• Journal of the Society of Naval Architects of Korea
• /
• v.47 no.3
• /
• pp.438-446
• /
• 2010

The purpose of this study is to establish the proper evaluation method of member forces on the propulsion shaft using strain gages to confirm bearing offset. The strain measurements to find out the bending moments of the shaft have been performed in the yard to be compared with the results of the shaft alignment analysis. The clutch of the propulsion shaft is highly sensitive to shear forces as well as bending moments and the necessity of the measurement of shear forces on the shaft for normal operation of the clutch is recently on the rise. In this study, an evaluation method of the member forces (bending moments and shear forces) of the shaft clutch based on the shaft strain measurement is established. Through the application of this method to the eight $216,000\;m^3$ LNG carriers, the safeties of the clutch systems are evaluated and the better bearing offsets are deduced for the LNG carriers. After adjusting the bearing offsets, all the sea trials of the eight LNG carriers are successfully carried out without any troubles.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.06a
• /
• pp.224-230
• /
• 2001

A numerical analysis for the gas lubricated flexure-pivot tilting pad journal bearing has been accomplished. The film pressure are obtained by Newton-Raphson method and the dynamic coefficients are evaluated by the pad assembly method. The effects of the pivot position of the pad on the static and dynamic characteristics are presented for three pads journal bearing with LBP. The optimum pivot positions for the static performance is different from that of the dynamic performance.

• Journal of the Korean Wood Science and Technology
• /
• v.31 no.3
• /
• pp.61-69
• /
• 2003

This study investigated the effect of moisture content and loading direction on dowel bearing strength of two types of SCL. Dowel bearing tests of LVL and PSL were conducted with two different MC level, 7.5% and 19%, and two different oriention, L-direction(loading parallel to grain) and X-direction(loading perpendicular to grain). Most of specimens showed typical load-deformation curves and intersected 5% offset line. Failure modes were classified into two categories; spliting(for L-direction specimens) and peeling(for X-direction specimens). Dowel bearing strength generally decreased with increasing MC. The decreasing rate was more significant in X-directon. ESG also decreased with increasing MC, and the ratio of ESG of 7.5% versus 19% was about 1.47. Dowel bearing strength of LVL and PSL in L-direction was higher than that of X-direction. This results indicated that MC and loading orientation had a significant effect on dowel bearing strength of SCL. The average dowel bearing strength of LVL were higher than that of PSL in each loading direction. Two types of probability distribution model were chosen to quantify strength distribution, normal and 2-parameter weibull distribution. The two models showed good agreement with the data, especially in lower tail of the cumulative distribution. Normal and 2-parameter weibull distribution seemed to proper model of the dowel bearing strength for each MC levels.

• Journal of the Korean Society of Safety
• /
• v.13 no.1
• /
• pp.34-39
• /
• 1998

This paper describes a evaluation method of sound power radiated from the vibrating faces of a single stage gear box using sound radiation. The vibration caused from meshing gears is transmitted to the gear box faces through shafts and bearings. A Boundary Element Method (BEM) is developed to calculate the sound power radiated from the faces with their velocity response which is based on the Building Block Approach (BBA). Radiation efficiency as well as the sound intensity on the surface of the gear box is also calculated. Sound power of the gear box is larger in the case that bearings have offset to the wall of the gear box than that bearings are on the center of the gear box. The sound power increases with the augmentation of the offset.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.11
• /
• pp.1057-1063
• /
• 2012

A cycloid speed reducer is a type of the speed reducers. The cycloid speed reducer has a eccentric rotating motion and offset to avoid some problem of assembly, so it has a disadvantage for vibration. In this paper, a multi-body dynamic model is developed for a cycloid speed reducer and the dynamic behaviors of the reducer are investigated. The cycloid speed reducer consists of cycloidal plate gears, housing gear, input shaft, output pin and shaft, and eccentric bearings. Using a CAD program, each component of cycloid reducer is modeled based on the offset and multi-body simulations are performed using Recurdyn. As a result, the pin reaction force and the amplitude of bearing displacement are increased by the offset.

• Tribology and Lubricants
• /
• v.33 no.2
• /
• pp.37-44
• /
• 2017

A DE-side LBP tilting pad journal bearing of a 1-stage overhung heat-pump compressor in a propylene process exhibited abnormal high-temperature behavior. Its temperature had been relatively high at $78^{\circ}C$ from the beginning of operation. In 2014, after three years of operation, it increased suddenly and reached $103^{\circ}C$. Installing a varnish removal equipment and others managed to stabilize the temperature at $95^{\circ}C$. We undertook a troubleshooting approach for reviewing the comprehensive status and integrity of the temperature design of the bearing. We performed lubrication and heat-balance analysis, based on the design engineering data and documents supplied by the OEM. For the base design data of DE-side TPJB, evaluating the effects of key design variables on bearing metal temperature showed that firstly, increasing the bearing clearance and supply oil flow-rate, and next, changing the oil type, and finally, increasing the machined pad clearance and offset, are more effective in reducing the bearing metal temperature. Furthermore, a clarification meeting with the OEM revealed that an incorrect decision had been made to decrease the bearing clearance to eliminate the SSV harshness issue, while not maintaining a sufficient oil flow-rate. We conducted a detailed retrofit design analysis, wherein we increased the oil flow-rate and bearing clearance by decreasing the preload. We predicted that the bearing temperature would decrease to $63^{\circ}C$ from $75.7^{\circ}C$ even at the rerate condition. Finally, after installing and operating a retrofit replacement bearing in 2015, the bearing temperature stabilized at a low temperature of $65^{\circ}C$. Currently (January. 2017), two year later, the bearing metal temperature remains at $65^{\circ}C$. Therefore, we can conclude that the abnormal high-temperature behavior of the bearing has been resolved completely.

• Tribology and Lubricants
• /
• v.28 no.5
• /
• pp.197-202
• /
• 2012

In this study, with the purpose of fundamentally improving the unbalance response vibration of a large PRT motor-generator rotor by design, a performance improvement design analysis is carried-out by retrofitting tilting pad bearings, replacing the plain partial journal bearings that were originally applied for operation at a rated speed of 1,800 rpm. In this process, a goal of the design analysis is to obtain a design solution for maximizing the direct stiffness of the bearings while satisfying the key basic lubrication performance requirements such as the minimum lift-off speed and maximum oil-film temperature. The results show that with a careful design application of tilting pad journal bearings for operation at such a relatively low speed of 1,800 rpm, direct stiffness increment of the bearings by about two times can be effectively achieved. Prevention of pad unloading is also considered in the analysis. Moreover, the designs of elliptical and offset half journal bearings are also analyzed and reviewed.

• Geophysics and Geophysical Exploration
• /
• v.12 no.3
• /
• pp.255-262
• /
• 2009

Conventionally, vertical-seismic-profiling (VSP) survey that provides high-resolution information has mainly performed to obtain the exact depth of the gas hydrate-bearing sediment, which is one of the key factors in the development of the gas hydrate. In this study, we extracted interval velocities and created corridor stacks from the first domestic zero-offset VSP data, which were acquired with three component receivers at UBGH09 borehole in Ulleung Basin where gas hydrate exists. Then we compared the corridor stacks with a CMP stacked section from surface seismic data. First of all, we converted the signals recorded with three component receivers to true vertical and horizontal components by phase rotation, and divided the data into direct waves and reflected waves by wavefield separation processing. The trend of the interval velocity extracted from the zero-offset VSP was similar to that of the sonic log obtained at the same borehole. Because the interval velocity of the gas hydrate-bearing sediment above the BSR was high, and it decreased suddenly through the BSR, we could infer that free gas is accumulated below the BSR. The results of comparing the corridor stacks to the CMP stacked section of the surface seismic data showed that most reflection events agreed well with those in the surface CMP stacked section and that the phase-rotated VSP data corresponded better with the surface seismic data than the VSP data without phase rotation. In addition, by comparing a corridor stack produced from the transverse component with the CMP stacked section of the surface seismic data, we could identify PS mode-converted reflections in the CMP stacked section.

• Tribology and Lubricants
• /
• v.37 no.3
• /
• pp.99-105
• /
• 2021

In this study, for a high-pressure turbine (HPT) of 800 MW class supercritical thermal-power plant, considering aerodynamic cross-coupling, we performed a rotordynamic logarithmic decrement (LogDec) stability analysis with various tilting pad journal bearing (TPJB) designs, which several steam turbine OEMs (original equipment manufacturers) currently apply in their supercritical and ultra-supercritical HPTs. We considered the following TPJB designs: 6-Pad load on pad (LOP)/load between pad (LBP), 5-Pad LOP/LBP, Hybrid 3-Pad LOP (lower 3-Pad tilting and upper 1-Pad fixed), and 5-Pad LBPs with the design variables of offset and preload. We used the API Level-I method for a LogDec stability analysis. Following results are summarized only in a standpoint of LogDec stability. The Hybrid 3-Pad LOP TPJBs most excellently outperform all the other TPJBs over nearly a full range of cross-coupled stiffness. In a high range of cross-coupled stiffness, both the 6-Pad LOP and 5-Pad LOP TPJBs may be recommended as a practical conservative bearing design approach for enhancing a rotordynamic stability of the HPT. As expected, in a high range of cross-coupled stiffness, the 6-Pad LBP TPJBs exhibit a better performance than the 5-Pad LBP TPJBs. However, contrary to one's expectation, notably, the 5-Pad LOP TPJBs exhibit a slightly better performance than the 6-Pad LOP TPJBs. Furthermore, we do not recommend any TPJB design efforts of either increasing a pad offset from 0.5 or a pad preload from 0 for the HPT in a standpoint of stability.

• Geophysics and Geophysical Exploration
• /
• v.14 no.1
• /
• pp.25-41
• /
• 2011

AVO analysis was conducted on hydrocarbon-bearing structures by applying the crossplot and offset-coordinate amplitude polynomial techniques. To evaluate the applicability of the AVO analysis, it was conducted on synthetic data that were generated with an anticline model, and field data from the hydrocarbon-bearing Colony Sand bed in Canada. Analysis of synthetic data from the anticline model demonstrates that the crossplot method yields zero-offset reflection amplitude and amplitude variation with negative values for the upper interface of the hydrocarbon-bearing layer. The crossplot values are clustered in the third quadrant. The results of AVO analysis based on the coefficients of the amplitude polynomial are similar to those from the crossplots. These well correlated results of AVO analysis on field and synthetic data suggest that both methods successfully investigate the characteristics of the reflections from the upper interface of a hydrocarbon-bearing layer. Analysis based on the incident-angle equation facilitates the application of various interpretation methods. However, it requires the conversion of seismic data to an incident angle gather. By contrast, analysis using coefficients of the amplitude polynomial is cost-effective because it allows examining amplitude variation with offset without involving the conversion process. However, it warrants further investigation into versatile application. The two different techniques can be complement each other effectively as AVO-analysis tools for the detection of hydrocarbon reservoirs.