• Tribology and Lubricants
• /
• 제11권1호
• /
• pp.58-65
• /
• 1995

When marine lubricating oil began to be emulsified and oxidized through ingressive water that have leaked from cooling pump seal systems, cooler, purifier system and piping system, the cavitation erosion-corrosion in alloy metals of bearings remains to the various troublesome problem at effective engine performance. Therefore, applied the cathodic protection to the control test of cavitation erosion-corrosion, and appointed the marine system oil containing 3% sea water as test environments, with different conductibility. Also, used the piezoelectric vibrator with 20 KHz, 24 $\mu$m as the cavity generation apparatus, and examined the weight loss, potential value, current density etc. in specimens with those condition. According to this testing data, investigated influence of cathodic protection on the control characteristics of cavitation erosion-corrosion, and will serve those as an elementary design data of marine bearing.

• 한국신뢰성학회:학술대회논문집
• /
• 한국신뢰성학회 2011년도 춘계학술발표대회 논문집
• /
• pp.265-270
• /
• 2011

This paper describes a reliability/durability test of the remanufactured steering gear units. There used to be government restrictions to remanufacture certain types of automotive components regarding safety of passengers. Nevertheless, scientific approach to sustainability and remanufacturing process provided solid evidence of highly beneficial sides of reusing the products. Failure mode analysis of the steering gear unit is performed and main failure is found out. The unit is remanufactured by fixing the failure and its quality is assessed through designing a new sequence of loading events. Oil leakage is witnessed as a possible failure and its volume is measured. Conclusions based on laboratory condition durability test are given at the end.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1999년도 제30회 추계학술대회
• /
• pp.179-183
• /
• 1999

Rubbing occurs when a rotating element comes in contact with a stationary element. In the steam turbines, the rotating element is the rotor while the stationary elements are usually the oil deflectors and packing seals. Rubbing phenomenon may be often obseued on a new or rebuilt machine rather than on a machine that has been operating for several months or years. Rubbing in the turbine has been classified into two modes by the operating conditions: 1) start up or shut down, 2) steady state. At start up or shut down operation, rubbing produces synchronous whirl vibration, which are caused by thermal bow of the shaft due to localized heating on the shaft surface. While subsynchronous whirl vibration is caused by partial rubbing during the steady state operation. In this paper, the two case studies of troubleshooting for excessive vibration caused by rubbing in the actual steam turbines are investigated.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1996년도 제24회 춘계학술대회
• /
• pp.145-152
• /
• 1996

This paper deals with an experimental study on the f~iction torque characteristics of magnctic fluid seals for various oil temperatures, rotating speeds, and vacuum pressures. The friction torque of MFS was measured by high response torque meter. The experimental results show that, as the rotating speed increases, the fi'iction torque of MFS increases and as the oil temperature increases, the friction torque of MFS decreases. Also, the experimental results show that the friction torque of Model II is 1.73 ~ 2.56, 2.0 ~ 2.89, 2.0 - 3.25 times larger than those of Model I under the atmospheric pressure, vacuum pressure(10$^{-4}$ and 10$^{-6}$ torr), respectively.

• 한국수소및신에너지학회논문집
• /
• 제31권5호
• /
• pp.453-458
• /
• 2020

In this study, ethylene-propylene-diene monomer (EPDM) rubbers reinforced with various particle size of carbon black were prepared and tested. We followed recently published CSA/ANSI CHMC2 standard "the test methods for evaluating material compatibility in compressed hydrogen applications-polyemr". Measurement of change in hardness, tensile strength and volume were performed after exposure to maximum operating pressure, 87.5 MPa, for 168 hours (1 week). Once EPDM was exposed to high-pressure hydrogen, the samples experience volume increase and degradation of the physical properties. Also, after the dissolved hydrogen was fully eliminated from the specimens, the hardness and the tensile properties were not recovered. The rubber reinforced with smaller sizes of carbon black particles showed less volume expansion and decrease of physical properties. As a result, smaller particle size of carbon black filler led to more resistance to high-pressure hydrogen.

• Advances in Energy Research
• /
• 제6권1호
• /
• pp.75-90
• /
• 2019

Anthropogenic greenhouse gas emissions are rising rapidly despite efforts to curb release of such gases. One long term potential solution to offset these destructive emissions is the capture and storage of carbon dioxide. Partially depleted hydrocarbon reservoirs are attractive targets for permanent carbon dioxide disposal due to proven storage capacity and seal integrity, existing infrastructure. Optimum well completion design in depleted reservoirs requires understanding of prominent geomechanics issues with regard to rock-fluid interaction effects. Geomechanics plays a crucial role in the selection, design and operation of a storage facility and can improve the engineering performance, maintain safety and minimize environmental impact. In this paper, an integrated geomechanics workflow to evaluate reservoir caprock integrity is presented. This method integrates a reservoir simulation that typically computes variation in the reservoir pressure and temperature with geomechanical simulation which calculates variation in stresses. Coupling between these simulation modules is performed iteratively which in each simulation cycle, time dependent reservoir pressure and temperature obtained from three dimensional compositional reservoir models in ECLIPSE were transferred into finite element reservoir geomechanical models in ABAQUS and new porosity and permeability are obtained using volumetric strains for the next analysis step. Finally, efficiency of this approach is demonstrated through a case study of oil production and subsequent carbon storage in an oil reservoir. The methodology and overall workflow presented in this paper are expected to assist engineers with geomechanical assessments for reservoir optimum production and gas injection design for both natural gas and carbon dioxide storage in depleted reservoirs.

• 공업화학
• /
• 제22권2호
• /
• pp.149-154
• /
• 2011

연료전지 스택 작동환경에서의 열노화 특성을 살펴보기 위하여 다양한 고무 compound의 내열 및 압축 영구 줄음률의 평가를 실시하고, 스택의 장시간 운전을 통해 접합할 수 있는 대상액인 $H_2SO_4$, $H_2O$, LLC (Ethylene glycol : $H_2O=50:50$)에 대하여 장시간 평가를 실시하였다. NBR과 EPDM은 시간이 경과할수록 침적액의 변색하는 것을 알 수 있었으며, VMQ는 $H_2SO_4$ 분위기에서 시간에 따라 고무가 노화되는 것을 TGA, SEM, EDS 분석을 통하여 확인하였다.

• 한국환경보건학회지
• /
• 제27권2호
• /
• pp.30-36
• /
• 2001

This review begins with a brief expression of aerosol capture mechanism of fibrous filter(s) and performance of particulate removing respirators. The more complicated and detailed discussion is not included in this articles. Filtration efficiency and pressure drop are introduced as quality factor ( $q_{F}$) and the way in which filtration efficiency varies with particle size is discussed. Quality factors fro filters recently certified in USA were found to be very higher than those of filters made in Korea, China and USA filters certified with old certified standards. Electrically charged filters are widely used because they have high filtration efficiency and low pressure drop, but their efficiency decreases sharply at the condition occurring wet and oil mist. A discussion is given of respirator leakage through face seal and filter media with fit testing and total inward leakage testing. Since fit factor (FF) refers to the reciprocal of the fraction of the total air entering a respirator through face seal leakage , the degree of fitting performance for respirators is expected with FF. Because respirators made in Korea had generally lower FFs than respirators made in USA, it is necessary to develope respirators that fit properly for Koreans or establish regulations for fit testing.g.

• Elastomers and Composites
• /
• 제42권3호
• /
• pp.159-167
• /
• 2007

산업기계에서 공기압 또는 유압용 액추에이터(actuator)가 넓이 사용되는데 액추에이터의 중요 부품으로 탄성중합체로 만들어진 시일을 사용한다. 우수한 밀봉특성을 요구하는 시일의 재료로 내유성과 내마모성이 비교적 우수한 NBR(nitrile butadiene rubber) 재료가 가장 많이 사용한다. 산업기계의 액추에이터는 적용환경에 따라 낮거나 혹은 높은 온도에서 사용되는데 여러 온도에서 NBR은 그에 따른 특성이 다르게 나타난다. 본 연구에서는 새롭게 만들어지고 있는 재료 중 공기압, 유압용 시일(Seal)재료로 사용하는 Hs70, 80, 90등 3종의 NBR을 각각 $-10^{\circ}C,\;20^{\circ}C,\;80^{\circ}C,\;100^{\circ}C$온도에서 소재의 비선형(nonlinear) 특성의 시험과 유한요소해석에 필요한 재료상수를 알아보고 각각의 온도에서 하중 반복조건에 따른 소성변형 경향을 살펴보았다.

• 대한기계학회논문집A
• /
• 제37권2호
• /
• pp.241-248
• /
• 2013

본 논문에서는 상용 회전체 동역학 해석 툴을 이용하여 경사 운전조건을 고려한 대용량 추진 전동기용 베어링 개발에 상사적 설계 방법과 실험적 방법을 적용하였다. 개발된 베어링은 전기적으로 절연이 되어있으며 각 연결부는 2~4mm 의 에폭시 절연판을 연결하여 낮은 열전도 특성을 가지도록 하였다. 본 연구에서는 기존의 저속운전에서 야기되는 베어링 손상 문제를 해결하기 위해 원활한 유막이 생성될 수 있도록 고안한 정압 윤활장치를 적용하여 우수한 윤활특성을 확보하였다. 또한 대형 중량물에 대한 유지보수를 고려하여 반분할 방식의 조립구조를 적용하였다. 본 논문은 고부하, 저속 운전의 추진 전동기 분야에 사용되는 미끄럼 베어링의 주요 핵심설계요소를 언급하였다. 게다가, 시험벤치상에서 다양한 경사조건을 통해 실링부의 오일누유 현상을 확인하였다.