• Journal of Power Electronics
• /
• 제12권2호
• /
• pp.317-325
• /
• 2012

Resonant immittance converter (RIC) topologies can transform a current source into a voltage source (Type-I RICs) and vice versa (Type-II RICs), thereby making them suitable for many power electronics applications. RICs are operated at a fixed frequency where the resonant immittance network (RIN) exhibits immittance conversion characteristics. It is observed that the low-frequency response of Type-II RINs is relatively flat and that the state variables associated with Type-II RINs affect the response only at the high frequencies in the vicinity of the switching frequency. The overall response of a Type-II RIC is thus dominated by the filter response, which is particularly important for the controller design. Therefore, an approximate equivalent circuit model and a small-signal model of Type-II RICs are proposed in this paper, neglecting the high-frequency response of Type-II RINs. While the proposed models greatly simplify and speed-up the analysis, it adequately predicts the open-loop transient and small-signal ac behavior of Type-II RICs. The validity of the proposed models is confirmed by comparisons of their results with those obtained from a cycle-by-cycle simulation and with an experimental prototype.

• 천문학회보
• /
• 제36권2호
• /
• pp.90.2-90.2
• /
• 2011

At Kyoto University, a continuous solar full-disk observation in CaII K line had been done during 44 years of 1926 - 1969. The observation was done with a Askania spectroheliograph on daily base. The images were taken on photographic plates. We started a project to archive these image data into a digital database which will be open to the public for scientific researches. One of the scientific usage of the database is to study the long term variation of the solar chromospheres. Since the area of CaII K plage area is a measure of solar chromospheric heating, we can do comparative study of the sunspot cycle and the chromospheric heating cycle of the sun. Another interesting field of scientific utilization of the database is the long term variation of the heating of terrestrial upper atmosphere. As was shown by Yokoyama, Masuda and Sato (2005), the area of the CaII K plage is a good proxy measure of solar EUV irradiation onto the upper atmosphere of the earth. Thus the completion of our database will serve to supply a basic and long-span data for upper atmospheric heating issues by the cooperative study with the Inter-university Upper atmosphere Global Observation NETwork (IUGONET) developed in Japan.

• Child Studies in Asia-Pacific Contexts
• /
• 제3권1호
• /
• pp.13-31
• /
• 2013

The children of sex workers in Bangladesh are denied even the most basic human rights. This article is based on recent research focused on the children of sex workers in the context of their everyday lives. The study focused on access to education and how education could be a vehicle for them to break the vicious cycle of exploitation. This was a mixed method interpretative study which employed qualitative and quantitative approaches, but in this paper only qualitative data which was generated through in-depth interviews and focus group discussions is used. Data was collected from sex workers, their children, teachers and NGO workers who participated in the study. Information has been collected for analysing the expectation of the children of sex workers and hope for the future, and the opportunities available to them during their schooling. Thematic analysis technique was used to understand the challenges and barriers faced by the children of sex workers in fulfilling their educational aspirations. The lives of the children of sex workers are marginalised by the mainstream society. Though it is very difficult to break the vicious cycle of exploitation, this research finds that education may be a stepping stone for them to create a better future. However, it is argued that the children of sex workers need income generating vocational and technical education to enable them to earn and support their family. Policy recommendations have been made in order to achieve Education For All targets and Millennium Development Goals, and to provide a second chance for these vulnerable young people to have a better life.

• 대한인간공학회지
• /
• 제28권3호
• /
• pp.49-54
• /
• 2009

Visual occlusion method is a visual demand measuring technique which uses periodic vision/occlusion cycle to simulate driving environment. It became one of the most popular techniques for the evaluation of in-vehicle interfaces due to its robustness and cost-effectiveness. However, it has a limitation in that the vision/occlusion cycle forces the user to use the IVIS at a predetermined pace, while a driver decides when to use the device on his/her own in actual driving. This paper proposes a user-driven visual occlusion method for measuring the visual demand of in-vehicle interfaces. An experiment was conducted to examine the visual demand of an in-vehicle interface prototype using both the existing (system-driven) occlusion method and the proposed (user-driven) one. Two in-vehicle tasks were evaluated: address input and radio tuning. The results showed that, for the radio tuning task, there were significant differences in total shutter open time and resumability ratio between the methods. The user-driven visual occlusion method not only allows a better representation of drivers' behavior, but it also seems to provide more information on the chunkability of a task.

• Advances in aircraft and spacecraft science
• /
• 제1권4호
• /
• pp.409-425
• /
• 2014

Converging flows of a gas and a liquid at a microchannel cross junction, under proper conditions, can result in the formation of periodic, dispersed microslugs. This microslug formation phenomenon has been proposed as the basis for a fuel injection system in a novel, 'discrete' monopropellant microthruster designed for use in next-generation miniaturized satellites. Previous experimental studies demonstrated the ability to generate fuel slugs with characteristics commensurate with the intended application during steady-state operation. In this work, numerical and experimental techniques are used to study the effect of valve actuation on slug characteristics, and the results are used to compare with equivalent steady-state slugs. Computational simulations of a valve with a 1 ms valve-actuation cycle show that as the ratio of the response time of the valve to the fully open time is increased, transient effects can increase slug length by up to 17%. The simulations also demonstrate that the effect of the valve is largely independent of surface tension coefficient, which is the thermophysical parameter most responsible for slug formation characteristics. Flow visualization experiments performed using a miniature valve with a 20 ms response time showed less than a 1% change in the length of slugs formed during the actuation cycle. The results of this study indicate that impulse bit and thrust calculations can discount transient effects for slower valves, but as valve technology improves transient effects may become more significant.

• Corrosion Science and Technology
• /
• 제10권5호
• /
• pp.167-174
• /
• 2011

Due to commercialization of nuclear power, most countries have taken interest in decontamination process of nuclear power plant and tried to develop a optimum process. Because open literature of the decontamination process are rare, it is hard to obtain skills on decontamination of foreign country and it is necessarily to develop proper chemical decontamination process system in Korea. In this study, applicable possibility in chemical decontamination for reactor coolant pump (RCP) was investigated for the various stainless steels. The stainless steel (STS) 304 showed the best electrochemical properties for corrosion resistance and the lowest weight loss ratio in chemical decontamination process with immersion type than other materials. However, the pitting corrosion was generated in both STS 415 and STS 431 with the increasing numbers of cycle. The intergranular corrosion in STS 431 was sporadically observed. The sizes of their pitting corrosion also increased with increasing cycle numbers.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제34회 춘계학술대회논문집
• /
• pp.21-24
• /
• 2010

다단연소사이클 액체로켓엔진에 사용 가능한 예연소기의 냉각채널에 대한 해석연구를 진행하였다. 해석에 사용된 예연소기는 내부압력이 210 bar로서 한국형발사체에 사용되는 엔진이나 30톤급 엔진에 비해 매우 높으며 개방형 엔진의 가스발생기와는 달리 연소실 내부에서 산화제 과잉 연소를 하기 때문에 냉각방법이 까다롭고 또 그만큼 냉각채널의 역할이 매우 중요해진다. 이를 위해 매우 다양한 형상의 냉각채널이 고안되었고 이들의 유동해석을 실시하였다. 결과적으로 냉각채널의 차압을 목표 차압 아래로 달성할 수 있었다.

• 한국전기전자재료학회논문지
• /
• 제21권5호
• /
• pp.434-439
• /
• 2008

Silver pastes as the outer electrodes have been prepared using Pb-free glass frits with different content of $Bi_2O_3$ and the effects of glass composition on the degradation behaviors of the Ag electrodes were investigated using the change of adhesion between Ag electrode and alumina substrate with thermal cycle stress. Low adhesion and high surface resistance were observed in Ag electrode using glass frit with a $Bi_2O_3$ content of 60 wt%, owing to the open microstructure formed at the firing temperature of $600^{\circ}C$. When the $Bi_2O_3$ was increased to 80 wt% in the glass frit, the Ag electrodes had a dense microstructure with high adhesion and a low surface resistance. Delamination of the Ag electrodes was a major failure mode under thermal cycle stress and this was attributed to residual stress due to the thermal expansion mismatch between the Ag electrode and the alumina substrate.

• Design & Manufacturing
• /
• 제14권4호
• /
• pp.25-39
• /
• 2020

In this study, an edge device that monitors the injection molding process by measuring the mold vibration(acceleration) signal and the mold surface temperature was developed and evaluated its performance. During injection molding, signals of the injection start, V/P switchover, and packing end sections were obtained through the measurement of the mold vibration and the injection time and packing time were calculated by using the difference between the times of the sections. Then, the mold closed and mold open signals were obtained using a magnetic hall sensor, and cycle time was calculated by using the time difference between the mold closed time each process. As a result of evaluating the performance by comparing the process data monitored by the edge device with the shot data recorded on the injection molding machine, the cycle time, injection time, and packing time showed very small error of 0.70±0.38%, 1.40±1.17%, and 0.69±0.82%, respectively, and the values close to the actual were monitored and the accuracy and reliability of the edge device were confirmed. In addition, it was confirmed that the mold surface temperature measured by the edge device was similar to the actual mold surface temperature.

• 한국지하수토양환경학회지:지하수토양환경
• /
• 제27권2호
• /
• pp.36-40
• /
• 2022

To respond to rapidly changing water circumstances such as climate change, drought, etc., the korean government (MOE) established four advanced strategies for integrated groundwater management. The first strategy is watershed-based management of groundwater. The second strategy is total quantity management of groundwater including improvement of groundwater preservation area policy and procedure of investigation for groundwater influence area, additional construction of groundwater dam, installation of large-scale public wells, extention of spilled groundwater use. The third strategy is prevention of groundwater contamination including expansion of monitoring wells, introducing declaration of groundwater contamination. The last strategy is advancement of groundwater information management including integrated management of data, setting up a big-data based open platform. The above-mentioned four strategies will be reflected in the 4th National Groundwater Management Plan to secure implementation power, and it is expected to laid the foundation for advanced and rational groundwater management system.