• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.188-192
• /
• 2003

A multilayer two-stage LC bandpass filter using low-temperature cofired-ceramic (LTCC) is proposed in this paper. The proposed bandpass filter is composed of two ceramic substrates with different dielectric constant instead of single ceramic material from top to bottom layer. The bandpass filter size is $2.0 mm{\times}1.2 mm{\times}0.8 mm$. Positioning of attenuation polefrequency, importance parameter for a performance of filter, is discussed using even-odd mode analysis by tuned capacitance of coupling capacitor and those results is implemented to LTCC filter circuit. Measured filter performances show that the insertion losses are -4.5dB, -4.1dB at 2.45GHz, 2.75GHz and the return losses are -8.5dB, 8.7dB.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.401-405
• /
• 2003

Sound quality is becoming a major concern in optical disc drives (ODD). In order to improve the sound quality of slim type ODDs, we changed lead screw pitch and firmware algorithm in the seek mode. To evaluate the sound quality, the PCM (Paired Comparison Method) was adopted and the result was compared with the time-averaged loudness spectrum. Sound signals were also recorded and modified by increasing or decreasing selected frequency bands to verify their sensitivities to the sound quality. As a result of jury test, preferred frequency bands are associated with the time-averaged loudness spectrum.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.11
• /
• pp.577-582
• /
• 2004

In this paper, lumped equivalent circuits for a conventional parallel directional coupler are proposed. This equivalent circuits only have self inductance and self capacitance, so we can design exact lumped equivalent circuit. The equivalent circuit and design formula for the presented lumped element coupler is derived based on the even- and odd-mode properties of parallel-coupled line. By using the derived design formula, we have designed the 3dB and 4.7dB MMIC couplers at the center frequency of 3.4GHz and 5.6GHz respectively. Measurements for the designed MMIC directional couplers show at 4dB and 5.2dB-coupling value at the center frequency of 3.4GHz and 5.6GHz. Excellent agreements between simulation results and measurement results on the designed directional couplers show the validity of this paper

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.2
• /
• pp.139-143
• /
• 1988

A new measurement method of coupled transmission line characteristics is described. This method presents precision values of even-and odd-mode impedances as well as effective dielectric constants of symmetric parallel coupled microstrip lines from the scalar quantities obtained by transmission coefficients at two different resonance frequencies. Especially these values include dispersion effects in the measured frequency band. The measured impedances and effective dielectric constants of actually fabricated coupled lines on the Teflon substrates with low dielectric constants are good agreement with predicted values. And the experimental pass band characteristics of single section resonator by using previously designed coupled lines agree well with theoretical values.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.6
• /
• pp.26-33
• /
• 1994

Much time and labor has been conventionally paid for fine adjustment of circuit elements by experience to improve the characteristics of Tap-off for CATV systems. To solve the problem, in this paper, the relations between the even- and odd-mode impedance. Z$_{oe}$ and Z$_{oo}$ of symmetrical 4-port coupled-line directional coupler and power dividing characteristics of Tap-off for CATV system have been derived. After the coupling, the reflectivity and the isolation are represented by Z$_{oe}$ and Z$_{oo}$ only, the fine adjustment of all S-parameters can be performed by controling the elements of Z$_{oe}$ and Z$_{oo}$ only. Furthermore, the validity of the new fine adjustment method proposed here has been confirmed by experiments.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.9
• /
• pp.1968-1974
• /
• 1997

In this paper, the spectral domain approach is employed to investigate the characteristics of symmetrical and asymmetrical broadside-coupleed coplanar waveguides(BSC-CPW). These structures have large even(c)-odd(.pi.) mode-velocity ratio, suitable for wide-band and tight-coupling microwave circuit design. Efficient design parameters can be obtained from the effective dielectric constants and characteristic impedances calculated by varying the strip widths and slot widths in the BSC-CPW structure.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.34.2-34
• /
• 2001

There are many control methods guaranteeing the robustness of systems. Among them, H$\infty$ control, sliding mode control and disturbance observer have been used widely. Especially, disturbance observer(DOB) is one of the most popular methods because it is easy to apply and the cost to pay is low due to its simplicity. Conventional DOB utilizes output signal as a feedback signal. But in Optical Disk Drive(ODD) systems, the Position Error Signal(PES) is the only available one. So conventional DOB is not applicable. If we use error signal in stead of output signal, another form of DOB is made. We call it as Error based Disturbance Observer(EDOB). We show in this paper the difference between two systems, namely conventional DOB system and the EDOB system, and also show the effectiveness of EDOB through experiment.

• Journal of Electrical Engineering and information Science
• /
• v.1 no.2
• /
• pp.96-100
• /
• 1996

This paper describes a concrete method for computing characteristic impedances and effective dielectric constants of the microstrip coupled lines without and with a dielectric overlay. The frequency-independent spectral domain method is used for the analysis of these lines. This method is a powerful, accurate, and numerically efficient approach for planar transmission line structure. For designing the optimal directional coupler, the velocities of even and odd mode must be equal but velocities of these two modes are different in the conventional coupled line which is inhomogeneous. The results show that these two velocities can be almost same according to variations of structural and material parameters in terms of the overlay(superstrate).

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.10 no.6
• /
• pp.558-569
• /
• 2017

In this paper, a 256Kb EEPROM IP aimed at battery applications using a single supply of 1.5V which is embedded into an MCU is designed. In the conventional cross-coupled VPP (boosted voltage) charge pump using a body-potential biasing circuit, cross-coupled PMOS devices of 5V in it can be broken by the junction or gate oxide breakdown due to a high voltage of 8.53V applied to them in exiting the program or erase mode. Since each pumping node is precharged to the input voltage of the pumping stage at the same time that the output node is precharged to VDD in the cross-coupled charge pump, a high voltage of above 5.5V is prevented from being applied to them and thus the breakdown does not occur. Also, all erase, even program, odd program, and all program modes are supported to reduce the times of erasing and programming 256 kilo bits of cells. Furthermore, disturbance test time is also reduced since disturbance is applied to all the 256 kilo bits of EEPROM cells at once in the cell disturb test modes to reduce the cell disturbance testing time. Lastly, a CG driver with a short disable time to meet the cycle time of 40ns in the erase-verify-read mode is newly proposed.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.2028-2030
• /
• 2004

In this paper, a lumped equivalent circuit for a conventional parallel directional coupler is proposed. The equivalent circuit and design formula for the presented lumped element coupler is derived based on the even- and odd-mode properties of a parallel-coupled line. By using the derived design formula, we have designed the 3dB and 4.7dB lumped element directional couplers at the center frequency of 3.4GHz and 5.6GHz. A chip type directional coupler has been designed to fabricate with MMIC(Monolitic Microwave integrated circuit) process. Excellent agreements between simulations and measurements on the designed directional couplers show the validity of this paper.