• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.10a
• /
• pp.745-748
• /
• 2003

This paper presents a study on pull cord switch system which is employed in various industry for emergency stop of the equipments. By using power line communication(PLC) technique, in this paper, a new method for operation position detection of pull cord switch is suggested without complicated wiring of separate cables which utilize only 2 lines. Also, using control function of PLC IC, a reset signal for each switch reset can be implemented in the switch status control/sensing device. Finally, this paper shows validity and practical applicability of the proposed operating position sensing system of pull cord switch by implementing the system and revealing the response time and signal through the PLC line.

• Nuclear Engineering and Technology
• /
• v.43 no.3
• /
• pp.301-308
• /
• 2011

The diametral creep of pressure tubes (PTs) in CANDU (CANada Deuterium Uranium) reactors is one of the principal aging mechanisms governing the heat transfer and hydraulic degradation of the heat transport system (HTS). PT diametral creep leads to diametral expansion, which affects the thermal hydraulic characteristics of the coolant channels and the critical heat flux (CHF). The CHF is a major parameter determining the critical channel power (CCP), which is used in the trip setpoint calculations of regional overpower protection (ROP) systems. Therefore, it is essential to predict PT diametral creep in CANDU reactors. PT diametral creep is caused mainly by fast neutron irradiation, temperature and applied stress. The objective of this study was to develop a bundle position-wise linear model (BPLM) to predict PT diametral creep employing previously measured PT diameters and HTS operating conditions. The linear model was optimized using a genetic algorithm and was devised based on a bundle position because it is expected that each bundle position in a PT channel has inherent characteristics. The proposed BPLM for predicting PT diametral creep was confirmed using the operating data of the Wolsung nuclear power plant in Korea. The linear model was able to predict PT diametral creep accurately.

• Journal of Power Electronics
• /
• v.9 no.1
• /
• pp.74-84
• /
• 2009

The design and implementation of a high performance PID (Proportional Integral & Differential) style controller with zero-phase error tracking property is considered in this article. Unlike a ball screw driven system, the controller in a direct drive system should provide a high level of tracking performance while avoiding the problems due to the absence of the gear system. The stiff mechanical element in a direct drive system allows high precise positioning capability, but relatively high tracking ability with minimal position error is required. In this work, a feasible position controller named 'Unified PID controller' is presented. It will be shown that the function of the closed position loop can be designed into unity gain system in continuous time domain to provide minimal position error. The focus of this work is in two areas. First, easy gain tunable PID position controller without speed control loop is designed in order to construct feasible high performance drive system. Second, a simple but powerful zero phase error tracking strategy using the pre-designed function of the main control loop is presented for minimal tracking error in all operating conditions. Experimental results with a s-curve based position pattern commonly used in industrial field demonstrate the feasibility and effective performance of the approach.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.525-528
• /
• 2000

This paper presents a circuit analysis and cotnrol example of favored configuration 6/4 SRM. SRM modeling and analysis are necessary for experiment. Thus this paper proposes a SRM modeling with PI controller (of driving converter) input voltage chopping and inductance profile when rotor position transformed. Through this simulation the designer can predict operating states of systems over a broad range of operating conditions.

• Journal of Biosystems Engineering
• /
• v.15 no.4
• /
• pp.281-289
• /
• 1990

A frequency-domain, system-identification method using a binary multifrequency signal was developed to find the transfer function between smoke intensity and throttle position in a diesel engine. This paper describes the simulation study performed to test the identification method developed. With an assumption of a diesel operation in a limited region about the normal operating state, the linear theory was adopted. Because that air fuel ratio is one of the most important operating variables causing smoke production in diesel combustion, single-input and single-output model was adopted.

• Management Science and Financial Engineering
• /
• v.2 no.1
• /
• pp.1-18
• /
• 1996

FMS operating system consists of several subsystems in general. i.e. tool grouping subsystem. tool/job assignment subsystem. job dispatching subsystem, and papers dealing with each subsystem were published by many researchers [1], [4], [6], [8], [9], [10], [11], [12], [13], [14], [15], [16]. This paper mainly discusses about tool/job assignment subsystem as a job loading procedure. that occupies the kernel position of overall FMS operating system. Its performance is evaluated through simulation experiments of an integrated operating system under a typical FMS hardware configuration implemented in many machining factories, which is composed of the proposed procedure as well as a job dispatching procedure including several heuristic dispatching rules in terms of rule-base.

• Tribology and Lubricants
• /
• v.10 no.4
• /
• pp.33-42
• /
• 1994

An influence of inlet pressure on the performance of sector-shaped pad thrust bearings is investigated theoretically. The optimum conditions of film thickness or the optimum positions of pivot are found through the evaluation of load capacity for all available conditions of film thickness, under the operating conditions which the thermal and pad deformation effects can be neglected. The bearing performance including the inlet pressure effects is obtained for a wide operating ranges that inertia parameter(Re$^{*}$) is up to unity, and for the various cases of pad extent angle (number of pad) and the three cases of the angle between pads. The results show that the inlet pressure has a large influence on the performance of sector-shaped pad thrust bearings. In the design of sector-shaped pad bearings, due to the inlet pressure, the optimum number of pad is varied with the operating speed and the angle between pads, and the optimum position of pivot is located toward the leading edge along with the operating speed increases.

• Transactions on Control, Automation and Systems Engineering
• /
• v.4 no.1
• /
• pp.38-42
• /
• 2002

Conditions are discussed for operating a dissymmetric human master-small (or micro) slave system in best (large position gain-small velocity gain) conditions allowing higher operator dexterity when real effects (joint compliance, link flexion delay and transmission distortion) are taken into account. It is shown that position PD feedback law advantage for ideal case no longer holds, and that more complicated feedback law depending on real effects has to be implemented with adapted transmission line. Drawback is slowdown of master slave interaction, suggesting to use more advanced predictive methods for the master and more intelligent control law for the slave.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.288-288
• /
• 2009

Most of Static electricity forms part of our daily experience broadly. Most people have noticed from time to time electric shocks when closing of their car or after walking across a carpet, operating shredder in winter and touching a metal handle. This electrostatic discharge nuisance is normally a minor inconvenience, but in some cases static electricity can cause more serious problems. Static electricity can also be harnessed to good effect in Position Control System.

• Journal of the Semiconductor & Display Technology
• /
• v.8 no.4
• /
• pp.21-24
• /
• 2009

We investigated a nanoscale inertia sensor based on telescoping carbon nanotubes, using classical molecular dynamics simulations. The position of the telescoping nanotubes is controlled by the centrifugal force exerted by the rotation platform, thus, position shifts are determined by the capacitance between carbon nanotubes and the electrode, and the operating frequency of the carbon nanotube oscillator. This measurement system, tracking oscillations of the carbon nanotube oscillator, can be used as the sensor for numerous types of devices, such as motion detectors, accelerometers and acoustic sensors.