• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1025-1028
• /
• 2005

Microcrystalline Si (${\mu}c-Si$) TFTs were fabricated using a conventional bottom gate amorphous Si (a-Si) process. A unique ${\mu}c-Si$ deposition technique and TFT architecture was proposed to enhance the reliability of the TFTs. This three-mask TFT fabrication process is comparable with existing a-Si TFT procesess. In order to suppress nucleation at the bottom interface of Si, before deposition of the ${\mu}c-Si$ an $N_2$ plasma passivation was conducted. A typical transfer characteristic of the TFTs shows a low off-current with a value of less than 1 pA and a sub threshold slop of 0.7 V/dec. The DC stress was applied to verify the use of ${\mu}c-Si$ TFTs for AMOLED displays. After 10,000 s of application of the stress, the off-current was even lowered and sub-threshold slope variation was less than 5%. For AMOLED displays, OLED pixel simulation was performed. A pixel current of 13 ${\mu}A$ was achieved with $V_{data}$ of 10 V. After the simulation, a linear equation for the pixel current was suggested.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1480-1483
• /
• 2005

Transparent thin composite films (TCFs) were deposited on OLED devices by means of RF sputtering method and their passivation-properties were evaluated by comparing to the e-beam evaporating method. This composite film formed by mixed ratio of MgO (3wt %): $SiO_2$ (1wt %) was developed from pallet as a source of e-beam evaporator to 6-inch size target for sputtering in order to apply for large-sized organic display devices. Water Vapor Transmission Rates (WVTR) of the deposited films were measured as a function of thickness to assess the effectiveness of this film as a passivation layer and it applied to real devices. From this study, we can confirm that the passivation layer formed by TCFs using RF sputtering method sufficiently shows the potentiality of application to passivation layer for organic display devices.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1474-1476
• /
• 2005

ZnO:Al(AZO) has been investigated for the photovoltaic cell or TCO(Transparent Conductive Oxide) of the display, because it has good electrical and optical properties. In this study, the ZnO:Al(AZO) thin film prepared on variation of substrate temperature by FTS(Facing Targets Sputtering) system. In case of TCO, because resistivity and roughness values affect the lighting of the OLED, their factors are very important. Therefore, in this paper, the electrical and optical properties of the AZO thin film were investigated with the deposition conditions and its roughness was investigated on variation of the substrate temperature. In results, AZO thin film deposited with the transmittance over 80% and the resistivity was reduced from $1.36{\times}10^{-3}$ [O-cm] to $4{\times}10^{-4}$ [O-cm] with increasing the substrate temperature from R.T to $200[^{\circ}C]$. Especially, we could obtain the resistivity $4{\times}10^{-4}$ [O-cm] of AZO thin film prepared at working pressure 1[mTorr], input current 0.4[A] and substrate temperature $200[^{\circ}C]$.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.43-49
• /
• 2003

Low-temperature polysilicon (LTPS) technology has continued to mature with the passing of each year since LTPS mass production began. The integration of complex circuits has become possible with advances in microprocessing, leading to the realization of panels with highly advanced functions. At the same time, efforts have been made to meet market demands for lower costs, thereby boosting competitive strength. Today, LTPS-TFT LCDs have become standard equipment for the monitors of digital still cameras, and inroads are being made into the massive cellular phone market. Micro displays such as electronic viewfinders, which were previously only possible with high-temperature polysilicon technology, can now also be made with LTPS, thus expanding the scope of the technology. AMOLED displays using the LTPS-TFT as a back plane are also approaching the stage of industrialization. The hidden potential for the OLED to replace the familiar LCD has prompted Widespread anticipation for this emerging technology. This paper reflects on the history of LTPS technology, then looks forward to its future prospects and suggests a variety of potential fields of application.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.252-252
• /
• 2011

최근 주목받고 있는 amorphous gallium-indium-zinc-oxide (a-GIZO) thin film transistors (TFTs)는 수소가 첨가된 비정질 실리콘 TFT에 비해 높은 이동도와 뛰어난 전기적, 광학적 특성에 의해 큰 주목을 받고 있다. 또한 넓은 밴드갭을 가지므로 가시광 영역에서 투명한 특성을 보이고, 플라스틱 기판 위에서 구부러지는 성질에 의해 플랫 패널 디스플레이나 능동 유기 발광소자 (AM-OLED), 투명 디스플레이에 응용되고 있다. 뿐만 아니라, 일반적인 Poly-Si TFT는 자체적으로 가지는 결정성에 의해 대면적화 시 균일성이 좋지 못하지만 GIZO는 비정질상 이기 때문에 백플레인의 대면적화에 유리하다는 장점이 있다. 이러한 TFT를 제작하기 전, 전기적 특성에 대한 정보를 얻거나 예측하는 것이 중요한데, 이에 따라 고안된 구조가 바로 metal point contact FET (pseudo FET)이다. pseudo FET은 소스/드레인 전극을 따로 증착할 필요 없이 채널을 증착한 후, 프로브 탐침을 채널의 표면에 적당한 압력으로 접촉시켜 전하를 공급하는 소스와 드레인처럼 동작시킬 수 있다. 따라서 소스/드레인을 증착하거나 lithography와 같은 추가적인 공정을 요구하지 않아 소자의 특성을 보다 간단하고 수월하게 분석할 수 있다는 장점이 있다. 본 연구에서는 p-type 기판위에 100nm의 oxidation SiO2를 게이트 절연막으로 사용하는 a-GIZO pseudo FET를 제작하였다. 소자 제작 후, 열처리 온도에 따른 전기적 특성을 분석하였고, 열처리 조건은 30분간 N2 분위기에서 실시하였다. 열처리 후 전기적 특성 분성 결과, 450oC에서 가장 낮은 subthreshold swing 값과 게이트 전압의 더블 스윕 후 문턱 전압의 변화가 거의 없음을 확인하였다.

• Journal of the Semiconductor & Display Technology
• /
• v.5 no.3 s.16
• /
• pp.23-27
• /
• 2006

Recently, Top emission organic light-emitting diode (TEOLED) has been attracted by their potential application for the development of flat panel display (FPD). We have fabricated the high luminance top emission organic-emitting diode (TEOLED) using dual cathode layer and three top emitting structure. These devices were characterized by electroluminescence (EL) and current density-voltage (J-V) measurements. After compared it with Au anode structure, luminance of the device using dual anode was better than using without Al device. Consequently, Al layers are very good candidates for a promising electron-injecting buffer layer for top emission light-emitting diode (TEOLED).

• Journal of the Semiconductor & Display Technology
• /
• v.16 no.1
• /
• pp.1-5
• /
• 2017

Encapsulation of organic based devices is essential issue due to easy deterioration of organic material by water vapor. Thin layer of encapsulation film is required to preserve transparency yet protecting materials in it. Atomic layer deposition(ALD) is a promising solution because of its low temperature deposition and quality of the deposited film. $Al_2O_3$ or $Al_2O_3/TiO_2/Al_2O_3$ multilayer film has shown excellent environmental protection characteristics despite of thin thicknesses of the films. $Al_2O_3/TiO_2/Al_2O_3$ multilayer and 1.5 dyad layer of $Al_2O_3/polymer/Al_2O_3$ deposited by ALD was measured to have water vapor transmittance rate(WVTR) well below the detection limit($5.0{\times}10^{-5}g/m^2day$) of MOCON Aquatran 2 equipment.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.899-901
• /
• 2009

The magnesium fluoride ($MgF_2$) has very higher optical transmission than oxide or nitride material applied for gas barrier, so we manufactured Mg-Zn-F films with Mg-Zn-F target mixed in the various ratio of $MgF_2$ to Zn and characterized films' properties. Zn is used to increase packing density of barrier film. Thickness and optical transmission of Mg-Zn-F are 200 nm and over 90 %, respectively. The result of water vapor transmission rate at 38, RH 90 ~ 100% of the Mg-Zn-F film deposited with 4 : 6 ($MgF_2$ : Zn) ratio target reached below $1{\times}10^{-3}g$/($m^2{\cdot}day$), measuring limit of instrument.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.926-929
• /
• 2007

A significant progress has been made in the characterization of zinc oxide (ZnO) semiconductor as a new semiconductor layer instead of amorphous Si semiconductor used in thin film transistor due to its high electron mobility at low deposition temperature which is quite suitable for flexible display and OLED devices. The wet pattering of ZnO is another important issue with regard to mass production of ZnO thin film transistor device. However, the wet behavior of ZnO thin film in aqueous wet etching solutions conventionally used un TFT industry has not been reported yet, in this work, wet corrosion behavior of RF magnetron sputtered ZnO thin film in various wet solutions such as phosphoric and nitric acid solutions was studied using by electrochemical analysis. The effects of deposition parameters such as RF power and oxygen partial pressure on corrosion rate are also examined.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.155-158
• /
• 2007

Printed organic thin-film transistor(OTFT) to use as a switching device for an organic light emitting diode(OLED) were fabricated in the microcontact printing and direct printing processes at room temperature. The gate electrodes($5{\mu}m$, $10{\mu}m$, and $20{\mu}m$) of OTFT was fabricated using microcontact printing process, and source/drain electrodes ($W/L=500{\mu}m/5{\mu}m$, $500{\mu}m/10{\mu}m$, and $500{\mu}m/20{\mu}m$) was fabricated using direct printing process with hard poly(dimethylsiloxane)(h-PDMS) stamp. Printed OTFT with dielectric layer was formed using special coating system and organic semiconductor layer was ink-jet printing process. Microcontact printing and direct printing processes using h-PDMS stamp made it possible to fabricate printed OTFT with channel lengths down to $5{\mu}m$, and reduced the process by 20 steps compared with photolithography. As results of measuring he transfer characteristics and output characteristics of OTFT fabricated with the printing process, the field effect characteristic was verified.