• Journal of Information Display
• /
• v.12 no.4
• /
• pp.213-217
• /
• 2011

Printing technologies were applied to fabricate a flexible organic thin-film transistor (OTFT) backplane for electrophoretic displays (EPDs). Various printing processes were adopted to maximize the figures of each layer of OTFT: screen printing combined with reverse offset printing for the gate electrodes and scan bus lines with Ag ink, inkjet for the source/drain electrodes with glycerol-doped Poly (3,4-ethylenedioxythiophene): Poly (styrenesulfonate) (PEDOT:PSS), inkjet for the semiconductor layer with Triisopropylsilylethynyl (TIPS)-pentacene, and screen printing for the pixel electrodes with Ag paste. A mobility of $0.44cm^2/V$ s was obtained, with an average standard deviation of 20%, from the 36 OTFTs taken from different backplane locations, which indicates high uniformity. An EPD laminated on an OTFT backplane with $190{\times}152$ pixels on an 8-in panel was successfully operated by displaying some patterns.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.648-650
• /
• 2008

We used micro-contact printing for source and drain electrodes of OTFTs. The proper solvent of Ag paste and baking temperature were extracted for PVP gate dielectric and pentacene semiconductor. The mobility was 0.025 cm2/V.sec and on/off ratio was $2{\times}10^5$.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1361-1363
• /
• 2005

In this paper, we report on the performance stability of solution processible OTFT devices with Au/Ti and ITO source-drain (S/D) electrodes. It appears that the contact resistance of the S/D electrode strongly affects the stability of OTFT devices. Interestingly, the devices with the Au/Ti electrode showed lower mobility than those with the ITO (S/D) devices. The field effect mobilities of the devices with the Au/Ti and ITO electrodes were 0.06, and $0.44cm^2/Vs$, respectively. However, the mobility of the device with the Au/Ti electrode was increased up to $0.26cm^2/Vs$ after 2 weeks, while the mobility of the device with ITO electrode was slightly decreased down to $0.41cm^2/Vs$. The experimental data show us that ITO could be used as the S/D electrode for low-cost OTFT devices.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.155-158
• /
• 2007

Printed organic thin-film transistor(OTFT) to use as a switching device for an organic light emitting diode(OLED) were fabricated in the microcontact printing and direct printing processes at room temperature. The gate electrodes($5{\mu}m$, $10{\mu}m$, and $20{\mu}m$) of OTFT was fabricated using microcontact printing process, and source/drain electrodes ($W/L=500{\mu}m/5{\mu}m$, $500{\mu}m/10{\mu}m$, and $500{\mu}m/20{\mu}m$) was fabricated using direct printing process with hard poly(dimethylsiloxane)(h-PDMS) stamp. Printed OTFT with dielectric layer was formed using special coating system and organic semiconductor layer was ink-jet printing process. Microcontact printing and direct printing processes using h-PDMS stamp made it possible to fabricate printed OTFT with channel lengths down to $5{\mu}m$, and reduced the process by 20 steps compared with photolithography. As results of measuring he transfer characteristics and output characteristics of OTFT fabricated with the printing process, the field effect characteristic was verified.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08b
• /
• pp.1789-1791
• /
• 2007

We fabricated OTFT-OLED display panel by using Ag-paste for source and drains electrode of OTFTs. The OTFTs were fabricated by solution processes such as spin-coating for PVP gate dielectric and screen printing for S/D electrodes with Ag-paste, except pentacene active layer which was deposited by evaporation. The mobility was 0.024 cm2/V.sec , off state current ${\sim}10-11A$, threshold voltage 7.6 V and on/off current ratio ${\sim}105$. The panel consisted of 16 x 16 pixels and each pixel consisted of 2 OTFTs, 1 Capacitor and 1 OLED. The pixels successfully worked in terms of current magnitude supplied to OLED and the control ability of driving and switching OTFTs.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.3
• /
• pp.7-11
• /
• 2011

In this paper, we proposed a simple and high-yield printing process for source and drain electrodes of organic thin film transistor (OTFT). The surface energy of PVP (poly 4-vinylphenol) gate dielectric was decreased from 56 $mJ/m^2$ to 45 $mJ/m^2$ by adding fluoride of 3000ppm into it. Meanwhile the surface energy of source and drain (S/D) electrodes area on the PVP was increased to 87 $mJ/m^2$ by treating the areas, which was patterned by photolithography, with oxygen plasma, maximizing the surface energy difference from the other areas. A conductive polymer, G-PEDOT:PSS, was deposited on the S/D electrode areas by brushing painting process. With such a simple process we could obtain a high yield of above 90 % in $16{\times}16$ arrays of OTFTs. The performance of OTFTs with the fluoride-added PVP was similar to that of OTFTs with the ordinary PVP without fluoride, generating the mobility of 0.1 $cm^2/V.sec$, which was sufficient enough to drive electrophoretic display (EPD) sheet. The EPD panel employing the OTFT-backpane successfully demonstrated to display some patterns on it.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1277-1280
• /
• 2005

A high-aspect-ratio and high-resolution stainless steel shadow mask for organic thin-film transistors (OTFTs) circuit has been fabricated by a new method which combines photochemical machining, micro-electrical discharge machining (micro-EDM), and electrochemical etching (ECE). First, connection lines and source-drain holes are roughly machined by photochemical etching, and then the part of source and drain holes is finished by the combination of micro-EDM and ECE processes. Using this method a $100\;\mu{m}$ thick stainless steel (AISI 304) shadow mask for inverter can be fabricated with the channel length of $30\;\mu{m}\;and\;10\;\mu{m}\;respectively.\;The\;width\;of\;connection line\;is\;150\;\mu{m}$. The aspect ratio of the wall is about 5 and 15, respectively. Metal lines and source-drain electrodes of OTFTs were successfully deposited through the fabricated shadow mask.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.04b
• /
• pp.45-48
• /
• 2002

Poly(3-hexylthiophene) or P3HT based organic thin film transistor (OTFT) array was fabricated on flexible poly carbonate substrates and the electrical characteristics were investigated. As the gate dielectric, a dual layer structure of polyimide-$SiO_2$ was used to improve the roughness of $SiO_2$ surface and further enhancing the device performance and also source-drain electrodes were $O_2$ plasma treated for improvement of the electrical properties, such as drain current and field effect mobility. For the active layer, polymer semiconductor, P3HT layer was printed by contact-printing and spin-coating method. The electrical properties of OTFT devices printed by both methods were evaluated for the comparison. Based on the experiments, P3HT-based OTFT array with field effect mobility of 0.02~0.025 $cm^{2}/V{\cdot}s$ and current modulation (or $I_{on}/I_{off}$ ratio) of $10^{3}\sim10^{4}$ was fabricated.

• Polymer(Korea)
• /
• v.33 no.5
• /
• pp.397-406
• /
• 2009

We have fabricated source-drain electrodes for OTFTs using a screen-printing technique with carbon-black pastes as conductive paste. And effects of dispersants contents (SOP 10-40%) on the dispersity of carbon-black pastes and characteristics of screen-printed source-drain electrodes for OTFTs using two types of dispersants (DB-2150, DB-9077) were investigated. As contents of both dispersants were increased the dispersity of carbon-black mill-bases was improved, whereas the carbon-black pastes exhibited different dispersion characteristics. For the case of DB-2150, the dispersity of the pastes was improved with increasing dispersant content and the storage modulus G' in their rheology characteristics were reduced. But, for the DB-9077, the storage modulus G' of pastes were increased with dispersant content due to the flocculated network structure formed by interactions among carbon-black powders and dispersants. But, since this flocculated network structure of the pastes using DB-9077 resulted in the conduction path of carbon-black structures, the conductivities of screen-printed electrodes and mobilities of the OTFTs with them were better than those using pastes with DB-2150.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.506-508
• /
• 2005

In general, organic TFTs are comprised of four components: gate electrode, gate dielectric, organic active semiconductor layer, and source and drain contacts. The TFT current, in turn, is typically determined by channel length and width, carrier field effect mobility, gate dielectric thickness and permittivity, contact resistance, and biasing conditions. More recently, a number of techniques and processes have been introduced to the fabrication of OTFT circuits and displays that aim specifically at reduced fabrication cost. These include microcontact printing for the patterning of metals and dielectrics, the use of photochemically patterned insulating and conducting films, and inkjet printing for the selective deposition of contacts and interconnect pattern. In the fabrication of organic TFTs, microcontact printing has been used to pattern gate electrodes, gate dielectrics, and source and drain contacts with sufficient yield to allow the fabrication of transistors. We were fabricated a pentacene OTFTs on flexible PEN film. Au/Cr was used for the gate electrode, parylene-c was deposited as the gate dielectric, and Au/Cr was chosen for the source and drain contacts; were all deposited by ion-beam sputtering and patterned by microcontact printing and lift-off process. Prior to the deposition of the organic active layer, the gate dielectric surface was treated with octadecyltrichlorosilane(OTS) from the vapor phase. To complete the device, pentacene was deposited by thermal evaporation and patterned using a parylene-c layer. The device was shown that the carrier field effect mobility, the threshold voltage, the subthreshold slope, and the on/off current ratio were improved.