• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.10 no.5
• /
• pp.1-13
• /
• 2011

Recently, a number of OBU(On Board Unit) have being spreaded since ETCS(Electronic Toll Collection System)using DSRC(Dedicated Short Range Communication) was installed in the tollgate of the whole country. Many R&D and commercialization related to ITS service using DSRC and OBU mentioned above are ongoing such as traffic information collection and provision and a signal control, and public traffic information and management and so on. Especially, there are many researches conducted(conducting) on traffic information collection and provision using communication between OBU and RSE. However, Standards for both DSRC application and traffic collection and provision are not established clearly yet. So we would like to suggest a method of traffic information collection and provision without changing of standard related to DSRC. This method is to put the traffic messages into the existing Action primitive for ETC, which is described on "Technical criterion IV of basic traffic information exchange" which was notified by Ministry of Land, Transport and Maritime Affairs. Proposed standard application method is applied both to RSE and OBE. It is the same system which ETCS used in highway, currently. We confirmed the efficiency and performance of the system through conducting a variety of driving test using 4 vehicles in real road condition. Result of the real road test shows the effectiveness and validity of this method with about 97% communication success rate and based on studying the cases of 3% communication failure, we can analyse the expected problems in traffic information collection and provision using this method.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.48 no.6
• /
• pp.41-50
• /
• 2011

This article is concerned with the technology to provide car driver the car's status which are composed of car trouble code in car engine and many sensors. In addition, it installs vehicle diagnostic programs on wireless communication's portable device, for example, Smart phone, PDA, PMP, UMPC. As a result, this is to provide car manager with many information of car sensors when we go to car maintenance. it can monitor relevant information on vehicle by portable device in real time, alert drivers with specific messages and also enable them to address abnormalities immediately. Moreover, the technology could help the drivers who perhaps don't know very well about their vehicles to drive safely and economically as well; the reason is because the whole system is composed of just Vehicle-information collecting device and personal wireless communication's portables and transfers the relating data to server computers through wireless network in order to handle information on vehicles. This technology make us monitor vehicle's running, failure and disorder by using wireless communication's portable device. Finally, this study system is composed of a lot of application to display us the car's status which get car's inner sensor information while driving a car.

• The Journal of the Korea Contents Association
• /
• v.9 no.12
• /
• pp.742-749
• /
• 2009

The use of cone-beam computed tomography(CBCT) has been proposed for guiding the delivery of radiation therapy. A kilovoltage imaging system capable of radiography, fluoroscopy, and cone-beam computed tomography(CT) has been integrated with a medical linear accelerator. A standard clinical linear accelerator, operating in arc therapy mode, and an amorphous-silicon (a-Si) with an on-board electronic portal imager can be used to treat palliative patient and verify the patient's position prior to treatment. On-board CBCT images are used to generate patient geometric models to assist patient setup. The image data can also, potentially, be used for dose reconstruction in combination with the fluence maps from treatment plan. In this study, the accuracy of Hounsfield Units of CBCT images as well as the accuracy of dose calculations based on CBCT images of a phantom and compared the results with those of using CT simulator images. Phantom and patient studies were carried out to evaluate the achievable accuracy in using CBCT and CT stimulator for dose calculation. Relative electron density as a function of HU was obtained for both planning CT stimulator and CBCT using a Catphan-600 (The Phantom Laboratory, USA) calibration phantom. A clinical treatment planning system was employed for CT stimulator and CBCT based dose calculations and subsequent comparisons. The dosimetric consequence as the result of HU variation in CBCT was evaluated by comparing MU/cCy. The differences were about 2.7% (3-4MU/100cGy) in phantom and 2.5% (1-3MU/100cGy) in patients. The difference in HU values in Catphan was small. However, the magnitude of scatter and artifacts in CBCT images are affected by limitation of detector's FOV and patient's involuntary motions. CBCT images included scatters and artifacts due to In addition to guide the patient setup process, CBCT data acquired prior to the treatment be used to recalculate or verify the treatment plan based on the patient anatomy of the treatment area. And the CBCT has potential to become a very useful tool for on-line ART.)

• Proceedings of the Korea Contents Association Conference
• /
• 2009.05a
• /
• pp.1159-1166
• /
• 2009

The use of cone-beam computed tomography(CBCT) has been proposed for guiding the delivery of radiation therapy. A kilovoltage imaging system capable of radiography, fluoroscopy, and cone-beam computed tomography(CT) has been integrated with a medical linear accelerator. A standard clinical linear accelerator, operating in arc therapy mode, and an amorphous-silicon (a-Si) with an on-board electronic portal imager can be used to treat palliative patient and verify the patient's position prior to treatment. On-board CBCT images are used to generate patient geometric models to assist patient setup. The image data can also, potentially, be used for dose reconstruction in combination with the fluence maps from treatment plan. In this study, the accuracy of Hounsfield Units of CBCT images as well as the accuracy of dose calculations based on CBCT images of a phantom and compared the results with those of using CT simulator images. Phantom and patient studies were carried out to evaluate the achievable accuracy in using CBCT and CT stimulator for dose calculation. Relative electron density as a function of HU was obtained for both planning CT stimulator and CBCT using a Catphan-600 (The Phantom Laboratory, USA) calibration phantom. A clinical treatment planning system was employed for CT stimulator and CBCT based dose calculations and subsequent comparisons. The dosimetric consequence as the result of HU variation in CBCT was evaluated by comparing MU/cCy. The differences were about 2.7% (3-4MU/100cGy) in phantom and 2.5% (1-3MU/100cGy) in patients. The difference in HU values in Catphan was small. However, the magnitude of scatter and artifacts in CBCT images are affected by limitation of detector's FOV and patient's involuntary motions. CBCT images included scatters and artifacts due to In addition to guide the patient setup process, CBCT data acquired prior to the treatment be used to recalculate or verify the treatment plan based on the patient anatomy of the treatment area. And the CBCT has potential to become a very useful tool for on-line ART.)

• Journal of Radiation Protection and Research
• /
• v.28 no.3
• /
• pp.255-261
• /
• 2003

An environmental radiation monitoring system based on high pressurized ionization chamber has been used for on-line gamma monitoring surrounding the KAERI (Korea Atomic Energy Research Institute), which transmits the dose data measured from ion chamber on the site via radio frequency to a central processing computer and stores the transmitted real-time data. Although communication using radio frequency has several advantages such as effective and economical transmission, storage, and data process, there is one main disadvantage that data loss during transmission often happens because of unexpected communication problems. It is possible to restore the loss data by off-line such as floppy disk but the simultaneous process and display of current data as well as the backup data are very difficult in the present on-line system. In this work, a new electronic circuit board and the operation software applicable to the conventional environmental radiation monitoring system are developed and the automatical synchronization of the ion chamber unit and the central processing computer is carried out every day. This system is automatically able to restore the backup data within 34 hours without additional equipments and also display together the current data as well as the transmitted backup data after checking time flag.

• Journal of Korean Society of Forest Science
• /
• v.104 no.2
• /
• pp.267-276
• /
• 2015

This study suggests a macroscopic method of evaluating forest recreation function based on physical characteristics of forests. The method was verified by a correlation between forest recreation function in popular top 45 mountains and popularity among them, with using data-mountain area, height, distance between mountain and cities, population around mountain, and size of public service. According to analysis of the forest recreation function, it is shown that top 8 mountains, including Jirisan and Seoraksan, provide over 64% of total recreation function, while they serve the function relatively lower than mountains near mega cities-Bukhansan in Seoul-do, in terms of the function per unit area ($km^2$). It is because, in a case of national and provincial mountains, the size of mountain is likely a critical factor for determining recreation function and the distance influences on it relatively lower. These findings implicate that a large size of forests bring the recreation function to visitors on nationwide level, whileas forests in suburban provide intensively it to near population to near population.

• Radiation Oncology Journal
• /
• v.27 no.1
• /
• pp.42-48
• /
• 2009

Purpose: The introduction of image guided radiation therapy/four-dimensional radiation therapy (IGRT/4DRT) potentially increases the accumulated dose to patients from imaging and verification processes as compared to conventional practice. It is therefore essential to investigate the level of the imaging dose to patients when IGRT/4DRT devices are installed. The imaging dose level was monitored and was compared with the use of pre-IGRT practice. Materials and Methods: A four-dimensional CT (4DCT) unit (GE, Ultra Light Speed 16), a simulator (Varian Acuity) and Varian IX unit with an on-board imager (OBI) and cone beam CT (CBCT) were installed. The surface doses to a RANDO phantom (The Phantom Laboratory, Salem, NY USA) were measured with the newly installed devices and with pre-existing devices including a single slice CT scanner (GE, Light Speed), a simulator (Varian Ximatron) and L-gram linear accelerator (Varian, 2100C Linac). The surface doses were measured using thermo luminescent dosimeters (TLDs) at eight sites-the brain, eye, thyroid, chest, abdomen, ovary, prostate and pelvis. Results: Compared to imaging with the use of single slice non-gated CT, the use of 4DCT imaging increased the dose to the chest and abdomen approximately ten-fold ($1.74{\pm}0.34$ cGy versus $23.23{\pm}3.67$cGy). Imaging doses with the use of the Acuity simulator were smaller than doses with the use of the Ximatron simulator, which were $0.91{\pm}0.89$ cGy versus $6.77{\pm}3.56$ cGy, respectively. The dose with the use of the electronic portal imaging device (EPID; Varian IX unit) was approximately 50% of the dose with the use of the L-gram linear accelerator ($1.83{\pm}0.36$ cGy versus $3.80{\pm}1.67$ cGy). The dose from the OBI for fluoroscopy and low-dose mode CBCT were $0.97{\pm}0.34$ cGy and $2.3{\pm}0.67$ cGy, respectively. Conclusion: The use of 4DCT is the major source of an increase of the radiation (imaging) dose to patients. OBI and CBCT doses were small, but the accumulated dose associated with everyday verification need to be considered.

• Applied Chemistry for Engineering
• /
• v.16 no.5
• /
• pp.620-627
• /
• 2005

In this study, life cycle assessment (LCA) on one of corrugated cardboard box as functional unit was carried out. System boundary of this study divided according to raw material acquisition, corrugated cardboard manufacture and corrugated cardboard box manufacture stage. And environmental impacts are evaluated on each stage and sub-process. The impact categories are classified into eight categories of abiotic resource depletion, global warming stratospheric ozone depletion, photochemical oxidant creation, air acidification, eutrophication, ecotoxicity and human toxicity. From the results, it is found that environment impacts at raw material acquisition stage is the highest as about 92% of whole stage due to liner board manufacture stage. The highest environmental impacts at sub-process of corrugated cardboard and box manufacture stage is a single facer and D/W backer process that included as main process in corrugated cardboard manufacture, and is caused by used energies like electricity, B-C oil, and etc. And then diagnosis for clean production process system of package is carried out. Through diagnosis, on loss rate is reduced and inner pressure intensity of box is improved. After improvement, environmental impact was decreased about 3.8% compared with before improvement.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.38 no.3
• /
• pp.249-255
• /
• 2002

This paper describes on the extraction of ship's real-time movement information using a combination full-function ARPA radar and ECS system that displays radar images and an electronic chart together on a single PC screen. The radar target extractor(RTX) board, developed by Marine Electronics Corporation of Korea, receives radar video, trigger, antenna bearing pulse and heading pulse signals from a radar unit and processes these signals to extract target information. The target data extracted from each pulse repetition interval in DSPs of RTX that installed in 16 bit ISA slot of a IBM PC compatible computer is formatted into a series of radar target messages. These messages are then transmitted to the host PC and displayed on a single screen. The position data of target in range and azimuth direction are stored and used for determining the center of the distributed target by arithmetic averaging after the detection of the target end. In this system, the electronic chart or radar screens can be displayed separately or simulaneously and in radar mode all information of radar targets can be recorded and replayed In spite of a PC based radar system, all essential information required for safe and efficient navigation of ship can be provided.

• Journal of Korean Society of Forest Science
• /
• v.76 no.3
• /
• pp.249-255
• /
• 1987

Forestry as with all land matters, under the Constitution, is a State matter. Thus the States, numbering 14, have considerable autonomy in decisions on forestry and related matters. However, the Federal Government, having jurisdiction over such issues as defence, education and research, endeavours to coordinate, standardise and advise the States on matters where the States have jurisdiction. However, forestry being a major revenue earner, is jealously guarded by the States. Under such circumstances and recognising the interdependencies of impacts of decisions at the State level, the institutional organisations play an important role in coordinating state activities to ensure that the benefits to the country as a whole are not sacrificed in favour of interests of individual state. Various legislative mechanisms have been established to ensure this coordinated effort. A National Forestry Council forms the apex of national political coordination. The Federal Forestry Department is responsible for coordination of developmental activities at the State level, which are implemented be the State Forestry Departments within Peninsular Malaysia. Research is carried out centrally by the Forest Research Institute of Malaysia(FRIM), a statutory body formed in 1985 from a research division of the Forestry Department. The Stares of Sabah and Sarawak have their own Forestry Departments, independent of the Federal Department, and each with its own research unit independent of FRIM. Tertiary education in forestry is the sole responsibility of the Agricultural University at Serdang with a campus for Diploma level training in Sarawak. In the developmental area in the State of Sabah, institutions have been formed to focus on specific areas of activities. The Sabah Foundation is responsible for the long term development of the State forests with a concession of about one million ha. Sabah Forest Development Authority(SAFODA) was formed to carry out reforestation of denuded areas. Sabah Forest Industries Ltd.(SFI) is responsible for the country's only integrated pulp and paper industry with its own afforestation program to support its resource supply. In Peninsular Malaysia various states have established State Corporations to manage large "sustained yield" concessions. While wildlife and state parks are managed by the respective forestry departments in Sabah and Sarawak, it is the responsibility of a separate department in Peninsula Malaysia called the Department of Wildlife and National Parks(under the Ministry of Science, Technology and Environment). Timber trade legislation and promotion in the Peninsular is the responsibility of the Malaysian Timber Industries Board(MTIB) for Peninsular Malaysia and the Sarawak Timber Industries Development Corporation(STIDC) in Sarawak. In the area of NGOs ; the Institute of Foresters Malaysia, is the professional body of forestry in the country. A Malaysian Forestry Society caters for the public participation and interest. Other environmentally related NGOs such as the Malayan Nature Society, the Environmental Protection Society, World Wildlife Fund, Friends of the Earth and the Consumers Associations also involve themselves in specific forestry activities. A number of timber trade associations are also formed by the private sector to assist the industries.