• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.3
• /
• pp.54-65
• /
• 1997

To quantify the LII signals from soot particle of flames in diesel engine cylinder, a new method has been proposed for correcting LII signal attenuated by soot particles between the measuring point and the detector. It has been verified by an experiment on a laminar jet ethylene-air diffusion flame. Being proportional to the attenuation, the ratio of LII signal at two different detection wavelengths can be used to correct the measured LIIsignal and obtain the unattenuated LII signal, from which the soot volume fraction in the flame can be estimated. Both the 1064-nm and frequency-doubled 532-nm beams from the Nd : YAG laser are used. Single-shot, one-dimensional(1-D) line images are recorded on the intensified CCD camera, with the rectangular-profile laser beam using 1-mm-diameter pinhole. Two broadband optical interference filters having the center wavelengths of 647 nm and 400 nm respectively and a bandwidth of 10 nm are used. This two-wavelength correction has been applied to the ethylene-air coannular laminar diffusion flame, previously studied on soot formation by the laser extinction method in this laboratory. The results by the LII measurement technique and the conventional laser extinction method at the height of 40 nm above the jet exit agreed well with each other except around outside of the peaks of soot concentration, where the soot concentration was relatively high and resulting attenuation of the LII signal was large. The radial profile shape of soot concentration was not changed a lot, but the absolute value of the soot volume fraction around outside edge changed from 4ppm to 6.5 ppm at r=2.8mm after correction. This means that the attenuation of LII signal was approximately 40% at this point, which is higher than the average attenuation rate of this flame, 10~15%.

• Journal of KIISE
• /
• v.43 no.4
• /
• pp.404-410
• /
• 2016

Automated road map generation poses significant research challenges since GPS-based navigation systems prevail in most general vehicles. This paper proposes an automated detecting method for intersection points using GPS vehicle trajectory data without any background digital map information. The proposed method exploits the fact that the trajectories are generally split into several branches at an intersection point. One problem in previous work on this intersection detecting is that those approaches require stopping points and direction changes for every testing vehicle. However our approach does not require such complex auxiliary information for intersection detecting. Our method is based on partial trajectory matching among trajectories since a set of incoming trajectories split other trajectory cluster branches at the intersection point. We tested our method on a real GPS data set with 1266 vehicles in Gangnam District, Seoul. Our experiment showed that the proposed method works well at some bigger intersection points in Gangnam. Our system scored 75% sensitivity and 78% specificity according to the test data. We believe that more GPS trajectory data would make our system more reliable and applicable in a practice.

• Speech Sciences
• /
• v.10 no.4
• /
• pp.117-124
• /
• 2003

Speaker recognition is the technology that confirms the identification of speaker by using the characteristic of speech. Such technique is classified into speaker identification and speaker verification: The first method discriminates the speaker from the preregistered group and recognize the word, the second verifies the speaker who claims the identification. This method that extracts the information of speaker from the speech and confirms the individual identification becomes one of the most efficient technology as the service via telephone network is popularized. Some problems, however, must be solved for the real application as follows; The first thing is concerning that the safe method is necessary to reject the imposter because the recognition is not performed for the only preregistered customer. The second thing is about the fact that the characteristic of speech is changed as time goes by, So this fact causes the severe degradation of recognition rate and the inconvenience of users as the number of times to utter the text increases. The last thing is relating to the fact that the common characteristic among speakers causes the wrong recognition result. The silence parts being included the center of speech cause that identification rate is decreased. In this paper, to make improvement, We proposed identification rate can be improved by removing silence part before processing identification algorithm. The methods detecting speech area are zero crossing rate, energy of signal detect end point and starting point of the speech and process DTW algorithm by using two methods in this paper. As a result, the proposed method is obtained about 3% of improved recognition rate compare with the conventional methods.

• Smart Structures and Systems
• /
• v.18 no.3
• /
• pp.405-423
• /
• 2016

In this study, the feasibility of using telecommunication single-mode optical fiber (SMF) as a distributed fiber optic strain and crack sensor was evaluated in concrete pavement monitoring. Tensile tests on various sensors indicated that the $SMF-28e^+$ fiber revealed linear elastic behavior to rupture at approximately 26 N load and 2.6% strain. Six full-scale concrete panels were prepared and tested under truck and three-point loads to quantify the performance of sensors with pulse pre-pump Brillouin optical time domain analysis (PPP-BOTDA). The sensors were protected by precast mortar from brutal action during concrete casting. Once air-cured for 2 hours after initial setting, half a mortar cylinder of 12 mm in diameter ensured that the protected sensors remained functional during and after concrete casting. The strains measured from PPP-BOTDA with a sensitivity coefficient of $5.43{\times}10^{-5}GHz/{\mu}{\varepsilon}$ were validated locally by commercial fiber Bragg grating (FBG) sensors. Unlike the point FBG sensors, the distributed PPP-BOTDA sensors can be utilized to effectively locate multiple cracks. Depending on their layout, the distributed sensors can provide one- or two-dimensional strain fields in pavement panels. The width of both micro and major cracks can be linearly related to the peak strain directly measured with the distributed fiber optic sensor.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.22 no.2
• /
• pp.179-188
• /
• 2012

Packing techniques, one of malicious code detection and analysis avoidance techniques, change code to reduce size and make analysts confused. Therefore, malwares have more time to spread out and it takes longer time to analyze them. Thus, these kind of unpacking techniques have been studied to deal with packed malicious code lately. Packed programs are unpacked during execution. When it is unpacked, the data inside of the packed program are changed. Because of these changes, the entropy value of packed program is changed. After unpacking, there will be no data changes; thus, the entropy value is not changed anymore. Therefore, packed programs could be unpacked finding the unpacking point using this characteristic regardless of packing algorithms. This paper suggests the generic unpacking mechanism using the method estimating the unpacking point through the variation of entropy values.

• Atmosphere
• /
• v.33 no.1
• /
• pp.1-20
• /
• 2023

Holding the longest observation data from April 1904, Busan is one of the essential points to understand the climate variability of the Korean Peninsula without missing data since implementing the modern weather observation of the South Korea. Busan is featured by coastal areas and affected by various climate factors and fluctuations. This study aims to investigate climate variability and changes in climatic variables, extremes, and several weather indexes. The statistically significant change points in daily mean rainfall intensity and temperature were found in 1964 and 1965. Based on the change point detection, 117 years were divided into two periods for daily mean rainfall intensity and temperature, respectively. In the long-term temperature analysis of Busan, the increasing trend of the daily maximum temperature during the period of 1965~2021 was larger than the daily mean temperature and the daily minimum temperature. Applying Ensemble Empirical Mode Decomposition, daily maximum temperature is largely affected by the decadal variability compared to the daily mean and minimum temperature. In addition, the trend of daily precipitation intensity from 1964~2021 shows a value of about 0.50 mm day^-1, suggesting that the rainfall intensity has increased compared to the preceding period. The results in extremes analysis demonstrate that return values of both extreme temperatures and precipitation show higher values in the latter than in the former period, indicating that the intensity of the current extreme phenomenon increases. For Wet-Bulb Globe Temperature (effective humidity), increasing (decreasing) trend is significant in Busan with the second (third)-largest change among four stations.

• The Transactions of the Korea Information Processing Society
• /
• v.5 no.11
• /
• pp.3010-3023
• /
• 1998

GA has a fast convergence speed in searching the one point around optimal value. But it's convergence time increase in searching the region around optimal value because it has no regional searching mechanism. BP has the tendency to converge the local minimum because it has global searching mechanism. To overcome these problems, a method in which a genetic algorithm and a back propagation are applied in turn is proposed in this paper. By using a genetic algorithm, we compute optimal synaptic strength and offset value. And then, these values are fed to the input of the back propagation. This proposed method is superior to each above method in improving the convergence speed.

• Proceedings of the KSR Conference
• /
• 2011.05a
• /
• pp.377-383
• /
• 2011

The paper is to perceive accurately speed of the train through redundant processor operation. When Slip/slide is occurred at the axle, the train is applied brake force using the Tachometer and the Doppler sensor which assistance equipment. One of the main features of railway signaling system is that rolling stock is made stop to avoid collision with the rolling stock ahead when the rolling stock exceeds its maximum operating speed in line. In addition, in the case of the rolling stock with automatic train operation, it carries out activities such as braking and propulsion using the difference between its actual speed and target speed at the point. To perform these functions, it is essential to calculate the exact speed of the rolling stock in signaling equipment on vehicles. Train speed detection unit are composed of the Tachometer and the Doppler sensor, and speed information is sent to the SDU unit. The processor of SDU unit calculates the speed of the train using compare logic the received speed information. Even if there are Slip/Slide, signaling system is available to apply exact braking, to improve stop on position and to guarantee the safety of trains.

• Journal of Environmental Impact Assessment
• /
• v.8 no.2
• /
• pp.73-82
• /
• 1999

This study analyzed the relationship between NDVI(Normalized Difference Vegetation Index) and urban heat island in three cities: Daegu, Kyungju, and Pohang for understanding the degree of nature conservation concentrating in the transition zone of them. Daegu city is the third city in Korea which has a dense population. Kyungju is a traditional city which has good nature. Pohang is an industrial city which has those of characters of Daegu and Kyungju. Landsat 1M data in May 17, 1997 were used for the analysis of heat island. There were about four theoretical models to estimate the surface temperature from TM data: Two-point linear model, Linear regression model, Quadratic regression model, and Cubic regression model. In this study, Linear regression model had been utilized to analyze the urban heat island. On the resultant images, the transition zone of Daegu was urbanized more extremely than those of other two cities. It is thought that the analysis of relationship between NDVI and surface temperature, used in this study, is regarded as one of effective methodologies for urban-environmental detection from satellite imageries.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.31 no.6_2
• /
• pp.611-623
• /
• 2013

Point cloud data (i.e., LiDAR; Light Detection and Ranging) collected by Airborne Laser Scanner (ALS) system is one of the major sources for surface reconstruction including DEM generation, topographic mapping and object modeling. Recently, demand and requirement of the accurate and realistic Digital Building Model (DBM) increase for geospatial platforms and spatial data infrastructure. The main issues in the object modeling such as building and city modeling are efficiency of the methodology and quality of the final products. Efficiency and quality are associated with automation and accuracy, respectively. However, these two factors are often opposite each other. This paper aims to introduce correction scheme of incorrectly determined Model Key Points (MKPs) regardless of the segmentation method. Planimetric and height locations of the MKPs were refined by surface patch fitting based on the Least-Squares Solution (LESS). The proposed methods were applied to the synthetic and real LiDAR data. Finally, the results were analyzed by comparing adjusted MKPs with the true building model data.