• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.5
• /
• pp.1-9
• /
• 2004

The performance analysis code has been developed for vertical take-off and landing(VTOL) UAV which can be utilized as a trade analysis tool in the pre-conceptual design phase. The UAV requires VTOL capability and high speed cruise performance. The main logic of this performance analysis code is to estimate performance parameters of each mission segment by mission fuel weight iteration. The reliability of this performance analysis code is discussed by comparing the data of existing dual flight mode VTOL UAVs such as Boeing CRW and Bell Tilt Rotor.

• 연구논문집
• /
• s.26
• /
• pp.43-50
• /
• 1996

Present paper describes on/off design performance analysis of an 74KW industrial turboshaft gasturbine engine. Procedures to match between the compressor, combustor and turbine have been incorporated into the developed program satisfying compatibility requirement of flow and work and ratational speed. The validity of the performance results from the developed program are yet to be proved through performance experiments of the resultant engine, but comparison of the present results with those from "GASCAN(Thermoflow:America) under similar mass inlet flow, pressure ratio, and speed condition show good agreement despite present results underpredict 6-10% for power and up to 3% in efficiency, respectively.

• International journal of advanced smart convergence
• /
• v.6 no.4
• /
• pp.1-8
• /
• 2017

In this work, the effects of fairly influential factors on performance of vacuum system, such as constant pressure and outgassing effect were simulated to propose the optimum design factors. Outgassing effects of selected vacuum materials on the vacuum characteristics were simulated by the $VacSim^{Multi}$ simulation tool. This investigation examined the feasibility of reliably simulating the outgassing characteristics of common vacuum chamber materials (aluminum, copper, stainless steel, nickel plated steel, Viton A). The optimum design factors for vacuum systems were suggested based on the simulation results. And, the effects of throttle valve applications on vacuum characteristics were also simulated to obtain the optimum design model of variable conductance on high vacuum system. Simulated vacuum characteristics of the proposed modelling were agreed with the observed experimental behaviour of real systems. Pressure limit valve and normally on-off control valve were schematized as the modelling of throttle valve for the constant process-pressure. Simulation results were plotted as pump-down curve of chamber and variable conductance of throttle valve. Simulated behaviors showed the applications of throttle valve sustained the process-pressure constantly, stably, and reliably.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.10a
• /
• pp.130-136
• /
• 2009

The goal of this paper is to develop a standard side mirror geometry that will perform well across multiple vehicles. One of the important performance attributes of a side mirror is the amount of wind noise generated under the flow conditions on a car. PowerFLOW can be used for Computer Aided Testing of the aeroacoustics performance of a design in addition to directing design modifications based on a detailed analysis of the flow structures responsible for the noise generation. Alternatively, a Design of Experiment (DOE) approach is useful to explore the design space without any a-priori assumptions of the effects of design parameter changes. Some general design guidelines regarding the significant mirror geometry factors will be determined which may help to reduce vehicle development time and cost in the future. The results of this research will also allow us to estimate the trade-off between cost saving and performance optimum related to using a standard mirror shape for different vehicles.

• Journal of Positioning, Navigation, and Timing
• /
• v.9 no.4
• /
• pp.293-304
• /
• 2020

In this paper, various modulation techniques, including the legacy Global Navigation Satellite System (GNSS) signal modulation techniques, are introduced and the spectral characteristics and correlation characteristics of signals with various modulation techniques are analyzed based on numerical simulation. With the development of various GNSS services, the limited frequency band has become increasingly saturated, and issues of interoperability and compatibility have emerged in the new GNSS design. Since the efficient allocation of frequency resources is closely related to spectrum design, modulation techniques are one of the important signal design parameters of new signal design. Signal modulation techniques are closely related to various figure of merits (FoMs) as well as spectrum characteristic, and in some cases there is a complicated trade-off between FoMs. Thus, the FoMs associated with modulation technology should be analyzed and the best signal candidates should be chosen carefully via the trade-off analysis for FoMs. In this paper, we define the modulation technique based on Phase Shift Keying (PSK), Binary Offset Carrier (BOC) and Continuous Phase Modulation (CPM) for the design of KPS signals, and the FoMs of signals in terms of spectrum and correlation function are evaluated. Signals with various modulation techniques are implemented through a numerical simulation, and the relevant FoMs are analyzed.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.654-656
• /
• 2002

The pole shape. turn-on angle. and turn-off angle are important design factors that largely influence Switched Reluctance Motor' s performance when designing a switched reluctance motor. These design factors must be considered simultaneously because an independent factor restricts the improvement of the switched reluctance motor' s performance. After performing the analysis using nonlinear same characteristic finite element method that contains a operating circuit, the influence upon the torque characteristics was analyzed by the pole shape and the angles. This paper presents the most suitable design value according to input conditions and various speeds. Especially.the most suitable angles were derived from the voltage equation. and an effective design range is showed from the angles.

• International Journal of Fluid Machinery and Systems
• /
• v.9 no.2
• /
• pp.143-149
• /
• 2016

In this study, a method for the multi-objective optimization of an impeller for a centrifugal compressor using fluid-structure interaction (FSI) and response surface method (RSM) was proposed. Numerical simulation was conducted using ANSYS CFX and Mechanical with various configurations of impeller geometry. Each design parameter was divided into 3 levels. A total of 15 design points were planned using Box-Behnken design, which is one of the design of experiment (DOE) techniques. Response surfaces based on the results of the DOE were used to find the optimal shape of the impeller. Two objective functions, isentropic efficiency and equivalent stress were selected. Each objective function is an important factor of aerodynamic performance and structural safety. The entire process of optimization was conducted using the ANSYS Design Xplorer (DX). The trade-off between the two objectives was analyzed in the light of Pareto-optimal solutions. Through the optimization, the structural safety and aerodynamic performance of the centrifugal compressor were increased.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.2
• /
• pp.136-143
• /
• 2004

This paper presents three algorithms of repetitive controller for compensation of the repeatable runout in hard disk drive. The basic theory of the repetitive controller and the analysis of the disturbance in hard disk drive are introduced. The tracking controller is designed in order to design the "plug-in type" repetitive controller. Design of the repetitive controller is considered as the design of the filter, determination of gain and design of additional compensation for the various types. Specially, trade-off relationship between stability and performance is important for the design. The three kinds of "plug-in type" repetitive controllers are designed, simulated and experimented. Performance and characteristic of them are compared with the analysis of the experimental results.

• The KSFM Journal of Fluid Machinery
• /
• v.13 no.5
• /
• pp.58-63
• /
• 2010

Optimal operation of turbo blowers connected in serial is analyzed by experimental measurements and numerical simulation with three-dimensional Navier-Stokes equations. The turbo blower system considered in the present study is widely used for the refuse collection system. Design optimization of the turbo blower using some design variables is also studied to enhance the performance of the blower. Throughout numerical simulation, it is found that the input energy reduction by optimal operation of the turbo blowers with the proper changes of the rotor's rotating frequency can be reduced a input energy for operating the blower system compared to the conventional on-off operation method theoretically. It is also found that the optimal design method is effective to enhance the performance of the turbo blower.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.1083-1088
• /
• 2003

This paper presents three algorithms of repetitive controller for compensation of the repeatable uncut in hard disk drive. The basic theory of the repetitive controller and the analysis of the disturbance in hard disk drive are introduced. The tracking controller is designed in order to design the "plug-in type" repetitive controller. Design of the repetitive controller is considered as the design of the filter, determination of Gain and design of additional compensation for the various types. Specially, trade-off relationship between stability and performance is important factor for the design. The thee kinds of "plug-in type" repetitive controllers are designed simulated and experimented. Performance and characteristic of them are compared by the analysis of the experimental results