• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.4
• /
• pp.447-453
• /
• 2016

The reduction technologies of exhaust gas from both the off-road engine and on-road vehicles are important. It is possible to apply various combustion technologies with engines after the application of a treatment technology to this field. In this study, main injection timing, pilot injection timing, and exhaust gas recirculation (EGR) rate were selected as the experimental parameters whose effects on the emission of exhaust gases and on the fuel consumption characteristics were to be determined. In the experiment, the emission of nitrogen oxide (NOx) and Smoke, and the Torque at the same fuel consumption level, were measured. The experimental data were analyzed using the Taguchi method with an L9 orthogonal array. Additionally, analysis of variation (ANOVA) was used to confirm the influence of each parameter. Consequently, the level of each parameter was selected based on the signal-to-noise ratio data (main injection timing, 3; pilot injection timing, 3; EGR rate, 2), and the results of the Taguchi prediction were verified experimentally (error: NOx, 10.3 %; Smoke, 6.6 %; brake-specific fuel consumption (BSFC), 0.6 %).

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.6
• /
• pp.123-134
• /
• 2013

Strengthening vehicle emission regulation is one of important policies to improve air quality in urban area. Due to the limitation of specified driving cycles for certification test to reflect real driving conditions, additional off-cycle emission regulations have been adopted in US and being developed in Europe. The driving cycles of US or Europe have been used in emission certification for Korean light-duty vehicles, but it has not been known how well the driving cycles reflect various real driving patterns in Korea. In that point of view, it is required to estimate vehicle emission based on real road driving conditions to raise the effectiveness of vehicle emission regulation in Korea. In this study, real driving emission measurements have been conducted for three Korean light-duty vehicles with PEMS. The driving routes consisted of urban, rural and motorway in Seoul and Incheon. The data have been analyzed with various averaging methods including moving averaging windows method and compared to emission limits set with emission certification modes applied to tested vehicles. The results have shown that the real driving pollutant emissions of a gasoline and a LPG vehicles have been ranged quite lower than those of emission limits on CVS-75 driving cycle. But real driving NOx of a light duty diesel vehicle has been considerably higher than emission limit of NEDC driving cycle. The higher than expected NOx emission of a diesel vehicle might be caused by different strategy to control EGR in real driving condition from NEDC driving.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.10
• /
• pp.1678-1683
• /
• 2001

The mobility of tracked vehicles is mainly influenced by the interaction between tracks and soil, so that the characteristics of their interactions are quite important fur the tracked vehicle study. In particular, the track tension is closely related to the maneuverability of tracked vehicles and the durability of tracks and suspension systems. In order to minimize the excessive load on the tracks and to prevent the peal-off of tracks from the road-wheels, the Dynamic Track Tensioning System (DTTS) which maintains the optimum track tension throughout the maneuver is required. It consists of track tension monitoring system, track tension controller and hydraulic system. In this paper, a dynamic track tensioning system is developed for tracked vehicles which are subject to various maneuvering tasks. The track tension is estimated based on the idler assembly model. Using the monitored track tension and con sidering the highly nonlinear hydraulic units, fuzzy logic controllers are designed in order to control the track tension. The track tensioning performance of the proposed DTTS is verified through the simulation of the Multi -body Dynamics tool.

• International Journal of Highway Engineering
• /
• v.15 no.5
• /
• pp.111-122
• /
• 2013

PURPOSES : The purpose of this system (Rear Lighting System) is to provide illumination for the driver to operate the commercial vehicle safely after dark in highway, to increase the conspicuity of the vehicle, and especially be suggesting the finest observable improvement method, depending on color and pattern of rear lighting system of truck for midnight highway traffic. METHODS : Rear lightning system as an improving way for forward commercial vehicles lighting the securing sight from human factors and the surrounding environment in midnight driving. For this one, basic materials were collected from the data analysis about many types of problems, and filed investigation for establishing Driving Simulator. also taking statistic test to human volunteers after finding recognizable distance of them. RESULTS : As a result, color with the highest visuality is amber followed by green-red-blue as in order for all road types. Especially almost no difference is found between red and green, also when the light is turn off, recognizable distances is wide difference compared to turn on the light. One more thing about study per pattern, upper and entire lighting have similar recognizable distances, but under lighting shows short distance with difficulty securing sight from medians. And straight section shows similar recognizable distances. By finding visuality improvement method depending on color and pattern of supplement taillight, it is expected to suggest quantitative judgement standard for introducing regulation and improvement of supplement taillight. CONCLUSIONS : Night time vehicle conspicuity to the rear is provided by rear position lamps. this study is showed that the color of light ramp is not important to be safe driving, most important is to turn on the light, recognizable distances is big different compared to turn off the rear light, so when the drivng dark in highway, have to turn on the light for reducing risk.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.5
• /
• pp.681-687
• /
• 2003

Terrain surfaces have to be modeled in very detail and wheel-surface contacting geometry must be well defined in order to obtain proper ground-reaction and friction forces fur realistic simulation of off-road vehicles. Delaunay triangulation is one of the most widely used methods in modeling 3-dimensional terrain surfaces, and the T-search is a relevant algorithm for searching resulting triangular polygons. The T-search method searches polygons in a successive order and may not allow real-time computation of off-road vehicle dynamics if the terrain is modeled with many polygons, depending on the computer performance used in the simulation. The dynamic T-search, which is proposed in this paper, combines conventional T-search and the concept of the dynmaic-window search which uses reduced searching windows or sets of triangular surface polygons at each frame by taking advantage of the information regarding dynamic charactereistics of a simulated vehicle. Numerical tests show improvement of searching speeds by about 5% for randomly distributed triangles. For continuous search following a vehicle path, which occurs in actual vehicle simulation, the searching speed becomes 4 times faster.

• Proceedings of the Korea Society for Simulation Conference
• /
• 2002.11a
• /
• pp.163-170
• /
• 2002

Terrain surfaces have to be modeled in very detail and wheel-surface contacting geometry must be well defined in order to obtain proper ground-reaction and friction forces for realistic simulation of off-road vehicles. Delaunay triangulation is one of the most widely used methods in modeling 3-dimensional terrain surfaces, and T-search is a relevant algorithm for searching resulting triangular polygons. The T-search method searches polygons in successive order and may not allow real-time computation of off-road vehicle dynamics if the terrain is modeled with many polygons, depending on the computer performance used in the simulation. In order to accelerate the searching speed of T-search, a terrain database of triangular polygons is modeled in multi-levels by adopting the LOD (Level of Detail) method used in realtime computer graphics. Simulation results show that the new LOD search is effective in shortening the required computing time. The LOD search can be even further accelerated by introducing an NN (Neural Network) algorithm, in the cases where a appropriate range of moving paths can be predicted by cultual information of the simulated terrain, such as lakes, houses, etc.. Numerical tests show that LOD-NN search almost double the speed of the original T-search.

• Journal of Biosystems Engineering
• /
• v.24 no.2
• /
• pp.89-98
• /
• 1999

In this paper, to estimate the effectiveness of the tractive performance prediction model(TPPMTV98) which was developed to predict the tractive performance of flexible tracked vehicles in previous paper, the experimental substantiation of the TPPMTV98 were conducted with the reconstructed tracked vehicle on the loam soil with the moisture content of 18.92%, and bevameter was constructed in order to measure soil properties in situ. The drawbar pulls measure were compared with predicted ones. As a result, the predicted drawbar pulls by the TPPMTV98 were well matched to the measured ones. Such results implied that the TPPMTV98 could well estimate the drawbar pulls at given soil conditions, and would be very useful as a simulation tool for designing a flexible tracked vehicle and predicting its tractive performance.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.2
• /
• pp.77-82
• /
• 2018

Track shoes improve the off-road driving ability of tanks. The strength of the track shoe body directly affects the driving ability of tanks, self-propelled artillery, and armored vehicles. In this study, the design technique for track shoe body was investigated. To select the optimal design of track shoe body, three track shoe body models were suggested and compared. Tensile strength was calculated using computer-aided engineering (CAE) analysis. Compressive tests were conducted using the original tank sprocket because sprocket compression is critical to the lifespan of the track shoe body. As a result, one track shoe body design was selected and the process of track shoe body design was described.

• Journal of Biosystems Engineering
• /
• v.25 no.5
• /
• pp.359-368
• /
• 2000

In this paper, mathematical model was developed for predicting the tractive performance of off-road wheeled vehicles operated on soft terrains. Based on the mathematical model, a computer simulation program(TPPMWV) was developed. The model takes into account main design parameters of wheeled vehicle, including radius and width of front and rear tire, weight of vehicle, wheelbase and driving type(4WD, 2WD). Soil characteristics, such as the peressure-sinkage and shearing characteristics and the response to repetitive loading and slip-sinkage effect, are also taken into consideration. The effectiveness of the developed model was verified by comparing the predicted drawbar pulls using TPPMWV with measured ones obtained by field tests for two different driving types of wheeled vehicle. As a results, the drawbar pulls predicted by the TPPMWV were well matched to the measured ones within the absolute errors of 3.916%(4WD) and 13.31%(2WD) for two different driving types, respectively.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.10a
• /
• pp.293-298
• /
• 1993

In ground vehicles, the increasing demand for safety and ride comfort which are trade-off relation, especially at high speeds, has led to the development od actively controlled suspensions. The LQG/LTR controller can be used to design a robust feedback control system that deals with disturbance rejection properties as well as insensitivity to modelling errors and sensor noise. And when the disturbance can not be measured but is limited within a certain frequency range, a bandpass feedback to eliminate the disturbance response can be used. In this paper, hybrid controller cosisted of bandpass feedback controller and LQG/LTR controller is applied to a quarter-car model moving on a randomly profiled road. The random road profile considered as colored noise is shaped from white noise by use of shaping filter. The performance of the hybrid control system is compared with that of an LQG/LTR controlled system.