficient and energy saving fish luring lamp in recent times. For that reason, this study aimed to analyze the fishing performance of the aircooled LED lamp targeting hairtail angling fishery. The experiment was conducted from September through October in 2009-2011 for a 9.77 ton of fishing vessel setting up 100 lamps. The fishing performance was tested compared with 6 vessels using metal halide lamps in the same waters. As the LED lamp's performance goes up, different lamps were used in 2008 for 80W, 2009 for 120W and 2011 for 180W respectively. The catch and CPUE of the experimental vessel have gradually increased respectively taking the $4^{th}$ and $6^{th}$ place in 2009, the $4^{th}$ and $2^{nd}$ place in 2010, the $1^{st}$ and $1^{st}$ place in 2011 among the 7 vessels. In summary, the LED fishing lamp showed higher fishing performance than comparison groups. It saved 33% of oil consumption and cut down on operating expenses and greenhouse gases emission.

• Korean Chemical Engineering Research
• /
• v.58 no.3
• /
• pp.493-497
• /
• 2020

Hazardous area classification is designed to prevent chemical plant explosions in advance. Generally, the duration of the explosive atmosphere is used for zone type classification. Herein, IEC code, a quantitative zone type classification methodology, was used to achieve Zone 2 NE, which indicates a practical non-explosion condition. This study analyzed the operating pressure of a vessel handling propane to achieve Zone 2 NE by applying the IEC code via MATLAB. The resulting zone type and hazardous area grades were compared with the results from other design standards, namely API and EI codes. According to the IEC code, the operating pressure of vessels handling propane should be between 101325-116560.59 Pa. In contrast, the zone type classification criteria used by API and EI codes are abstract. Therefore, since these codes could interpret excessively explosive atmospheres, care is required while using them for hazardous area classification design.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.1
• /
• pp.141-152
• /
• 2022

As interest increases related to the development of eco-friendly energy, the offshore wind turbine market is growing at an increasing rate every year. In line with this, the demand for an installation vessel with large scaled capacity is also increasing rapidly. The wind turbine installation vessel (WTIV) is a fixed penetration of the spudcan in the sea-bed to install the wind turbine. At this time, a review of the spudcan is an important issue regarding structural safety in the entire structure system. In the study, we analyzed the current procedure suggested by classification of societies and new procedures reflect the new loading scenarios based on reasonable operating conditions; which is also verified through FE-analysis. The current procedure shows that the maximum stress is less than the allowable criteria because it does not consider the effect of the sea-bed slope, the leg bending moment, and the spudcan shape. However, results of some load conditions as defined by the new procedure confirm that it is necessary to reinforce the structure to required levels under actual pre-load conditions. Therefore, the new procedure considers additional actual operating conditions and the possible problems were verified through detailed FE-analysis.

• Journal of Navigation and Port Research
• /
• v.38 no.6
• /
• pp.567-575
• /
• 2014

In recent times, an obvious strategy in liner shipping markets that has come to the fore is slow steaming. Nowadays, most liner shipping companies have decelerated the voyage speed to 15-18 knots on major routes, and some leading liner shipping companies have a plan to reduce it to below 15 knots. Slow steaming is helpful in reducing the operating cost and the amount of greenhouse-gas emissions on a single vessel with lower fuel consumption. However, it also creates various negative effects such as the opportunity cost, additional fixed costs and an in-transit inventory cost on a loop. Hence, the net operating cost on a loop is changing dynamically due to the changes of voyage speed based on various slow steaming effects. The aim of this study is to analyze the slow steaming effects in the liner shipping, and to find the best voyage speed that minimizes the operating cost on a loop. Moreover, this study suggests the recommendable strategy for liner shipping companies. To achieve the aim of this study, a simulation model has been designed using System Dynamics.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.6 no.2
• /
• pp.442-458
• /
• 2014

Wave induced vibrations increase the fatigue and extreme loading, but this is normally neglected in design. The industry view on this is changing. Wave induced vibrations are often divided into springing and whipping, and their relative contribution to fatigue and extreme loading varies depending on ship design. When it comes to displacement vessels, the contribution from whipping on fatigue and extreme loading is particularly high for certain container vessels. A large modern design container vessel with high bow flare angle and high service speed has been considered. The container vessel was equipped with a hull monitoring system from a recognized supplier of HMON systems. The vessel has been operating between Asia and Europe for a few years and valuable data has been collected. Also model tests have been carried out of this vessel to investigate fatigue and extreme loading, but model tests are often limited to head seas. For the full scale measurements, the correlation between stress data and wind data has been investigated. The wave and vibration damage are shown versus heading and Beaufort strength to indicate general trends. The wind data has also been compared to North Atlantic design environment. Even though it has been shown that the encountered wind data has been much less severe than in North Atlantic, the extreme loading defined by IACS URS11 is significantly exceeded when whipping is included. If whipping may contribute to collapse, then proper seamanship may be useful in order to limit the extreme loading. The vibration damage is also observed to be high from head to beam seas, and even present in stern seas, but fatigue damage in general is low on this East Asia to Europe trade.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.2
• /
• pp.179-184
• /
• 2009

The Fuel Test Loop(FTL) which is capable of an irradiation testing under a similar operating condition to those of PWR(Pressurized Water Reactor) and CANDU(CANadian Deuterium Uranium reactor) nuclear power plants has been developed and installed in HANARO, KAERI(Korea Atomic Energy Research Institute). It consists of In-Pile Section(IPS) and Out-of Pile System(OPS). The IPS, which is located inside the pool is divided into 3-parts; the in-pool pipes, the IVA(IPS Vessel Assembly) and the support structures. The test fuel is loaded inside a double wall, inner pressure vessel and outer pressure vessel, to keep the functionality of the reactor coolant pressure boundary. The IVA is manufactured by local company and the functional test and verification were done through pressure drop, vibration, hydraulic and leakage tests. The brazing technique for the instrument lines has been checked for its functionality and performance. An IVA has been manufactured by local technique and have finally tested under high temperature and high pressure. The IVA and piping did not experience leakage, as we have checked the piping, flanges, assembly parts. We have obtained good data during the three cycle test which includes a pressure test, pressure and temperature cycling, and constant temperature.