• 대한기계학회논문집
• /
• 제19권3호
• /
• pp.796-805
• /
• 1995

For the purpose of improving performances of a turbocharged diesel engine at low speed, this study investigates the effects of the injected air for the performances and flow characteristics in the intake and exhaust pipes by using the computer simulation with test bed. In the theoretical analysis, the whole flow system, including engine cylinders and intake and exhaust pipes, is calculated numerically by the method of filling and emptying. From the results of this study, the following conclusions may be summarized. Increasing injected air pressure into the pipe of compressor exit brings about the improvement in a performance and flow characteristics of intake and exhaust pipes under full load operating conditions at 1000 rpm of the engine speed, but shows trends of the inferior performances under no load operating conditions at 2000 rpm of the engine speed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.476-479
• /
• 1997

A Knowledge of friction force in pneumatic cylinders makes it possible to improve cylinder description during simulation and to asses performance under changing operating conditions more accurately. Such knowledge is particularly useful, for example, when modeling continuous pneumatic positioning systems or predicting the operating conditions under which stick slip may occur, as well as in establishing preventive maintenance procedures for pneumatic cylinders. Friction force depends on a number of factors, including operating pressure, seal running speed on the cylinder barrel and rod, barrel material and surface roughness, seal dimensions and profile, seal material, lubrication conditions, cylinder distortion during assembly, and the operating temperature of cylinder components. This paper shows a system for measuring the friction force caused by a seal used in pneumatic cylinders. Results of experimental tests show that seal friction forces for grease lubricated service are clearly dependent on speed and pressure and are les sensitivity to other parameter. i.e., barrel material and roughness, seal material, and profile.

• 조명전기설비학회논문지
• /
• 제25권7호
• /
• pp.15-25
• /
• 2011

This proposes an online loss minimization algorithm for series PI(SPI) based interior permanent magnet synchronous motor(IPMSM) drive to yield high efficiency and high dynamic performance over wide speed range. The loss minimization algorithm is developed based on the motor model. In order to minimize the controllable electrical losses of the motor and thereby maximize the operating efficiency, the d-axis armature current is controlled optimally according to the operating speed and load conditions. For vector control purpose, a SPI is used as a speed controller which enables the utilization of the reluctance torque to achieve high dynamic performance as well as to operate the motor over a wide speed range. Also, this paper proposes current control of model reference adaptive fuzzy controller(MFC), and estimation of speed using artificial neural network(ANN) controller. The proposed efficiency optimization control, SPI, MFC, ANN in this paper is applied to IPMSM drive system, the validity of this paper is proved by analyzing response characteristics in variety operating conditions.

• 한국소음진동공학회논문집
• /
• 제26권7호
• /
• pp.857-864
• /
• 2016

In the present work, vibration analysis of high speed rotary bell cup model for paint atomizer application is carried out through numerical simulation. At first, eight bell cup models, considering four different cup shapes and two different cup diameters, are proposed and corresponding dynamic characteristics are investigated. To evaluate the operating stability, critical speed analysis is conducted using Campbell diagram and separation margin between operating speed and critical speed is identified. Unbalance vibration responses are also studied according to operating speed and balancing quality grade of G. Finally, the stability and adequacy of the proposed bell cup models are discussed for field application.

• 전기전자학회논문지
• /
• 제10권2호통권19호
• /
• pp.128-133
• /
• 2006

본 논문에서는 고속 통신용 인터페이스 회로를 RMVL(redundant multi-valued logic)을 이용하여 CMOS 회로로 설계하였다 설계한 1:4 디멀티플렉서 (demuitiplexer, serial-parallel convertor)는 직렬 데이터를 병렬 redundant 다치 데이터로 변환하는 부호화 회로와 redundant 다치 데이터를 병렬 이진 데이터로 변환하는 복호화 회로로 구성된다. 이 회로는 0.35um 표준 CMOS 공정을 이용하여 구현하였으며, 기존의 이진 논리회로보다 고속 동작을 한다. 이 회로는 3.3V의 공급전원에서 4.5Gb/s 이상의 동작속도와 53mW의 전력소모를 가지며, 동작속도는 0.35um 공정이 가지는 최대 주파수에 의해 제한된다. 설계한 회로가 높은 동작 주파수를 가지는 미세공정상에서 사용될 경우 100b/s 이상의 고속 통신용 인터페이스 구현이 가능하다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2005년도 춘계학술대회 논문집
• /
• pp.362-368
• /
• 2005

The KTX is now operating to the commercial purpose at Gyeong-Bu high speed railroad and Ho-Nam conventional railroad to be started on April, 2004. The trains were not found any problems at high speed railroad, but at Ho-Nam line were known to be have the few problems due to operating no planed. In this report should be studied for the effects of the lateral forces and wheel bases, brake distances etc., that high speed trains should be considered on curve running at the conventional railroad. The studied contents for operating at the conventional railroad shall be checked for the technical requirements from design stage, and the trains should be supplied and manufactured to car system to have the good running performances.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.2306-2309
• /
• 2011

With the opening of 1st phase and 2nd phase in Gyeongbu High Speed Line, KTX(The Korea Train Express) and Sancheon(2nd generation of High Speed Train) are operating commercially on entire line. Gyeongbu High Speed Line can be separated as several sections. In this entire line, a few types of train has operating by it's own pattern. However, commercial speed of the line compared with the maximum speed of Train is rather slow. Through this study, I found the reason of the slow speed on the Catenary system and suggested a solution.

• Tribology and Lubricants
• /
• 제12권4호
• /
• pp.28-34
• /
• 1996

The lubrication characteristics of high-speed ball bearings have been investigated empirically using 45mm bore split inner ring ball bearings employed in small industrial gas turbine engines with oil-jet lubrication method. For the close structural simulation, experiments carried out with bearing mounting supports of real engines, such as bearing housings and oil nozzle assemblies with squeeze film dampers. Thus the results of tests can be directly applied to the design and the development of gas turbine engines. Testing was done by varying operating speeds, axial load on bearings, and lubricant flow rates. During testing, the temperature of bearing at outer-ring face, the power consumption of the driving motor, and the rotating resistance of the bearing were measured. From this study, the representative factors for lubrication characteristics at high speed was found, and the most important one was not operating speed but axial load up to 1.95 million dmN speed and 2969 N axial load. Furthermore, the detailed variation of the rotational resistance of the bearing could be visualized by measuring the change of the radial load under the bearing supports. The rotational resistance consists of the frictional resistance and the bearing-cavity oil resistance.

• 대한안전경영과학회지
• /
• 제10권4호
• /
• pp.47-56
• /
• 2008

This study suggest a way to improve duty process of KTX(Korea Train Express) high-speed train driver. A new operating system which based on safety was introduced to operate high-speed train which travel above 300km/h on the high-speed railroad but below 200km/h on the general railroad. There were some studies on the operation of high-speed train which travel on the high-speed railroad and on the general railroad with safety. However they overlooked the elements of human errors. The duty-load of KTX train driver's 14 basic operation processes was measured using NASA-TLX and found four processes with high duty-load. In this paper, critical tasks of the high duty-load processes are determined using a questionnaire. Some suggestions which include the improvement of facilities, operating system and operating skill are proposed to lighten duty-load of the critical tasks. The validity of the proposed new task processes is demonstrated by making question to KTX train driver. To use this results cost-benefit analysis, hazards analysis etc. should be performed additionally.

• 전기학회논문지
• /
• 제65권5호
• /
• pp.724-729
• /
• 2016

Nowadays high-cost energy storage system using flywheel or secondary battery is applying to hybrid generation system with WT(Wind Turbine) and diesel generator in island areas for stable operation. This paper proposes an operating algorithm and modeling method of the hybrid generation system that can operate for variable wind speed and load, which is composed of energy storage system, variable-speed PMSG(Permanent Magnet Synchronous Generator) WT and diesel generator applied in island areas. Initially, the operating algorithm was proposed for frequency and voltage to be maintained within the proper ranges for load and wind speed changes. Also, the modeling method is proposed for variable speed PMSG WT, diesel generator and BESS(Battery Energy Storage System). The proposed operating algorithm and modeling method were applied to a typical island area. The frequency and voltage was kept within the permissible ranges and the proposed method was proven to be appropriate through simulations.