• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1995년도 춘계학술대회 논문집
• /
• pp.145-149
• /
• 1995

The metallization is the key to determining cell costs, call performance, and cell and system reliabiltiy. The Burled Contact Solar Cell (BCSC) was specifical1y desinged to be compatible tilth low cost, mass production techniques and avoid the conventional metallization problem. By using electroless plating trchniqeu, we performed this metallization inexpensively and reliabley, This paper presents the details of the optimization procedure of metallization schemes on laser grooved cell surface Commercially available Ni ,Cu, and Ag plating solutions were applied for the cell metallization. The application of those solutions on the buried contact front metalization has resulted in an cell efficiency of 18.5% The cell parameters are an open circuit voltage of 651 mV, short circuit current density of 38.6 mA/$\textrm{cm}^2$, and fill factor of 73.5%.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 춘계학술대회 논문집
• /
• pp.438-440
• /
• 2008

Effects of Ga contents of CIGS absorber layer on the performance of thin films solar cells were investigated. As Ga content increased, the grain size of CIGS films decreased presumably because Ga diffusion during 2nd stage of co-evaporation process is more difficult than In diffusion. Performances of corresponding solar cell show systematic dependence on Ga content in which open circuit voltage increases and short circuit current and fill factor decrease as Ga contents increases. At a optimal condition of Ga/(In+Ga)=0.27, the solar cell shows a conversion efficiency of 15.6% with $V_{OC}$ of 0.625 V, $J_{SC}$ of 35.03 mA/$cm^2$ and FF of 71.3%.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.1382-1383
• /
• 2011

결정질 실리콘 태양전지에서 전극 형성 공정은 Voc(Open-circuit voltage), Isc(Short-circuit current), Rser(Series resistance), Rshunt(Shunt resistance), FF(Fill factor) 특성에 영향을 주기 때문에 매우 중요하다. 하지만 paste와 선 공정에서의 조건에 따라 특성이 바뀌기 때문에 소성 공정을 최적화하기는 쉽지 않다. 본 연구에서는 Gravure Off-set printing 방식을 이용하여 결정질 실리콘 기판 표면에 미세 전극 형성 공정을 하고 소성 조건 최적화를 위해 peak 온도와 ramp-up 속도를 변화시켜 각 조건별 특성을 비교하였다. Peak 온도가 커질수록, contact resistance의 감소에 따라 Rser가 줄어들었다. 본 연구를 통해 Voc는 619mV, FF는 77.9%로 측정되는 Gravure Off-set 태양전지에 최적화된 소성 공정 조건을 확보하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.212-216
• /
• 2004

Bearingless motors are the rotational electric machine which utilize a common magnetic structure for rotation and magnetic suspension. Since the bearing function is combined with the motor, the shaft length can be shortened resulting in higher critical speeds. Relationship between suspension force and current of bearingless motor is clearly derived by prior research. However, relationship between displacement of rotor and suspension force is not precisely defined. In this paper, we present model of bearingless motor describing the radial force variation due to the movement of the rotor. Using a distributed magnetic circuit and maxwell stress tensor, we derived a mathematical expression for the radial force. For a slotless bearingless motor, we are able to find an analytical model presented in the form of stiffness. For a slotted motor, we can compute the stiffness by semi-analytical analysis. This model is validated by a finite-element-analysis.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.718-719
• /
• 2011

Lately, the demand for electrical power has been significantly increased. As a result a power transmission system has been improved. On the other hand fault current increased more than past. Superconducting fault current limiter (SFCL) is one of the solutions to limit fault current. However, SFCL's research has not advanced in a power transmission system fully. Therefore, we studied effect of SFCL in a power transmission system. The power distribution system is open-loop circuit, but a power transmission system is closed-loop system. Consequently, Fault current in a power transmission system is larger than fault current in a power distribution system. we exerimented a simple closed-loop power transmission system circuit.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.181_182
• /
• 2009

Some phenomena occurred when one phase of the line circuit breaker was opened while a generator was operating to connect with the power grid were simulated by PSCAD/EMTDC and the analysis for the reason of operation and non-operation of protective relay will contribute to prevent spreading damage when same prospective faults occur.

• 조명전기설비학회논문지
• /
• 제25권1호
• /
• pp.101-106
• /
• 2011

The failure of cooling system in Superconducting Fault Current Limiter(SFCL) increases the impedance of superconducting device, and due to malfunction of inner switches the SFCL opens the distribution system inadvertently when required to do so. In this paper, the ground fault and short circuit fault were classified as active failure and the open circuit fault was passive failure. A reliability model of SFCL considers the passive failure as well as active failure, and in the case study the reliability indices of distribution system are evaluated. It is possible that the reliability evaluation excluded passive failure makes the customers reliability seem so worse than it really was. Therefore, the reliability models of SFCL must include the active failure and passive failure together to evaluate the reliability of distribution system connected SFCL.

• Current Photovoltaic Research
• /
• 제4권2호
• /
• pp.48-53
• /
• 2016

We report the effect of physical load on the stability of organic solar cells under physical loads. The active layers in organic solar cells were fabricated with bulk heterojunction films (BHJ) films of poly (3-hexylthiophene) and phenyl-$C_{61}$-butyric methyl ester. The loading time was varied up to 60 s by keeping the physical load constant. Results showed that the open circuit voltage was not influenced by the physical load but other solar cell parameters were sensitive to the loading time. The fill factor was very slightly increased at 15 s, while short circuit current density was well kept for 30 s. The power conversion efficiency was reasonably maintained for 45 s but became significantly decreased by the continuous loading for 60 s.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2004년도 전력전자학술대회 논문집(2)
• /
• pp.713-717
• /
• 2004

This is a thesis that a quarter-brick size of 100W class open-frame type on board power module comprising telecommunication application is reported. The input voltage is established between 36 and 75 in range in order for power module to be utilized for the telecommunication application, and output were set at 3.3V and 30A. A number of parts used for transformer, inductor, and hit sink are composed of PCB in order for DC-DC converter to be lowered below 8 mm. A constant current control circuit was annexed to the system as well as basic protection prototypes such as over-voltage, over-current, and over-temperature were well considered to enhance more credibility, and were tested. As a result, high circuit performance and credibility turned out to be significant.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1993년도 추계학술대회 논문집
• /
• pp.60-63
• /
• 1993

We have prepared n-CdS/p-InP hetero- junction solar cells by thermal evaporation. The efficiency under the optium conditions without the grid line contact was 7.3%, and the solar cell having glid line contact with SiO AR coating was the open circuit voltage of 0.71V, the short circuit voltage current density of 15mA/cm$^2$, the fill factor of 0.73, and the efficiency of 11.5%. As result of photoresponse in 400-1000nm wavelength the cutoff of n-CdS/p-InP solar at 500nm results from absorption by the CdS \"window\" and the cutoff at 930 nm result from absorption by the InP.