• 한국근적외분광분석학회:학술대회논문집
• /
• 한국근적외분광분석학회 2001년도 NIR-2001
• /
• pp.1256-1256
• /
• 2001

The physico-chemical and texture characteristics of meat determine the nutritional, technological and sensory quality. However, the analysis of meat quality requires expensive, laborious and time consuming analytical methods. The objective of this study was to evaluate NIR spectroscopy using transmittance for determining the moisture, fat, protein and total pigment content, the water holding capacity (WHC) and the toughness of beef meat. A total of 318 spectra were recorded from ground beef samples by a Feed Analyzer 1265 of Infratec. The samples were obtained from the Longissimus muscle of the 10$^{th}$ rib of yearling bulls, ground with an electrical chopper, vacuum packaged, aged during 7 days and frozen at -24$^{\circ}C$ until the analyses were done. Moisture content was measured by oven drying at 10$0^{\circ}C$, fat content was determined by Soxhlet extraction and protein content was estimated from nitrogen content using the Kjeldahl analysis. The total pigment content was determined by the method of Hornsey and the WHC using the method of filter paper press. The instrumental evaluation of texture (maximum load WB, maximum stress MS and toughness) was conducted in an Instron equipment with a Warner-Bratzler shearing device. This analysis was performed on a chop of 3.5 cm obtained from the longissimus of the 8$^{th}$ rib, aged during 7 days, kept frozen at -24$^{\circ}C$ and cooked before the analysis. Near infrared spectra were recorded as log 1/T (T=transmittance) at 2 nm intervals from 850 to 1050 nm using a Feed Analyzer 1265 of Infratec. Calibrations were performed with the WinISI software (vs. 1.02) using the MPLS method. To examine the effect of scatter correction o. derivation of spectra on the calibration performance, calibrations were calculated with the crude spectra or pretreated with different mathematical treatments (inverse MSC, SNVD) and/or second derivative operation. For chemical composition, the use of the scatter corrections improved the calibration statistics, in terms of lower SECV and higher $r^2$. In most of the variables, the use of the 2$^{nd}$ derivative improved the predictions, mainly when combined with the SNVD treatment. However, for predicting the texture traits, the best estimation was obtained from the crude spectrum. These results showed that the equations obtained for predicting moisture, fat and total pigments were very accurate, with $r^2$ being higher that 0.9. However, the prediction of the texture traits (WB, MS, toughness) from ground meat was poor.

• 한국광학회지
• /
• 제15권4호
• /
• pp.375-384
• /
• 2004

Ti:LiNbO$_3$ 세 도파로형 광도파로와 CPW 진행파 전극으로 구성된 고속 외부 광변조기를 설계, 제작하였다. 결합모드 이론을 이용하여 세 도파로 광결합기의 스위칭 현상을 해석하였으며, 유한차분법을 이용하여 결합길이를 계산하였다. SOR에 의해 위상속도 및 특성 임피던스 정합 조건이 만족되도록 CPW 진행파 전극의 파라미터를 설계하였다. 제작된 소자의 dc 스위칭 및 전극의 RF 특성을 측정하였다. 제작된 세 도파로 광변조기의 삽입손실과 스위칭 전압은 약 4 dB와 15.6 V였다. RF 특성을 얻기 위하여 회로분석기(Network Analyzer)를 이용하여 진행파 전극의 S 파라미터를 측정하였다. 측정 결과 진행파 전극의 특성임피던스 Z$_{c}$=39.2$\Omega$, M/W(Microwave) 유효굴절률 N$_{eff}$=2.48, 그리고 감쇠상수 a$_{m}$ =0.0665/(equation omitted)등의 파라미터를 추출하였다. 추출된 진행파 전극 파라미터를 이용하여 이론적인 주파수 응답 R($\omega$)을 계산하였으며, 광 검출기로 측정된 주파수 응답 R($\omega$)과 비교하였다. 주파수 응답측정 결과, 3 dB 변조대역폭은 13 GHz로 측정되었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.341-341
• /
• 2012

Recently, oxide semi-conductor materials have been investigated as promising candidates replacing a-Si:H and poly-Si semiconductor because they have some advantages of a room-temperature process, low-cost, high performance and various applications in flexible and transparent electronics. Particularly, amorphous indium-gallium-zinc-oxide (a-IGZO) is an interesting semiconductor material for use in flexible thin film transistor (TFT) fabrication due to the high carrier mobility and low deposition temperatures. In this work, we demonstrated improvement of flexibility in IGZO TFTs, which were fabricated on polyimide (PI) substrate. At first, a thin poly-4vinyl phenol (PVP) layer was spin coated on PI substrate for making a smooth surface up to 0.3 nm, which was required to form high quality active layer. Then, Ni gate electrode of 100 nm was deposited on the bare PVP layer by e-beam evaporator using a shadow mask. The PVP and $Al_2O_3$ layers with different thicknesses were used for organic/inorganic multi gate dielectric, which were formed by spin coater and atomic layer deposition (ALD), respectively, at $200^{\circ}C$. 70 nm IGZO semiconductor layer and 70 nm Al source/drain electrodes were respectively deposited by RF magnetron sputter and thermal evaporator using shadow masks. Then, IGZO layer was annealed on a hotplate at $200^{\circ}C$ for 1 hour. Standard electrical characteristics of transistors were measured by a semiconductor parameter analyzer at room temperature in the dark and performance of devices then was also evaluated under static and dynamic mechanical deformation. The IGZO TFTs incorporating hybrid gate dielectrics showed a high flexibility compared to the device with single structural gate dielectrics. The effects of mechanical deformation on the TFT characteristics will be discussed in detail.

• Physical Therapy Rehabilitation Science
• /
• 제10권3호
• /
• pp.311-319
• /
• 2021

Objective: To investigate the effect of emphasized initial contact by using a wearable air-pressure insole to provide auditory-feedback with variations of maximum peak pressure (MPP) of the affected side on spatiotemporal gait parameters and gait symmetry of stroke patients Design: A cross-sectional study Methods: Eighteen stroke patients participated in this study. All subjects walked five trials using an air-pressure insole that provides auditory feedback with different thresholds set on the insole. First, subjects walked without any auditory feedback. Then, the MPP threshold on the affected side was set from 70% and increase threshold by 10% after each trial until 100%. They walked three times or more on the gait analyzer for each trial, and the average values were measured. Before starting the experiment, subjects measured body weight, initial gait abilities and affected side MPP without auditory feedback. Results: Temporal and spatial variables were significantly increased in trials with auditory feedback from air-pressure insole except for non-paralyzed single support time and spatial gait symmetry compared to trials without auditory feedback(p<0.05). Among the four different thresholds, the walking speed, unaffected side single support time, affected and unaffected side stride, and affected side step length were greatest at 80% threshold of maximum peak, while affected single support time, temporal gait symmetry, and unaffected step length were greatest at the maximum peak of 100% threshold. Conclusions: These results indicate that auditory feedback gait using air-pressure insoles can be an effective way to improve walking speed, single support time, step length, stride, and temporal gait symmetry in stroke patients.

• 마이크로전자및패키징학회지
• /
• 제28권3호
• /
• pp.1-7
• /
• 2021

본 논문에서는 Bare-die Chip 형태의 Drive amplifier를 Ajinomoto Build-up Film (ABF)와 FR-4로 구성된 PCB에 내장함으로써 28 GHz 대역 모듈에서 적용될 수 있는 내장형 능동소자 모듈을 구현하였다. 내장형 모듈에 사용된 유전체 ABF는 유전율 3.2, 유전손실 0.016의 특성을 가지고 있으며, Cavity가 형성되어 Drive amplifier가 내장되는 FR4는 유전율 3.5, 유전손실 0.02의 특성을 가진다. 제안된 내장형 Drive amplifier는 총 2가지 구조로 공정하였으며 측정을 통해 각각의 S-Parameter특성을 확인하였다. 공정을 진행한 2가지 구조는 Bare-die Chip의 패드가 위를 향하는 Face-up 내장 구조와 Bare-die Chip의 패드가 아래를 향하는 Face-down내장 구조이다. 구현한 내장형 모듈은 Taconic 사의 TLY-5A(유전율 2.17, 유전손실 0.0002)를 이용한 테스트 보드에 실장 하여 측정을 진행하였다. Face-down 구조로 내장한 모듈은 Face-up 구조에 비해 Bare-die chip의 RF signal패드에서부터 형성된 패턴까지의 배선 길이가 짧아 이득 성능이 좋을 것이라 예상하였지만, Bare-die chip에 위치한 Ground가 Through via를 통해 접지되는 만큼 Drive amplifier에 Ground가 확보되지 않아 발진이 발생한다는 것을 확인하였다. 반면 Bare-die chip의 G round가 부착되는 PCB의 패턴에 직접적으로 접지되는 Face-up 구조는 25 GHz에서부터 30 GHz까지 약 10 dB 이상의 안정적인 이득 특성을 냈으며 목표주파수 대역인 28 GHz에서의 이득은 12.32 dB이다. Face-up 구조로 내장한 모듈의 출력 특성은 신호 발생기와 신호분석기를 사용하여 측정하였다. 신호 발생기의 입력전력(P_in)을 -10 dBm에서 20 dBm까지 인가하여 측정하였을 때, 구현한 내장형 모듈의 이득압축점(P_1dB)는 20.38 dB으로 특성을 확인할 수 있었다. 측정을 통해 본 논문에서 사용한 Drive amplifier와 같은 Bare-die chip을 PCB에 내장할 때 Ground 접지 방식에 따라 발진이 개선된다는 것을 검증하였으며, 이를 통해 Chip Face-up 구조로 Drive amplifier를 내장한 모듈은 밀리미터파 대역의 통신 모듈에 충분히 적용될 수 있을 것이라고 판단된다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 춘계학술대회 논문집
• /
• pp.1445-1456
• /
• 2011

부산도시철도 추진장치를 종합 제어하는 Chopper Gate Control Unit는 다수의 전자 전기부품, PCB, 전원공급기, 게이트회로증폭기, 프레온가스냉각기, 보호회로 등으로 구성되어 있는 주요장치로서 일본 미씨비시에서 생산된 제품을 사용하고 있다. 최근에는 초퍼장치의 고장 및 시험기 에러가 자주 발생하여 원인분석 결과 Chopper Gate Control Unit內 LPF(Lower Pass Filter)의 장기사용(약25년)으로 인한 노후화와 성능저하가 주요 원인이었음을 밝혀내고 물품구매를 위해 제작사에 문의 하였으나 이미 생산이 중단된 제품으로 별도 주문 제작시에는 고가의 비용이 발생한다. LPF는 몰딩처리가 되어있는 부품으로 수선이 불가하여 자체기술력으로 연구 개발하여 현재 부산도시철도 1호선 전동차에 13set를 적용하여 운영하고 있다. 본 논문에서는 연산 증폭기(OP Amp)와 저항, 콘덴서 등의 조합으로 자체개발한 능동필터인 Active LPF의 특성분석, 회로해석 및 설계, 다기능분석기, 스펙트럼분석기, 오실로스코프 등을 이용한 파형특성과 PS Pice 시뮬레이션 시험결과 등 개발에 관한 연구내용을 다루었다.

• The Journal of Advanced Prosthodontics
• /
• 제3권4호
• /
• pp.196-203
• /
• 2011

PURPOSE. This study evaluated marginal fit of glass infiltrated alumina cores fabricated using two techniques and their marginal stability after firing cycles of veneering porcelain. MATERIALS AND METHODS. Fifteen standardized all-ceramic crowns were fabricated on a metal die using each technique: slip cast technique of VITA In-Ceram sprint Alumina (Group A as control) and plastic foil matrix technique of Turkom-Cera fused alumina core system (Group B). Copings were compared between groups and within groups at coping stage and after firing each layer of veneering porcelain. A device was used to standardize seating of copings on the metal die and positioning of the specimens under the microscope after each stage of fabrication. The specimens were not cemented and marginal gap was measured using an image analyzing software (Imagepro Express) on the photographs captured under an optical microscope. Two tailed unpaired 't test' was used to compare marginal gaps in two groups and one way ANOVA was used to analyze marginal distortion within each group at 95% confidence interval. RESULTS. The marginal gap was smaller at the coping stage in group B ($60+30{\mu}M$) than group A ($81+21{\mu}M$) with statistical significance. After firing of veneering porcelain the difference was insignificant. At the final stage, both groups exhibited lower mean marginal gaps than at the initial coping stage with the difference of $11.75{\mu}M$ for group A and $11.94{\mu}M$ for group B, but it was statistically insignificant due to high value of standard deviation. CONCLUSION. Within the limitations of this study, it was concluded that both techniques produced copings with comparable and acceptable marginal fit and marginal stability on firing veneering porcelain.

• 한국정보처리학회논문지
• /
• 제1권2호
• /
• pp.263-271
• /
• 1994

제조장치의 네트워크 환경은 PLC, 로보트와 같은 프로그래머블디바이스에 Mini- MAP 네트워크 접속장치를 장착하여 원격제어가 가능한 공정한 네트워크 시스템 구성 이 연구되고 있다. 본 논문에서 설계된 공정 네트워크 접속장치는 MAP 3.0 규격을 근거로 MAC부 계층은 TBC(token bus controller)가 수행하고, LLC부 계층은 class 3으로, 응용계층은 MMS(manufacturing message standard)를 기본으로 설계하였다. 구현된 소프트웨어는 Mini-MAP의 실시간 정보 전송 성능을 보존하기 위하여 C Exec. 의 real-time executive를 기반으로 설계하여 firmware로 탑재하였다. 본 접속장치는 군관리 공정 모델에서 시험 운영하였으며, LLC 계층의 오류검출과 전송기능은 프로토 콜 분석기를 이용하여 확인하였으며, MMS는 적합성 시험을 이미 받은 MMS를 탑재한 상용제품과의 통신운영을 통하여 적합성 시험을 확인하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 춘계학술대회 논문집 반도체 재료 센서 박막재료 전자세라믹스
• /
• pp.157-160
• /
• 2004

Ferroelectric $(Ba_xSr_{1-x})TiO_3$ (BST) thin films have been deposited on (001) MgO single crystals by a pulsed laser deposition (PLD) method. The structure of deposited BST thin films were investigated by an x-ray diffractometer. Calculated c-axis lattice parameters of the BST films exhibit a strong lattice distortion, which was not observed in ceramic BST at room temperature. This lattice distortion of BST has been attributed to strains caused by lattice constant difference between film and substrate, oxygen vacancies in BST film, and thermal expansion difference between film and substrate. Ferroelectric properties at 10 GHz have been measured using a HP 8510C vector network analyzer. Dielectric properties, capacitance tunability and quality factor, of the interdigitaed capacitors fabricated on BST films were calculated from the measured s-parameters. Two distinct behaviors in structural, opitical, and microwave properties of BST films were observed; below and above 200 mTorr of oxygen pressure in the deposition chmber.

• 대한디지털의료영상학회논문지
• /
• 제8권1호
• /
• pp.21-26
• /
• 2006

Hospitals these days are trying to introduce the a practice has recently been generalized in the test or diagnosis process, where test results and images from different test labs are interlinked together. This process is identical to that of physical aspect in EMR process, which computerizes the paper results within the hospital. One of the prerequisites for the process of computerizing test results is the interface between clinical test devices in the test labs. However, due to the variety of prescription inputs, disparity of test result papers, complexity of job in test labs and diversify of interfaces among the different devices, interconnection with the hospital information system is a complicated job. A universal control of clinical test devices which have independent communication protocols has become possible by connecting them with an interface workstation. As for the patients, waiting time for test has been reduced, and, thanks to the synchronized result retrieval system, it has become possible to check the test results on the very day of the test. As a result, the length of hospitalization has been reduced, too. In terms of workflow, as the transfer of charts and transfer of result papers are separated, the embarrassing job of collecting result papers has disappeared. As patients' test appointment and the results processing can be made on-line, extra work for doctors have disappeared. And, thanks to the computerization of test results information management, the job of statistical processing has become convenient.