• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.4
• /
• pp.7-12
• /
• 2012

The cutting force for peripheral end-milling considering run-out property was estimated and its result was compared with that of measured one. An experimental coefficient modelling was used for the formulation of theoretical end-milling force by considering the specific cutting force coefficient. Also, the specific cutting force, that is the multiplication of specific cutting force coefficient and uncut chip thickness, was used for the prediction of end-milling force. The end-milling force mechanics with run-out was presented for the estimation of theoretical force in peripheral end-milling by considering the geometric shape of the workpiece part. As a result, the estimated end-milling force shows a good consistency with the measured one. And it can be used for the prediction of force history in end-milling with run-out which incurs different start and exit immersion angle in entering and exiting condition.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.321-324
• /
• 1998

A single phase induction motor (SPIM) rated in fractional horsepower is widely used in home and industrial equipment: washing machines, fans, refrigerators, etc. In this paper, authors present the experimental results of the SPIM under controlling of currents of main and auxiliary windings by using a one-chip micro stator(OMS). This new starting method is developed to replace the conventional starting device consisted with a mechanical switch and a capacitor. In mentioned method, the soft-starting of SPIM is simply implemented and higher efficiency is obtained in comparison with conventional condenser type SPIM.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.15 no.6
• /
• pp.494-505
• /
• 1990

This paper reports on the development of a DPSK demodulator of DS spread spectrum communications that use one SAW convolver. The spreading code chip pattern is changed from bit to bit in data portion of packet. And code chip is PSK modulated. Compared with simulation, experiment shows that the DPSK signal spreaded can be demodulated by using only one SAW convolver. And the theoretical performance of this DPSK demudulator is equal to CSK demodulator wich uses two SAW convolvers.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.30 no.2
• /
• pp.97-108
• /
• 1994

The DC Servo Motor has been used as an actuator in automatic control fields because of the good response and the control easiness nevertheless it has some disadvantage such as spark at the brush. Recently, along with the fast development of semiconductor industries, the digital control scheme is increasing in comparison with analog control because of the strength against noise and the accuracy. In this paper, authors proposed a combined control algorithm, which is mixed Modified Minimum Time Position Control(MMTPC) and PI control algorithm. for minimum time position control of DC Servo Motor by the one-chip microcontroller. The proposed control algorithm showed the fast response and offset-free. The validity of the proposed method comparing with the VSS control is proved by the response experiments.

• Proceedings of the Korean Society of Laser Processing Conference
• /
• 2006.11a
• /
• pp.53-81
• /
• 2006

A COG(Chip on Glass) bonding process that is one of display packaging technology and bonds between driver IC chip and a glass panel using ACF(Anisotropic Conductive Film)has been investigated by using diode laser. This method is possible to raise cure temperature of ACF within one second and can reduce the total process time for COG bonding by a conventional method such as a hot plate. Also we can get good pressure mark on the surface of electrodes and higher bonding strength than that by convention method. Results show that laser COG bonding can give low pressure bonding and decrease a warpage of panel. We believe that it can be applied to fine pitch module.

• Proceedings of the KIEE Conference
• /
• 2005.10a
• /
• pp.118-121
• /
• 2005

In this paper, it has been proposed the simultaneous controller of electronic ballast and PFC(power factor corrector) for fluorescent lamp by one chip micro-controller. Boost DC-DC converter is adopted for PFC, and half bridge inverter for electronic ballast. It controls, simultaneously and independently, the boost DC-DC converter and the half bridge inverter. As electronic ballast and PFC are controlled by one chip micro-controller, it is possible to achieve the cheaper controller for fluorescent lamp. Experimental result has shown the feasibility of the proposed simultaneous controller of PFC and electronic ballast.

• ETRI Journal
• /
• v.26 no.5
• /
• pp.509-511
• /
• 2004

This paper describes a novel current driving circuit for an active matrix organic light emitting diode (AMOLED). The proposed current driving circuit has a lower power consumption and higher chip density for the AMOLED display compared with the conventional one because all elements operate at a normal voltage and are shielded from the high voltage of the panel. The chip size and power consumption of the current driving circuit for an AMOLED can be improved by about 30 to 40% and 10 to 20%, respectively, compared with the conventional one.

• ETRI Journal
• /
• v.28 no.3
• /
• pp.397-400
• /
• 2006

The multi-layer advanced high-performance bus (ML-AHB) BusMatrix proposed by ARM is an excellent architecture for applying embedded systems with low power. However, there is one clock cycle delay for each master in the ML-AHB BusMatrix of the advanced microcontroller bus architecture (AMBA) design kit (ADK) whenever a master starts new transactions or changes the slave layers. In this letter, we propose an improved design method to remove the one clock cycle delay in the ML-AHB BusMatrix of an ADK. We also remarkably reduce the total area and power consumption of the ML-AHB BusMatrix of an ADK with the elimination of the heavy input stages.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.49 no.1
• /
• pp.70-76
• /
• 2000

This paper describes a one-chip micom controller and phase angle control method for self-starting and energy saving of single-phase induction motor. The proposed method is based on the optimal efficiency control which is running by variable phase angle of main winding current such as to maintain the maximum efficiency characteristics of the motor, in voltage control with TRIAC. Experiments are focused on a capacitor starting single-phase induction motor. The optimal energy saving by variable phase angle control are verified by experimental results. Also, auxiliary winding was controlled by electronic starting switch.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.40 no.12
• /
• pp.1262-1268
• /
• 1991

The electric furnace which has time delay and time varying characteristics cannot be controlled easily. In this paper, a fuzzy controller for a electric furnace is implemented using one chip processor 8751 and IBM PC. The fuzzy controller is implemented in the PC. The One chip processor 8751 can sense the furnace internal temperature and pass it to IBM PC and generate the driving signal for SSR. The membership function of the fuzzy controller is determined by Least Square method. from the experiments, we can show that the fuzzy controller can improve robustness to the load variation. And the settling time is reduce 4500 (sec) to 2500 (sec).