• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.6
• /
• pp.303-309
• /
• 2012

Energy expenditure values were estimated based on the voice signals and body activities. Voice signals and body activities were obtained using PVDF contact vibration sensor and 3-axis accelerometer, respectively. Vibration caused by voices, activity signals, and actual energy consumption were acquired using data acquisition system and gas analyzer. With the use of power values from the voice signals and weight as independent variables, R-square of 0.918 appeared to show the highest value. For activity outputs, use of signal vector magnitude, body mass index, height, and age as independent variables revealed to provide the highest correlation with actual energy expenditure. Estimation of energy expenditure based on voice and activity provides more accurate results than based on activity only.

• Journal of Astronomy and Space Sciences
• /
• v.29 no.1
• /
• pp.69-77
• /
• 2012

This report describes the inception, development and extensive use over 30 years of elliptical polarimeters at the University of Pennsylvania. The initial Mark I polarimeter design utilized oriented retarder plates and a calcite Foster-Clarke prism as the analyzer. The Mark I polarimeter was used on the Kitt Peak 0.9 m in 1969-70 to accomplish a survey of approximately 70 objects before the device was relocated to the 0.72 m reflector at the Flower and Cook Observatory. Successive generations of automation and improvements included the early-80's optical redesign to utilize a photoelastic modulated wave plate and an Ithaco lock-in amplifier-the photoelastic modulating polarimeter. The final design in 2000 concluded with a fully remote operable device. The legacy of the polarimetric programs includes studies of close binaries, pulsating hot stars, and luminous late-type variables.

• Smart Structures and Systems
• /
• v.8 no.1
• /
• pp.139-155
• /
• 2011

Polymeric thin-film assemblies whose bulk electrical conductivity and mechanical performance have been enhanced by single-walled carbon nanotubes are proposed for measuring strain and corrosion activity in metallic structural systems. Similar to the dermatological system found in animals, the proposed self-sensing thin-film assembly supports spatial strain and pH sensing via localized changes in electrical conductivity. Specifically, electrical impedance tomography (EIT) is used to create detailed mappings of film conductivity over its complete surface area using electrical measurements taken at the film boundary. While EIT is a powerful means of mapping the sensing skin's spatial response, it requires a data acquisition system capable of taking electrical impedance measurements on a large number of electrodes. A low-cost wireless impedance analyzer is proposed to fully automate EIT data acquisition. The key attribute of the device is a flexible sinusoidal waveform generator capable of generating regulated current signals with frequencies from near-DC to 20 MHz. Furthermore, a multiplexed sensing interface offers 32 addressable channels from which voltage measurements can be made. A wireless interface is included to eliminate the cumbersome wiring often required for data acquisition in a structure. The functionality of the wireless impedance analyzer is illustrated on an experimental setup with the system used for automated acquisition of electrical impedance measurements taken on the boundary of a bio-inspired sensing skin recently proposed for structural health monitoring.

• International Journal of Automotive Technology
• /
• v.7 no.4
• /
• pp.407-413
• /
• 2006

The liquefied petroleum gas(LPG), mixture of propane and butane, has the potential to reduce toxic hydrocarbon emissions and inhibit ozone formation due to its chemical composition. Conventional mixer systems, however, have problems in meeting the future lower emission standards because of the difficulty in controlling air-fuel ratio precisely according to mileage tar accumulation. Liquid Phase LPG injection(LPLi) system has several advantages in more precise fuel metering and higher engine performance than those of the conventional mixer type. On the other hands, leakage problem of LPLi system at the injector tip is a main obstacle for meeting more stringent future emission regulations because these phenomena might cause excessive amount of THC emission during cold and hot restart phase. The main focus of this paper is the development of a leaked fuel recirculation system, which can eliminate the leaked fuel at the intake system with the activated carbon canister. Leaked fuel level was evaluated by using a fast response THC analyzer and gas chromatography. The result shows that THC concentration during cold and hot restart stage decreases by over 60%, and recirculation system is an effective method to meet the SULEV standard of the LPLi engine.

• Journal of Biosystems Engineering
• /
• v.43 no.2
• /
• pp.94-102
• /
• 2018

Purpose: In this study, a maintenance free super-capacitor battery charging system based on the photovoltaic module, to be used in agricultural electric carriers, was developed and its charging characteristics were studied in detail. Methods: At first, the electric carrier system configuration is introduced and the electric control components are presented. The super-capacitor batteries and photovoltaic module used in the experiment are specified. Next, the developed charging system consisting of a constant current / constant voltage Buck converter as the charging device and a super-capacitor cell as a balancing device are initiated. The proposed circuit design, a developed PCB layout of each device and a proportional control to check the current and voltage during the charging process are outlined. An experiment was carried out using a developed prototype to clarify the effectiveness of the proposed system. A power analyzer was used to measure the current and voltage during charging to evaluate the efficiency of the energy storage device. Finally, the conclusions of this research are presented. Results: The experimental results show that the proposed system successfully controls the charging current and balances the battery voltage. The maximum voltage of the super-capacitor battery obtained by using the proposed battery charger is 16.2 V, and the maximum charging current is 20 A. It was found that the charging time was less than an hour through the duty ratio of 95% or more. Conclusions: The developed battery charging system was successfully implemented on the agricultural electric carriers.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.377-378
• /
• 2005

In this study, $SiO_2$ thin film was deposited on variable conditions of the RF power and working pressure by RF magnetron sputtering to apply to the Bragg reflector of the SMR type FBAR device. A crystal orientation and microstructure of $SiO_2$ thin film was studied by using the XRD, AFM and SEM. The best condition was obtained through analyzing the structural characteristics of thin film. Finally, FBAR device was fabricated with applying the best condition of $SiO_2$ thin film and the resonant characteristics was investigated by network analyzer to verify application possibility as a efficient device.

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.179-186
• /
• 2007

KTX control systems mutually control OBCS, ATC, MBU, TECA, MDT, ABU, HVAC, TRAE, PID and FDTR, KTX OBCS as master, and controls other sub-control devices as slave, using various serial lines. In order to analyze physical structure of various serial link lines and mutual data transmission structure, serial line analyzer is used in many ways. To use serial line analyzer, prior and professional technics about High Speed Train and experience of using device are necessary. In spite of difficult situation of space and environment where we work for maintenance of High Speed Train, in presenting basic structure about physical connection method aquired by sub-device serial line data collection and about communication data analysis, I hope that this research will be helpful for the person who work for similar area. Also, I hope that this research will help diagnostic work of High Speed Train, which is necessary for test run of independently developed High Speed Train.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.38 no.4 s.117
• /
• pp.68-75
• /
• 2006

Electromagnetic shielding sheet using the carbon and wood fiber mixture was manufactured in an effort to develop an electromagnetic shielding packaging material. Carbon fibers were cut into 5, 10, and 15 mm using the automatic cutting device and blown and dispersed using compression air passed through the fine nozzle. Then carbon fibers were slurried with water (0.1% consistency), and softwood kraft pulp along with cone starch were added. The wet mats were manufactured by dewatering in modified hand-sheet machine. The wet mats were pressed upto $4kgf/cm^2$ in the carbon and wood fiber mixture mat press. The wet mats were dried in the automatic controlled plate dryer. Investigation on the formation and surface structure of the newly developed carbon and wood fiber mixture electromagnetic shielding sheet were carried out using the scanning electron microscopy and the image analyzer. Finally electromagnetic shielding characteristics of the newly developed carbon and wood mixture sheet were measured using net-work analyser. The result was promising in the light of the fact that this method could open a new way to substitute the expensive imported electromagnetic shielding sheet.

• Journal of the Korea Society for Simulation
• /
• v.22 no.2
• /
• pp.21-31
• /
• 2013

There is a high demand for the diagnostic medical blood analyzer in the global medical device market. The domestic market is in infant stage, but expected to grow very fast. In this study, we attempt to provide several ways for production improvement in order to secure price competitiveness of domestic medical blood analyzer. For this purpose we identify the problems of current production process using ARENA simulation and suggest several alternatives for productivity improvement.. Five steps of TOC (Theory of Constraints) and ARENA simulation are employed to predict productivity of each alternative and to suggest further improvement.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.12
• /
• pp.2857-2863
• /
• 2014

IR-UWB has been developed as a standard of indoor ranging technology, because it has robust and good transmission characteristics in indoor environments and it can be operated with low power. In this paper, a IR-UWB packet analyzer is designed and implemented based on IEEE 802.15.4a, which is useful in developing IR-UWB real time location system with resolution of a few ten centimeters. A sniffer device of the packet analyzer monitors IR-UWB wireless networks, captures MAC packet frames, and transmits packet frames to the packet analyzing computer. The packet analyzing program in a computer analyzes received MAC packet frames and displays parsed packet information for developing engineers. Developed packet analyzer is used to analyze IEEE 802.15.4a MAC protocol, and also it can be used in other IEEE 802 series MAC protocol by modifying some functions.