• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2004년도 Proceedings of ISRS 2004
• /
• pp.512-514
• /
• 2004

The Electro-Optical Camera (EOC) is a high spatial resolution, visible imaging sensor which collects visible image data of the earth's sunlit surface and is the primary payload on KOMPSAT-l. The purpose of the EOC payload is to provide high resolution visible imagery data to support cartography of the Korean Peninsula. The EOC is a push broom-scanned sensor which incorporates a single nadir looking telescope. At the nominal altitude of 685Km with the spacecraft in a nadir pointing attitude, the EOC collects data with a ground sample distance of approximately 6.6 meters and a swath width of around 17Km. The EOC is designed to operate with a duty cycle of up to 2 minutes (contiguous) per orbit over the mission lifetime of 3 years with the functions of programmable gain/offset. The EOC has no pointing mechanism of its own. EOC pointing is accomplished by right and left rolling of the spacecraft, as needed. Under nominal operating conditions, the spacecraft can be rolled to an angle in the range from +/- 15 to 30 degrees to support the collection of stereo data. In this paper, the status of EOC such as temperature, dark calibration, cover operation and thermal control is checked and analyzed by continuously monitored state of health (SOH) data and image data during the mission life of 3 years. The aliveness of EOC and operation continuation beyond mission life is confirmed by the results of the analysis.

• 한국환경과학회지
• /
• 제11권8호
• /
• pp.819-827
• /
• 2002

Laboratory scale experiments were conducted to evaluate the performance of a biofilter for eliminating dimethyl sulfide(DMS). A commercial compost/pine bark nugget mixture served as the biofilter material for the experiments. The gas flow rate and DMS concentration entering the filter were varied to study their effect on the biofilter efficiency. The operating parameters, such as the residence time, inlet concentration, pH, water content, and temperature, were all monitored throughout the filter operation. The kinetic dependence of the DMS removal along the column length was also studied to obtain a quantitative description of the DMS elimination. High DMS removal efficiencies(>95％) were obtained using the compost filter material seeded with activated sludge. DMS pollutant loading rates of up to 5.2 and 5.5 g-DMS/m$^3$/hr were effectively handled by the upflow and downflow biofilter columns, respectively. The macrokinetics of the DMS removal were found to be fractional-order diffusion-limited over the 9 to 25 ppm range of inlet concentrations tested. The upflow column had an average macrokinetic coefficient(K$\_$f/) of 0.0789 $\pm$ 0.0178 ppm$\^$$\sfrac{1}{2}$//sec, while the downflow column had an average coefficient of 0.0935 $\pm$ 0.0200 ppm$\^$$\sfrac{1}{2}$//sec. Shorter residence times resulted in a lower mass transfer of the pollutant from the gas phase to the aqueous liquid phase, thereby decreasing the efficiency.

• 대한기계학회논문집B
• /
• 제25권6호
• /
• pp.799-803
• /
• 2001

Miniature heat pipe(MHP) with woven-wired wick was used to cool the CPU of a notebook PC. The pipe with circular cross-section was pressed and bent for packaging the MHP into a notebook PC with very limited compact packaging space. A cross-sectional area of the pipe is reduced about 30% as the MHP with 4mm diameter is pressed to 2mm thickness. In the present study a performance test has been performed in order to review varying of operating performance according to pressed thickness variation and heat dissipation capacity of MHP cooling module that is packaged on a notebook PC. New wick type was considered for overcoming low heat transfer limit when MHP is pressed to thin-plate. The limiting thickness or pressing is shown to be within the range of 2mm∼2.5mm through the performance test with varying the pressing thickness. When the wall thickness of 0.4mm is reduced to 0.25mm for minimizing conductive thermal resistance through the wall of heat pipe, heat transfer limit and thermal resistance of MHP were improved about 10%. In the meantime, it is shown that the thermal resistance and heat transfer limit for the MHP with central wick type are higher than those of MHP with existing wick types. The results of performance test for MHP cooling modules with woven-wired wick to cool a notebook PC shows the stability as cooling system since T(sub)j(Temperature of Processor Junction) satisfy a demand condition of 0∼100$\^{C}$ under 11.5W of CPU heat.

• 플랜트 저널
• /
• 제4권3호
• /
• pp.54-59
• /
• 2008

The resonance of boiler is caused by exciting force in the gas path and it generates the vibration by the harmony of boiler's dimensional factor. According to trending toward the boiler of increasing capacity and a bigger size, it has a problem of the vibration at back-pass heating surfaces. We can predict such vibrations as comparison between vortex frequency and gas column's natural frequency. We can't rely on the method for the past decades because of changing parameters, such as an allowable error, gas temperature, gas velocity, Strouhal number. We can reduce the vibration to use the seasoning effect and change the operating condition in coal fired boiler but it's not essential solution. When the vibration occurred in the model boiler, we must measures the acoustic pressure and frequency of places for considering the means. So far, we confirmed the problem from field measures and theoretical analysis about the acoustic vibration of boiler. We installed anti-acoustic baffle in a existing boiler to change the acoustic natural frequency at the cavity, which results in reducing the acoustic vibration. The first, we prove that the acoustic resonance is caused by harmonizing vortex shedding frequency of tube heat surface with acoustic natural frequency of cavity in the range of 650~750 MW loads. The second, the acoustic resonance at the back-pass heating surface has the third order of acoustic natural frequency at the second economizer. We install five anti-acoustic baffles at the second economizer to reducing the resonance. We confirm considerably reducing the acoustic vibration of boiler during the commercial boiler.

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권10호
• /
• pp.1244-1250
• /
• 2014

The temperature of the main engine cabin of commercial vessel is very high. The material SS-316L undergoes creep damage at temperatures exceeding $450^{\circ}C$. It is essential to maintain the highly stressed engine cabin below the creep regime. Hence, seawater is employed in this kind of maritime vehicles as cooling liquid. It obtains the thermal energy at the cooling pipe line after passing through main engine cooling system. To harness the energy in the seawater, a turbine can be installed to absorb the energy in the seawater before being released into the sea. In this study, a cooling pipe line is selected to apply the tubular type hydro turbine for transferring the energy. Numerical analysis for investigating the performance and the internal flow characteristics of the tubular turbine is conducted. The results show that the maximum efficiency of 85.8% is achieved although the efficiency drops rapidly at partial flow rate condition. The efficiency descends slowly at the condition of excess flow rate. There is a relatively wide operating range of flow rate of this turbine to keep high efficiency at the excess flow rate condition. For the internal flow of the turbine, there is uniform streamline on the suction and pressure sides of the blade at the design point. However, the secondary flow appears at the suction and pressure sidesat the excess flow rate.In addition, it appears only at pressure side at the partial flow rate condition.

• Journal of Korean Society for Atmospheric Environment
• /
• 제19권E3호
• /
• pp.121-127
• /
• 2003

The characteristics of heterogeneous photocatalytic decomposition were investigated at low concentration level of $O_3$on TiO$_2$for various operating parameters such as: loaded catalyst weight (0∼4 mg/$\textrm{cm}^2$), initial concentration of $O_3$(0.06∼10.0 ppm), gas flow rate (1.0 ∼ 2.5ι/min), and relative humidity (0∼80%). This study was conducted using a flow-type reactor at room temperature. Three kinds of pure TiO$_2$(P25, ST -01, and E- 23) were employed as photocatalyts. It was found that $O_3$removal ratio was identical, regardless of the loaded TiO$_2$weight in the range from 0.5 to 4.0 mg/$\textrm{cm}^2$. It was also found that higher initial ozone concentration results in greater oxidation rate of ozone and experimental data show kinetically a good agreement with Langmur-Hinshelwood kinetic model. We also observed that the removal ratio of $O_3$increases linearly with the increasing flow rate and also with the increasing relative humidity for each catalyst.

• 대한조선학회논문집
• /
• 제34권4호
• /
• pp.42-52
• /
• 1997

수중램제트(underwater ram-jet)는 램흡입부(ram intake), 혼합실(mixing chamber) 및 노즐(nozzle)로 구성되어 있으며, 램흡입부로 유입된 작동유체는 압력이 증가되며 이 증압된 작동유체에 혼합실로부터 고압공기를 분사하여 기 액이상류를 형성하여 노즐을 통과하면서 대기압까지 팽창을 하여 작동유체를 고속으로 가속시켜 노즐출구로부터 추력을 얻는 방식으로 차세대 초고속 선박추진장치이다. 본 연구에서는 80노트를 낼 수 있는 선내관통형(buried type vessel) 램제트의 최적 노즐형상데이터를 이용하여 제반변수(벽마찰계수, 가스속도, 기포반경, 대기온도, 질량유량비, 디퓨저면적비, 작동유체의 속도구배)의 변화가 추진특성에 미치는 영향을 파악하였다.

• Korean Chemical Engineering Research
• /
• 제40권6호
• /
• pp.725-728
• /
• 2002

NOx와 먼지 동시 제거용 기능성 여과포 개발의 일환으로 $V_2O_5/TiO_2$ 계열의 상용촉매를 사용하여 P-84, Nomex, PTFE 여과포에 코팅하였다. 사용된 코팅 방법은 Sol-gel법, Spray 법 그리고 Dip 코팅 방법이었으며 코팅방법이 여과포의 NOx 제거 반응에 미치는 영향을 조사하였다. NOx 제거반응실험은 여과포의 작동온도에 맞는 $100-250^{\circ}C$의 반응온도범위에서, 공간속도 $5,000hr^{-1}$, 산소농도 6%, $NH_3/NO$ 몰비는 1.0의 조건하에서 수행되었다. 본 연구에서 시도된 세 가지 코팅 방법 중 촉매량의 조절 및 균일한 코팅이 용이한 Sol-gel법에 의해 제조된 기능성여과포가 가장 좋은 NOx 전환율을 나타냈다.

• Nuclear Engineering and Technology
• /
• 제27권3호
• /
• pp.336-343
• /
• 1995

적응제어의 한 방식인 자기동조제어(STR) 방식이 비선형 노심 모델의 출력 조정에 적용된다. 적응제어는 비선형, 시변 및 확률(Stochastic) 시스템을 위한 준최적 제어기를 설계하기 위한 적절한 제어 방식이다. 제어계통은 미지의 시변 파라메타를 갖는 3차 선형 모델에 기초한다. 파라메타는 가변 망각계수를 도입한 늑장 최소자승법에 의하여 매시간(Time Step) 순환적으로 평가된다. 평가된 파라메타를 이용하여 한 스텝 먼저 냉자재 평균온도가 예측되고 이 예측된 값과 Setpoint 값과의 차이를 최소화함은 물론, 제어봉의 움직임을 막고자 가중(Weighted) One-step-ahead 제어기가 설계된다. 또한 적분동작이 첨가되어 정상상태 에러가 제거된다. 넓은 운전영역을 포괄하는 비선형 PWR 모델이 원자로 출력 조정을 위한 본 제어기를 시뮬레이션하는데 이용되었다. 시뮬레이션 결과로부터 본 제어기의 성능이 우수한 것으로 판명되었다.

• 한국주조공학회지
• /
• 제31권5호
• /
• pp.293-301
• /
• 2011

Representative magnesium alloys applied to the die-casting are AZ91, AM60, etc., and the application of these alloys is restricted to components operating at moderate temperatures, due to grain boundary siding of ${\beta}$-phase($Mg_{17}Al_{12}$) at temperatures above $120^{\circ}C$. Heat-resistant magnesium alloys such as AE42, AE44 have been developed, but that have been too burdensome to produce because of the expensive rare earth materials. Research work for the development of low-priced heat-resistant magnesium alloy is actively in progress and positive results are being reported. This study aims to investigate the effect of Ca additions on mechanical properties of Mg-4Al-2Sn heat resistant magnesium alloys. Mg-4Al-2Sn alloys with Ca (0wt.%, 0.3wt.%, 0.7wt.%, 1wt.%) have been produced through the die-casting process for the development of low-priced heat-resistant magnesium alloy, and high temperature tensile tests are performed using the specimens. The results showed that mechanical properties of Mg-4Al-2Sn-xCa increased with the addition of Ca up to 0.7wt.% Ca and further addition of Ca deteriorated the mechanical properties of the alloys. A significant amount of porosity was observed at the sample with 1wt%. Ca and the longer freezing range of the alloy was believed to cause the formation of porosity.