• Journal of the Korean Society of Safety
• /
• v.20 no.2 s.70
• /
• pp.44-49
• /
• 2005

Real-scale experimental study was performed to characterize the surface flame propagating velocity along the OF cable in the underground utility fire. Temperatures of oil filled OF cable and dried OF cable with the diameter of 90mn were measured using thermocouple and data log system. The hexane and alkyl-benzene oil were used as a fire source using the ignition device. As a result while the surface flame propagating velocity of the three cables was $0.06\~0.09cm/s$, the surface flame propagating velocity of the one cable was $0.028\~0.032cm/s$. Therefore, it was found that the surface propagating flame velocity of the three OF cables is $2.1\~2.8times$ faster than that of one OF cable case. The results show that the surface propagating flame velocity became larger as increase of the number of cable, the volume of alkyl-benzene oil in the cable. The characteristics of surface propagating flame velocity in the OF cable can be helpful to fire suppression system in utility.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.11
• /
• pp.2011-2014
• /
• 2008

We measured the permittivity and electromagnetic wave propagation velocity of used insulation oil with wide frequency range including ultra-high frequency by time domain reflectometry. The permittivity or propagation velocity is essential for locating discharge faults of oil filled power transformer. We derived 2.21 as a permittivity and $2.03{\times}10^8 m/s$ as a velocity from the measurement of pulse travelling time along a coaxial line filled with used insulation oil or air. The permittivity measurement system we designed shows high measurement accuracy and the convenience for field use.

• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.772-776
• /
• 2001

The flow structures of turbulent shear layer behind oil fences with different tip configurations were investigated experimentally using flow visualization and PIV velocity field measurement. An oil fence was installed in a circulating water channel and the flow structure around the fence tip was mainly analyzed in this experiment. The four tip configurations tested in this experiment are knife edge; semi-circle edge, circular edge and rectangular edge. The 300 instantaneous velocity fields were measured using the single-frame PIV system and they were ensemble averaged to give the mean velocity field and spatial distribution of turbulent statistics. Free stream velocity was fixed at 10ms/sec and the corresponding Reynolds number based on the fence height was Re=4000. As a result, for the oil fence with rectangular edge, the streamwise velocity component was decreased. On the other hand it was increased for the oil fence with circular edge. For all four fences tested in this study, general flow pattern of the lower shear layer is analogous but the upper layer shows difference depending on the tip configurations. The oil fence with circular edge has more diffusive upper shear layer than that of the others. The shear layer of the oil fence with rectangular edge has relatively thin thickness. The oil fence with circular edge was found to be proper shape for tandem fence.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.4
• /
• pp.578-587
• /
• 2009

In this paper, the characteristics of incompressible flow in a tube type marine fuel oil filter have been investigated. Fluent program has been used to obtain the solutions for the problems of three-dimensional, turbulent fuel oil flow in a filtering system. The inlet flow field is assumed to be uniform. The velocity and pressure distributions were obtained using Darcy's law. The increase of inlet velocity for cleaning fuel oil may cause some problems like vibration of the filter element. It was also required to consider the distribution of cleaning velocity because the worst distribution of cleaning velocity may cause the local insufficient cleaning effect and furthermore the effective filtration area can be reduced. The simulated results show that the computer code can be successfully applied for simulation of the complex base oil flow through the porous media. This paper could be applied to the design of auto-backwashing filtering system as design factor.

• Electrical & Electronic Materials
• /
• v.10 no.4
• /
• pp.334-341
• /
• 1997

Streaming electrification on insulating paper and pressboard under D.C. and A.C. electric field was investigated by using paper tubes and oil circulation apparatus. At first, flowing of static charges as measured with no electric field. As the temperature of oil increased, the measured current curve hows peak. As the velocity increased, it shows increasing exponential curve. Then, we applied A.C. and D.C. electric field on paper tube and the current from relaxation tank to earth was measured, which other factors such as temperature and velocity were varied like case of no electric field. The ions in oil carry the charges. So electric field makes asymmetry effect, and electrophoretic effect on ions in oil. We find that as the electric field intensity increased, the charges which were made by electric double layer were increased. The charge vs. velocity curve made peak point at a velocity.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.2
• /
• pp.114-119
• /
• 2016

This paper dealt with the propagation characteristics of acoustic signal in insulation oil for the purpose of improving the reliability of AE (acoustic emission) method used for condition monitoring of oil-immersed transformers. A discharge source was placed in insulation oil and AE sensors ($f_c$ :140 kHz) were attached on the oil tank to study the changes of velocity and propagation path with the depth and distance. The average velocity was 1,436 m/s and the velocity decreased with the increase of depth from the oil surface to 430 mm. The propagation paths were classified into three sections by the shortest reflection path of the detected signal. The minimum distinguishable distance in each section was 70 mm. It was also verified that PD (partial discharge) with a magnitude over than 500 pC can be detected by the AE sensors.

• Korean Chemical Engineering Research
• /
• v.48 no.4
• /
• pp.450-456
• /
• 2010

This study was conducted in order to design a piston, part of a shock absorber, and the findings after examining the features of the velocity distribution and the static pressure distribution of oil on a low-velocity piston are as follow. The compression speed of oil passing through an 0.9 mm orifice was 0.0156~0.0642 m/s, and the velocity vector of the velocity distribution and the static pressure distribution had a greater tendency to rotate when the velocity increased. In case of the velocity vector of the velocity distribution and the static pressure distribution with an 0.8mm orifice, the speed changed secondarily, the second pressure-drop was observed and as for the distribution of the streamline around the orifice, a vortex was produced around the center. As for the velocity distribution of oil passing from the compression cylinder to the compact pipe, the velocity was greater in orifice of small diameter. Also, the greater the pressure difference was between the compression cylinder and the compact cylinder, the greater the force it was upon the piston.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.3
• /
• pp.447-451
• /
• 2013

In this study, a shock absorber whose orifice area changes according to the oil pressure inside the absorber is developed. The orifice widens and narrows when the oil pressure is high and low, respectively; thus, the orifice area changes according to the oil pressure, in other words, according to the extension/compression velocity. It is well known that the damping force can be expressed as $C{\cdot}v^{\alpha}$. For fluid film damping, the force is proportional to velocity, i.e., ${\alpha}=1$, and for orifice damping, it is proportional to the square of velocity, i.e., ${\alpha}=2$. The shock absorber proposed in this paper can exhibit different relationships between the damping force and velocity because the orifice area changes according to the induced oil pressure. The motivation of this study is to develop a method for designing a shock absorber with desired values of C and ${\alpha}$ which is not just 1 or 2. Theoretical and experimental studies have been conducted to verify the damping characteristics of the shock absorber. The effect of some major design parameters on damping characteristics has been also examined to relate the design parameters to the damping characteristics.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.11a
• /
• pp.332-335
• /
• 1995

Electrification pipe modeled on the oil path of the high power transformer is designed and manufactured. Distributions of oil flow velocity are simulated as spacer form in the electrification pipe. Streaming currents are investigated as each electrification pipe. The surface oil velocity of spacer is small the streaming current.

• Electrical & Electronic Materials
• /
• v.7 no.3
• /
• pp.236-242
• /
• 1994

In this paper, the streaming electrification characteristics of insulating oil were examined when the oil is contacted with solid materials in a circulating system. The streaming current($I_s$) increases with increasing oil velocity and temperature, and electrification properties depend on species of metal materials. $I_s$ in the gauze-contained electrification apparatus increases with increasing oil temperature below the temperature of 43[>$^{\circ}C$], but decreases above 43[>$^{\circ}C$]. On the other hand, $I_s$ is positive electrificated for the pipe of Fe, Cu, while it is negative electrificated for Sus. When insulating oil flows through a car fuel filter, $I_s$ increases linearly with increasing oil temperature.