• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.55 no.4
• /
• pp.195-197
• /
• 2006

When we measure electrical impedance of a small object, such as an electronic component, external interference or jamming signal can be rejected by shielding the object. However, when we measure impedance of a large object, such as a human body, shielding is not easy and severe error due to the external interference could be introduced. In this paper, spread spectrum technique applicable to bioimpedance measurements for rejecting external interference without shielding is introduced. The improvement in signal-to-jamming ratio by the spread spectrum technique was experimentally confirmed.

• Proceedings of the KSR Conference
• /
• 2003.10c
• /
• pp.587-593
• /
• 2003

There has been much interest in the Bluetooth technology since it could enable users to connect to a wide range of computing and telecommunication devices without the need to carry or connect cables. It delivers opportunities for rapid, ad-hoc connections, and in the future, could possibly enable automatic, unconscious, connections between devices. In this paper, we discussed a scatternet formation protocol for Bluetooth-based ad hoc networks and proposed the identification system of an object using Bluetooth Scatternets. Over the past few years, several studies have been made on the identification of an object by several RF(Radio Frequency) systems. But there are still some problems, the interference of signals as an example, for the identification of an object. The critical question is how to identify an object precisely without the interference of signals. This paper is an investigation of the Scatternet formation protocol for Bluetooth-based ad hoc networks and the identification system of an object using Bluetooth Scatternets composed of multiple Piconets.

• Korean Journal of Oriental Medicine
• /
• v.1 no.1
• /
• pp.273-287
• /
• 1995

Moire topography, a simple technique for three-dimensional quantitation, was used to provide interference fringe photographs of the human back with sufficient accuracy to be used for detecting patient with asymmetry due to scoliosis, the disease of cervix and lumbar, muscle dysfunction. Contour lines are a suitable and widely accepted method of describing a three-dimensional surface. In the moire technique, contour lines of an object are produced as interference fringes while the object is illuminated by a spotlight through a special grating. The fringe pattern is produced by the interference of the grating and its shadow on the object. A photograph of a moire pattern on the human back will permit an assessment of the overall body shape and the symmetry of the back. This study uses shadow moire topography. Moire topography provides a non-invasive technique for quantifying the shape of the human body. In the use of moire topography for the Oriental Medicine Diagnosis, the strength of moire lies in the ablility to detect change due to deformity of human body.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.271-274
• /
• 2002

The 3-D measurement using interference pattern projection is very attractive because of its high measuring speed and high sensitivity. When a sinusoidal amplitude grating was projected on an object, the surface-height distribution of the object is translated into a phase distribution of the deformed grating image. The patters was generated by a interferometer, and a PZT was used to shift the fringes on the target surface. The phase-acquisition algorithms are so sufficiently simple that high-resolution phase maps using a CCD camera can be generated in a short time. A working system requires a interferometer, a PZT, and a detector array interfaced to a microcomputer. Results of measurements on the diffused test objects are described.

• International Journal of Aeronautical and Space Sciences
• /
• v.17 no.2
• /
• pp.253-259
• /
• 2016

The typical method for performing an absolute radiometric calibration of a Synthetic Aperture Radar (SAR) System is to analyze its response, without interference, to a target with a known Radar Cross Section (RCS). To minimize interference, an error-free calibration site for a Corner Reflector (CR) is required on a wide and flat plain or on an area without disturbance sources (such as ground objects). However, in reality, due to expense and lack of availability for long periods, it is difficult to identify such a site. An alternative solution is the use of a Triangular Trihedral Corner Reflector (TTCR) site, with a surrounding protection wall consisting of berms and a hollow. It is possible in this scenario, to create the minimum criteria for an effectively error-free site involving a conventional object-tip reflection applied to all beams. Sidelobe interference by the berm is considered to be the major disturbance factor. Total interference, including an object-tip reflection and a sidelobe interference, is analyzed experimentally with SAR images. The results provide a new guideline for the minimum criteria of TTCR site design that require, at least, the removal of all ground objects within the fifth sidelobe.

• Journal of IKEEE
• /
• v.25 no.4
• /
• pp.584-590
• /
• 2021

This paper proposes a removal method of signal interference between ultrasound sensors where ghost signals due to interference are excluded and correct signal is recognized in distance mensurement using ultrasound sensors. The proposed method detects and excludes ghost signals when previous measured distance is compared to current measured distance and the distance difference exceeds a threshold. The threshold is fixed in conventional methods, so ghost signals cannot be correctly excluded when ultrasound sensor or target object move rapidly. On the contrary, to improve accuracy, the threshold is not fixed in the proposed method, and the threshold is adpatively determined based on the relative velocity when ultrasound sensor or target object move. Experiments of distance measurement with ultrasound signal interference are carried out where multiple ultrasound sensors of same type are exploited with maximum interference, and the results show that the proposed method efficiently exclude ghost signals.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.11 no.4
• /
• pp.1841-1865
• /
• 2017

This paper proposes a new interference mitigation scheme for device-to-device (D2D) communications underlaying a cellular network. The object of the proposed scheme is to determine the number of data streams, a precoding matrix, and a decoding matrix of D2D networks so as to maximize the system capacity given the number of data streams of a cellular network while satisfying the constraint of the inter-system interference from D2D networks to the cellular network. Unlike existing interference mitigation schemes based on the interference alignment technique, the proposed scheme operates properly regardless of the number of data streams of a cellular network and moreover it does not require changing the precoding and decoding matrices of a cellular network. The simulation results demonstrate that the proposed scheme significantly increases the system capacity by mitigating the intra- and inter-system interference.

• Proceedings of the KIEE Conference
• /
• 2005.10b
• /
• pp.75-77
• /
• 2005

When measuring impedance of electronic component and so on, even the small size can reject the interference to shielding object. But, the interference through human body is grown when measuring bioimpedance without establishing shield specially. Consequently, when measuring bioimpedance in this paper, it proposed impedance measurement method to take advantage of spread spectrum technology, so that can reject the interference without establishing shield specially. Spread spectrum impedance measurement method to propose in this paper can reject the interference signal that occurring from medical instruments in the human body, the interference signal that is flowed in from surrounding environment when measuring impedance. It improved SJR(signal to jamming ratio) about 22dB than conventional method that actually realize and experiment spread spectrum impedance measurement method.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.7
• /
• pp.105-113
• /
• 2003

This paper describes the development of a 6-axis robot's finger force/moment sensor, which measures forces Fx, Fy, Fz, and moments Mx, My, Mz simultaneously, for stably grasping an unknown object. In order to safely grasp an unknown object using the robot's gripper, it should measure the force in the gripping direction and the force in the gravity direction, and perform the force control using the measured forces. Thus, the robot's gripper should be composed of 6-axis robot's finger force/moment sensor that can measure forces Fx, Fy, Fz, and moments Mx, My, Mz simultaneously. In this paper, the 6-axis robot's finger force/moment sensor for measuring forces Fx, Fy, Fz, and moments Mx, My, Mz simultaneously was newly modeled using several parallel-plate beams, designed, and fabricated. The characteristic test of made sensor was performed. and the result shows that interference errors of the developed sensor are less than 3%. Also, Robot's gripper with the 6-axis robot's finger force/moment sensor for the characteristic test of force control was manufactured, and the characteristic test for grasping an unknown object was performed using it. The fabricated gripper could grasp an unknown object stably. Thus, the developed 6-axis robot's finger force/moment sensor may be used for robot's gripper.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.29 no.3
• /
• pp.111-118
• /
• 2006

This paper presents design and development of a simulator evaluates the performance of a hierarchical cellular system. The proposed hierarchical cellular simulator, consisting of macro, micro, and pico cells, applies the wrap-around technique to reduce simulation time. The simulator is implemented as object oriented class models by using the C++ language in a PC environment. The resulting application can evaluate the interference, SIR(Signal to Interference Ratio), and capacity of a hierarchical cellular system in various configurations. Moreover, it can be used in other applications such as power control, call admission control, hand over scheme.