• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 춘계학술대회 논문집
• /
• pp.902-906
• /
• 2000

In end milling process the undeformed chip thickness and the cutting force components vary periodically with phase change of the tool. In this study, up end milling process is transformed to the equivalent oblique cutting. The varying undeformed chip thickness and the cutting force components in end milling process are replaced with the equivalent average ones. Then it can be possible to analyze the chip-tool friction and shear process in the shear plane of the end milling process by the equivalent oblique cutting model. According to this analysis, when cutting SM45C steel. 82% of the total energy is consumed in the shear process and the balance is consumed in the friction process.

• Journal of Advanced Marine Engineering and Technology
• /
• 제22권2호
• /
• pp.200-209
• /
• 1998

Experiments have been conducted to determine heat transfer characteristics for a two-dimen-sional turbulent wall attaching offset jet at different oblique angles to a flat surface. The local Nusselt number distributions were measured using liquid crystal as a temperature sensor. Wall static pressure coefficient profiles were measured at the Reynolds number Re 53200(based on the nozzle width, D) the offset ratio H/D from 2.5 to 10 and the oblique angle a from $0^{\circ}$, to $40^{\circ}$ It is observed that the maximum Nusselt number point occurs slightly upstream of time-averaged reattachment point for all oblique angles. The correlations between the maximum Nusselt number and Reynolds number offset ration and oblique angle are presented.

• 설비공학논문집
• /
• 제9권4호
• /
• pp.427-434
• /
• 1997

Heat transfer characteristics of a two-dimensional oblique impinging jet were experimentally investigated. The local heat transfer coefficients were measured by a thermochromic liquid crystal. The jet Reynolds number studied was varied from 10000 to 35000, the nozzle-to-plate distance(H/B) from 2 to 16, and the oblique angle($\alpha$) from $60^{\circ}$ to $90^{\circ}$. It was observed that the local Nusselt numbers in the minor flow region were larger than those in the major flow region at the same distance along the plate due to the higher levels in the turbulent intensity caused by more active mixing of the jet flow.

• 한국항공운항학회:학술대회논문집
• /
• 한국항공운항학회 2004년도 추계학술발표대회 논문집
• /
• pp.240-246
• /
• 2004

For the prediction on the onset of oblique shock wave-induced vortex breakdown, computational studies on the Oblique Shock wave/Vortex Interaction (OSVI) are conducted and compared with both experimental results and analytic model. A Shock-stable numerical scheme, the Roe scheme with Mach number-based function (RoeM), and a two-equation eddy viscosity-transport approach are used for three-dimensional turbulent flow computations. The computational configuration is identical to available experiment, and we attempt to ascertain the effect of parameters such as a vertex strength, streamwise velocity deficit, and shock strength at a freestream Mach number of 2.49. Numerical simulations using the ${\kappa}-{\omega}SST$ turbulence model and suitably modeled vortex profiles are able to accurately reproduce many fine features through a direct comparison with experimental observations. The present computational approach to determine the criterion on the onset of oblique shock wave-induced vortex breakdown is found to be in good agreement with both the experimental result and the analytic prediction.

• 한국군사과학기술학회지
• /
• 제5권2호
• /
• pp.228-238
• /
• 2002

Using the dynamic explicit program NET3D, oblique impact between long rod penetrator and metallic plate was analyzed. Compared with an experiment and AUTODYN-3D analysis result, the accuracy of NET3D program was examined. It was proved that NET3D program could analyze comparatively exactly oblique impact phenomenon between long rod penetrator and metallic plate. The final deformed configuration of penetrator predicted by NET3D program was more close to experimental result than commercial program AUTODYN-3D. But, in order to increase the reliability of NET3D program in the simulation of tensile fracture phenomenon, the additional research is required.

• 한국전기전자재료학회논문지
• /
• 제12권1호
• /
• pp.75-80
• /
• 1999

In this study, we have investigated the relationship between the generation of pretilt angle and the polarization component in cells with UV light irradiation on polyimide (PI) surface. It was found that the generated pretilt angle is about $1.4^{\circ}$ with S-polarized UV light irradiation of $75^{\circ}$ on PI surface; it may be attributed to the asymmetry triangular of polymer surface with oblique S-polarized UV light irradiation on PI surface. Also, we measured that the generated pretilt angle is about $2.0^{\circ}$ with oblique P polarized UV light irradiation of $75^{\circ}$ on PI surface. Consequently, we suggest that the generated pretilt angle of the NLC is attributed to the interaction between the LC molecules and the polymer surface with oblique polarized UV light irradiation on PI surface.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제11권1호
• /
• pp.119-130
• /
• 2019

This paper establishes an iterative calculation model for the hydrodynamic performance of propeller in oblique flow based on low order potential based surface panel method. The hydrodynamic performance of propeller is calculated through panel method which is also used to calculate the induced velocity. The slipstream of propeller is adjusted according to the inflow velocity and the induced velocity. The oblique flow is defined by the axial inflow velocity and the incident angle. The calculation results of an instance show that the thrust and torque of propeller decrease with the increase of axial inflow velocity but increase with the incident angle. The unsteadiness of loads on the propeller blade surface gets more intensified with the increases of axial inflow velocity and incident angle. However, comparing with the effect of axial inflow velocity on the unsteadiness of the hydrodynamic performance of propeller, the effect of the incident angle is more remarkable.

• Journal of Veterinary Science
• /
• 제21권4호
• /
• pp.62.1-62.7
• /
• 2020

A 5-month old Shih Tzu was diagnosed with congenital elbow luxation and uniapical complex angular deformity of the radius. Single radial oblique and dynamic ulnar osteotomies were performed, using patient-specific 3D-printed osteotomy guide. External skeletal fixation was maintained for three weeks to prevent re-luxation of elbow joint. Three months after the surgery, objective gait analysis indicated markedly improved limb function. In addition, radiograph showed improved congruity of elbow joint and appropriate bone healing. In dogs with congenital radial head luxation and concurrent complex angular deformity, a single oblique osteotomy might be a viable option to preserve bone length and correct the luxation of elbow joint.

• 한국정밀공학회지
• /
• 제11권2호
• /
• pp.95-103
• /
• 1994

The purpose of this paper is to provide the experimenters who use the oblique incidence ultrasonic method for anisotropic elastic constants measurement eith some useful relations. In particular, the equivalence of the times of flight by the energy ad phase velocities, which is key to the oblique incidence method, is proved explicitly. This equivalence greatly simplifies the analysis of immersion measurement results. In oredr to correctly measure the transit time of an immersed sample using the oblique incidence, the receiving transducer should be shifted laterally, and an expression in given for this shift. A method for determining all nine elastic constants of an orthotropic material is briefly described and the measurement results are listed for SiC particulate reinforced A1 matrix composites.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2005년도 학술발표회(2)
• /
• pp.902-903
• /
• 2005