• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2005.11a
• /
• pp.64-71
• /
• 2005

To achieve efficient supersonic combustion within a manageable length, a successful fuel injection scheme must provide rapid mixing between fuel and airstream. In former days, various injection concepts have been investigated. Cavity flow is the open type, that is, length-to-depth ratio L/D=4.8, aft ramp angle is $22.5^{\circ}$. An experimental study on a transverse cross jet injection into a Mach 1.92 supersonic main stream which flows over a cavity was carried out to investigate the effect of the momentum flux ratio(J), the jet interaction characteristics, and the pressure distribution in the combustor and using the primary diagnostics : schlieren visualization and wall static pressure measurements. Fuel penetration height and jet interaction characteristics depend strongly on the momentum flux ratio.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.127-134
• /
• 2011

A genetic algorithm (GA) has been employed to optimize the major design variables of the liquid rocket engine. Pressure of the main combustion chamber, nozzle expansion ratio and O/F ratio have been selected as design variables. The target engine has the open gas generator cycle using the LO2/RP-1 propellant. The gas properties of the combustion chamber have been obtained from CEA2 and the mass has been estimated using reference data. The objective function has been set as multi-objective function with the specific impulse and thrust to weight ratio using the weight method. The result shows about 4% improvement of the specific impulse and 23% increase of the thrust to weight ratio. The Pareto frontier line has been also obtained for various thrust requirements.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.51 no.11
• /
• pp.483-493
• /
• 2002

The damping ratio ${\xi}$ of the unit-step response of a second-order discrete system is a function of only the location of the closed-loop poles and is not directly related to the location of the system zero. However, the peak overshoot of the response is the function of both the damping ratio ${\xi}$ and an angle ${\alpha}$, which is the phasor angle of the damped sinusoidal response and is determined by the relative location of the zero with respect to the closed-loop poles. Therefore, if the zero and the open-loop poles are relatively adjusted, through pole-zero cancellation, to maintain the desired (or designed) closed-loop poles, the damping ratio ${\xi}$ will also be maintained, while the angle ${\alpha}$ changes. Accordingly, when the closed-loop system poles are fixed, the peak overshoot is considered as a function of the angle ${\alpha}$ or the system zero location. In this paper the effects of the relative location of the zero on the system performance of a second-order discrete system is studied, and a design method of digital compensator which achieves a minimum peak overshoot while maintaining the desired system mode and the damping ratio of the unit step response is presented.

• International Journal of Fluid Machinery and Systems
• /
• v.5 no.3
• /
• pp.117-125
• /
• 2012

In the present experimental study, the authors try to clarify the characteristics of the flow around and inside a cross-flow impeller in a typical geometry, over a wide parameter range of an aspect ratio $L/D_2$. In order to eliminate the complicated casing factors, the impeller rotates in open space without any casings. As a result, by using hot wire anemometer measurements and by conventional flow visualisations with a particle image velocimetry technique, the authors show that both the outflow rate and the maximum vorticity attain the maximum for $L/D_2$ = 0.6. In order to investigate the aspect-ratio effect, we further reveal minute fluctuating pressures on an impeller end wall for a singular $L/D_2$ = 0.6. Especially in these pressure measurements, the eccentric vortex is prevented to revolute by the insertion of a tongue, in order to consider the spatial structure of flow more precisely.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.4
• /
• pp.41-47
• /
• 2011

Turbopump, which is a part of 75 ton open cycle liquid rocket engine has a super sonic impulse turbine. This paper investigated the leading edge thickness effect on the turbine performance experimently. Two rotors were tested with the different leading edge thickness. The ratios (rotor thickness to Pitch) are 1.9 and 1.4 times to 30 ton turbine rotor. As a result, a rotor with 1.4 times ratio had a 1.5% higher efficiency gain than a rotor with 1.9 times ratio. The pressure ratio with the maximum efficiency on the same rotational speed was increased to the full expansion ratio of nozzle.

• Journal of the Korean Society of Combustion
• /
• v.14 no.4
• /
• pp.7-16
• /
• 2009

Porous metal plates (Metal fiber, muti-hole metal plate) using mainly in surface burner are known to have a corrosion and durability problem under high temperature condition. In this study, premixed flat flame with perforated ceramic tile of more durable cordierite material was examined with respect to combustion stability and emission. The flat premixed ceramic burner consists of perforated ceramic tile and various type of baffle plates to form stable surface flame. The results show that most stable flat flame is generated using baffle plate with open ratio of 0.193. In downward flat flame mode which is widely used in condensing boiler, CO is measured below 50ppm from equivalence ratio 0.755 to 0.765 and $NO_X$ is measured below 12ppm from equivalence ratio 0.75 to 0.79. It is also found that the range of blue flame in flame stability curve becomes wider with increasing heat capacity.

• Knee surgery & related research
• /
• v.30 no.4
• /
• pp.311-318
• /
• 2018

Purpose: The purpose of this study was to evaluate changes in the coronal alignment of the knee and ankle joints after open wedge high tibial osteotomy (OWHTO) to determine factors related to the recurrence (R) of the varus deformity by serial analysis. Materials and Methods: Sixty-four OWHTOs were enrolled in this study. The weight bearing line (WBL) ratio, joint line convergence angle (JLCA), knee joint inclination, mechanical axis-tibial plateau angle, talar inclination (TI), and distal tibia articular angle (DTAA) were serially assessed. Serial correlation analysis between all parameters was performed. Patients were divided into R group and no recurrence (NR) group according to the WBL ratio (55%) at postoperative one year. Results: The preoperative WBL ratio showed significantly negative correlation with serial changes of JLCA, TI, and DTAA (p<0.05). The JLCA, TI, and DTAA as well as WBL ratio showed a significantly larger degree of varus alignment in the R group than in NR group at postoperative 6 weeks and 1 year after OWHTO (p<0.05). Conclusions: Sufficient correction of the WBL and restoration of the JLCA during OWHTO are essential to prevention of the R of varus deformity after the surgery because they are the only modifiable factors during surgery. Level of Evidence: IV, Case series.

• Steel and Composite Structures
• /
• v.47 no.3
• /
• pp.437-450
• /
• 2023

A half open cross section built-up column, namely cold-formed thin-walled steel built-up column with 12-limbsection (CTSBC-12) is put forward. To deeply reveal the mechanical behaviors of CTSBC-12 under axial compression and put forward its calculation formula of axial bearing capacity, based on the previous axial compression experimental research, the finite element analysis (FEA) is conducted on 9 CTSBC-12 specimens, and then the variable parameter analysis is carried out. The results show the FEA is in good agreement with the experimental research, the ultimate bearing capacity error is within 10%. When the slenderness ratio is more than 96.54, the ultimate bearing capacity of CTSBC-12 decreases rapidly, and the failure mode changes from local buckling to global buckling. With the local buckling failure mode unchanged, the ultimate bearing capacity decreases gradually as the ratio of web height to thickness increases. Three methods are used for calculating the ultimate bearing capacity, the direct strength method of AISI S100-2007 gives result of ultimate axial load which is closest to the test and FEA results. But for simplicity and practicality, a simplified axial bearing capacity formula is proposed, which has better calculation accuracy with the slenderness ratio changing from 30 to 100.

• Journal of Korean Society of Forest Science
• /
• v.101 no.1
• /
• pp.46-52
• /
• 2012

The purpose of this study is to give ROI informations about management status and investment returns to someone who will newly cultivate lycium chinese miller or expand area of its cultivation. In this study, IRR, B/C Ratio and NPV is used for ROI analysis. We basically surveyed fifty two among Lycium Chinese Miller cultivation farmhouses in chief producing districts Chungnam Chungyang, Jeonnam Jindo in Korea from May until September in 2009. Hence, this study surveyed these farmers about production cost, management cost, input labors and materials, land price and etc. by working process to calculate production and operation cost. As the result of farm survey, average selling price of Lycium Chinese Miller is 15,000 won per kg at locals for five years. However, when 3% discount rate is applied, the result of the analysis is B/C Ratios 0.89, which shows unprofitable. Therefore, it is a possible baseline that price of Lycium Chinese Miller is at least 16,800 won per kg with 3.00% IRR and B/C Ratio is 1.00. It could be profitable with about 21.75% income ratio when price of Lycium Chinese Miller is 16,800 won per kg.

• Imaging Science in Dentistry
• /
• v.51 no.4
• /
• pp.421-427
• /
• 2021

Purpose: The pulp length to width (PL/W) ratio of the maxillary lateral incisor can be used as an age determination method. This study aimed to investigate the correlation between the PL/W ratio of the maxillary lateral incisor on panoramic radiographs and human chronological age in Indonesian subjects. Materials and Methods: This study analyzed with 134 maxillary lateral incisors on 113 panoramic radiographs from patients who visited the Oral and Maxillofacial Radiology Unit of Dental Hospital Universitas Padjadjaran, Bandung, Jawa Barat, Indonesia, from 2013 to 2018 (age range: between 11 to 60 years). The pulp length was measured from the pulp chamber roof to the apical foramen, and the pulp width was measured on the cervical area of the cementoenamel junction in millimeters using Fiji ImageJ open-source software. Simple linear regression (in SPSS) was used to analyze the results. The reliability of the observers was evaluated. Results: The PL/W ratio of the maxillary lateral incisor was significantly correlated with chronological age (P<0.01). No statistically significant difference was found in the PL/W ratio between the left and right maxillary lateral incisors(P=0.333). There was a very strong correlation (r=0.939) between the PL/W ratio of the maxillary lateral incisor and human chronological age, with the following formula: age= -3.057+1.875×PL/W ratio (R²=0.882, standard error of estimate: 4.659). Conclusion: The PL/W ratio of the maxillary lateral incisor on panoramic radiograph can be used for age determination in Indonesian subjects.