• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2002년도 ICCAS
• /
• pp.106.2-106
• /
• 2002

$\textbullet$ Contents 1. Introduction $\textbullet$ Contents 2. System Configuration $\textbullet$ Contents 3. Robot Kinematics $\textbullet$ Contents 4. Shoe outsole shape display program and creating data $\textbullet$ Contents 5. Conclusions

• 한국정밀공학회지
• /
• 제13권1호
• /
• pp.131-142
• /
• 1996

Most industrial robots cannot be off-line programmed to carry out a task accurately, unless their kinematic model is suitably corrected through a calibration procedure. However, normal calibration is an expensive and time-consumming precedure due to the highly accurate measurement equipment required and due to the significant amount of data that must be collected. This paper presents a simple and economic procedure to improve the efficiency of robot calibration especially for arc welding application. To simplify the measurement process, an automotic data measurement algorithm as well as a simple measurement device are developed. Also, a calibration algorithm which can automatically identify the independent model parameters to be estimated is presented. To demonstrated the simplicity and the effectiveness of the procedure, experimental studies and computer simulations are performed and their results are discussed.

• 수산해양기술연구
• /
• 제49권2호
• /
• pp.153-160
• /
• 2013

Control allocation is an important part of a system. It implements the function that map the desired command forces from the controller into the commands of the different actuators. In this paper, the authors present an approach for solving constrained control allocation problem in vessel system by using multi-parametric quadratic programming (mp-QP) algorithm. The goal of mp-QP algorithm applied in this study is to compute a solution to minimize a quadratic performance index subject to linear equality and inequality constraints. The solution can be pre-computed off-line in the explicit form of a piecewise linear (PWL) function of the generalized forces and constrains. The efficiency of mp-QP approach is evaluated through a dynamic positioning simulation for a vessel by using four tugboats with constraints about limited pushing forces and found to work well.

• ETRI Journal
• /
• 제28권5호
• /
• pp.631-637
• /
• 2006

In this paper we study the optimization issues of ring networks employing novel parallel multi-granularity hierarchical optical add-drop multiplexers (OADMs). In particular, we attempt to minimize the number of control elements for the off-line case. We present an integer linear programming formulation to obtain the lower bound in optimization, and propose an efficient heuristic algorithm called global bandwidth resource assignment that is suitable for the design of large-scale OADM networks.

• 한국품질경영학회:학술대회논문집
• /
• 한국품질경영학회 1998년도 The 12th Asia Quality Management Symposium* Total Quality Management for Restoring Competitiveness
• /
• pp.680-695
• /
• 1998

The objective of this study is to optimize the responses of the creep feed ceramic grinding process simultaneously by an off-1ine multicriteria optimization methodology. The responses considered as objectives are material removal rate, flexural strength, normal grinding force, workpiece surface roughness and grinder power. Alumina material was ground by the creep feed grinding mode using superabrasive grinding wheels. The process variables optimized for the above objectives include grinding wheel specification, such as bond type, mesh size, and grit concentration, and grinding process parameters, such as depth of cut and feed rate. A weighting method transforms the multi-objective problem into a single-objective programming format and then, by parametric variation of weights, the set of non-dominated optimum solutions are obtained. Finally, the multi-objective optimization methodology was tested by a sensitivity analysis to check the stability of the model.

• Journal of Welding and Joining
• /
• 제14권1호
• /
• pp.30-37
• /
• 1996

조선에서 추진되어온 용접로봇의 적용은 주로 대조립 용접공정의 자동화로서, 갠트리(Gantry)에 용접토치를 장착한 로봇을 설치하여 구성하였다. 이러한 시스템에 서의 용접은 로봇을 용접부위까지 이송시킨 후 로봇의 구동으로 용접을 수행하거나, 또는 로봇과 캔트리의 동시 구동으로 용접을 수행하기도 한다. 또한 이 공정은 복잡 한 용접구조물을 OLP(Off-Line Programming)를 이용하여 교시하므로서 효과적인 자동 화 시스템의 구성이 가능할 수 있었다. 소조립 공정은 대조립공정과 비교하면 더 간단 한 부재의 용접이라 할 수 있으나 공정과 공장의 생산방법에 따라 자동화의 어려움은 따른다. 적용되는 매니프레이타는 소조립 공정의 특성에 맞게 그 형태가 설계되어야 하고 이를 운용하는 시스템은 소조립 생산방법에 맞게 통합, 개발되는 Task-Based System"이 되어야 한다. 특히 소조립 공정은 대조립 공정과 달리 여러가지 용접 판넬 을 동시에 이송시킨 후 용접함으로서 OLP의 직접 적용을 어렵게 하는 요인이 있어 이것을 해결하는 것이 생산성을 증가시키는데 적지 않은 영향을 미친다 하겠다. 이 글에서는 소조립 용접 자동화를 구성하기 위해 필요한 젓으로서 소조립 용접 공정을 소개하고, 공정의 특성에 맞도록 설계된 매니퓰레이타 시스템과, OLP, 판넬인식, 자동 교시 모들로 이루어지는 작업인식 시스템에 관해 기술한다.기술한다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2002년도 춘계학술대회 논문집
• /
• pp.135-141
• /
• 2002

Recently, in the metro railways, researches on the skip-stop operation and development of the double deck train-set are active, which is to improve the service quality through reducing the passenger travel time and suppling seating service. Constructing new line or reforming the existent line needs huge amount of budget. Therefore, previous to start these large scale projects, scrutiny on benefit improvement, cost reduction and those optimal trade-off is indispensable. In this paper, a quantitative analysis to determine the optimal train service patterns and train-sets necessary is proposed, under the skip-stop operation condition in the metro railways. The analysis models are formulated in mathematical programming model, and tested validity using the LINGO 7.0.

• 한국산학기술학회논문지
• /
• 제17권12호
• /
• pp.446-452
• /
• 2016

최근 해양, 석유화학 플랜트 등에서는 내마모, 내식성, 내열성이 요구되는 초내열 합금이 기본적인 구조재료로 많이 사용되고 있다. 하지만 고가의 초내열 합금 소재로 밸브를 제작할 때 원가 상승과 가격 경쟁력 저하의 원인이 되고 있다. 이에 유체에 흐르는 특정부위만 육성 용접하는 기술이 효과적인 방법으로 사용되고 있다. 하지만 기존의 볼 육성용접의 경우 사람이 직접 수동으로 작업을 진행하기 때문에 많은 시간이 소요되고 정확한 용접하기 어렵다. 이러한 문제를 해결하기 위해 볼 밸브용 볼 육성용접을 균일하게 할 수 있는 로봇자동화 시스템을 개발하였다. 이 시스템은 용접토치를 장착한 용접용 로봇 6축, 포지셔너 회전을 위한 부가 2축, 제어장치 및 로봇경로는 오프라인 프로그램으로 구성되어 있다. CAD 도면 데이터를 오프라인 프로그램에 입력하여 로봇 교시점과 로봇 구동 소스를 얻을 수 있도록 하였고, 볼 육성용접 궤적은 Matlab을 통해 구현하였다. OLP 시스템을 통해 용접층 두께가 균일하게 얻으므로 용가재의 소모량을 약 20% 절약할 수 있었고, 모재와 용접봉 사이의 아크길이를 일정하게 유지하여 육성용접 불량율을 약 50% 정도 감소시켜 품질을 확보하였다. OLP를 활용한 육성용접 자동화 시스템을 통해 작업소요시간이 88시간에서 41시간으로 단축되어 생산성이 2.58배 향상 되었다.

• 한국자동차공학회논문집
• /
• 제11권6호
• /
• pp.118-126
• /
• 2003

Digital Manufacturing is a technology facilitating effective developments and agile productions of the product via digital computer models representing physical and logical schema and the behavior of the real manufacturing systems including manufacturing resources, environments and products. For the successful application of this technology, a digital factory as a well-designed and an integrated environment is essential. In this paper, we constructed the sophisticated digital factory of a Korean automotive company's body shop, and conducted precise simulations of unit cell, lines and the whole factory for the collision check, the production flow analysis and the off-line programming. We expect that this digital factory of the body shop helps us achieve great savings in time and cost for many manufacturing preparation activities of the new car development.

• 제어로봇시스템학회논문지
• /
• 제12권3호
• /
• pp.248-254
• /
• 2006

It is necessary to improve the exactness and adaptation of the working environment for the intelligent robot system. The vision sensor have been studied for a long time at this points. However, it has many processes and difficulties for the real usages. This paper proposes a visual servoing in the virtual environment to support OLP(Off-Line-Programming) path compensation and supplement the problem of complexity of the old kinematical calibration. Initial robot path could be compensated by pixel differences between real and virtual image. This method removes the varies calibrations and 3D reconstruction process in real working space. To show the validity of the proposed approach, virtual space servoing with stereo camera is carried out with WTK and openGL library for a KUKA-6R manipulator and updated real robot path.