• Transactions of the Korean Society of Automotive Engineers
• /
• v.1 no.1
• /
• pp.50-58
• /
• 1993

The ignition delay of diesel oil and fish oil blended with diesel oils was investigated at various pressure and temperature conditions in a constant volume combustion bomb. The evaporation and combustion duration of diesel oil and fish oil blended with diesel oils were respectively different in high and low temperature. The dependence of ignition delay on the temperature was different in high and low temperature ranges which were divided at the 773K. The dependence of ignition delay on the pressure was almost linear, regardless of the test fuels at the constant temperature(863K). The ignition delay became longer as the blending rate of fish oil increased at the constant temperature and pressure, but it was especially short with 20% fish oil blended with diesel oils.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.2 no.1
• /
• pp.34-39
• /
• 1999

Removal of spilled oil over the sea and the river has become one of the urgent problems in these days. Removing oil using mechanical devices by adhesion method is known to be closely related with the problem of estimating the thickness of film remaining on the surface of solid withdrawn from a quiescent liquid. In the present study a series of experimental results are compared with the analytic estimation for the thickness of film remaining on the solid surface using non-dimensional analysis. For the case of pure water both results show the remarkable agreement. However, discrepancy has been found for the case of Bunker C oil and diesel oil. The analytic estimation over-predicts the experimental value for the case of Bunker C oil and under-predicts it for the case of diesel oil. Further study is required to investigate the real situation including a contact angle and the property difference between oil and water.

• Geomechanics and Engineering
• /
• v.20 no.4
• /
• pp.299-312
• /
• 2020

The aim of this paper was to investigating the effects of soil relative density, construction materials roughness, oil type (gasoil, crude oil, and used motor oil), and oil content on the internal and interface shear behavior of sand with different construction materials by means of a modified large direct shear test apparatus. Tests conducted on the soil-soil (S-S), soil-rough concrete (S-RC), soil-smooth concrete (S-SC), and soil-steel (S-ST) interfaces and results showed that the shear strength of S-S interface is always higher than the soil-material interfaces. Internal and interface friction angles of sand beds increased by increase in relative density and decreased by increasing oil content. The oil properties (especially viscosity) played a major role in interface friction behavior. Despite the friction angles of contaminated sands with viscous fluids drastically decreased, it compensated by the apparent cohesion and adhesion developed between the soil grains and construction materials.

• Proceedings of the KSRS Conference
• /
• v.2
• /
• pp.985-988
• /
• 2006

Oil spills cause huge material damage. Oil and oil products spills may occur at any stage of the offshore oil production and transportation cycle. Therefore taking into account the current trends of oil production, the task of creating a system for shelf and tank fleet monitoring becomes very crucial today. This document describes the technology being implemented to improve oil spill monitoring and surveillance, to ensure SAR data fast acquisition and processing and to develop geographic information systems in support of spill response decision making. The results of technology implementation are also presented below.

• Tribology and Lubricants
• /
• v.13 no.4
• /
• pp.33-39
• /
• 1997

In order to establish a new temperature criterion to prevent the pistons from ring sticking due to deposit formation, bench test and engine test were performed. The effects of oil degradation and temperature on deposit formation was studied by a modified panel coking test. Oil degradation was analyzed by FTIR. Oil oxidation and nitration were selected as a factors to evaluate oil degradation. Bench test results show that oil oxidation is more effective to the deposit formation than oil nitration. And the temperature increase accelerates deposit formation and deposit formation increase rapidly above 26$0^{\circ}C$. Especially, in case of degraded oil, the deposit formation increases so rapidly that ring sticking can occur. The effect of piston temperature on the deposit formation was confirmed by engine test.

• Tribology and Lubricants
• /
• v.19 no.5
• /
• pp.280-284
• /
• 2003

High performance characteristics are required for rolling bearings and the various functions of bearing are greatly influenced by grease. Recently, higher performance is being demanded of rolling bearing greases for bearing lubrication. Four special greases with different composition such as lithium soap/ester oil, urea/ester oil, urea/ether oil and PTFE/fluorine oil were synthesized to compare the performance of these greases with that of the conventional lithium soap/mineral oil grease. The grease properties were investigated using a series of typical grease testing methods and grease life test. After the life test, the greases were charaterized by FTIR analysis and a microscope. And the iron amount in the greases was analyzed by AAS after ashing. The composition and manufacturing process determined the grease performance. The grease with a base oil of synthetic oil showed higher performance and the urea/ester oil and PTFE/fluorine oil showed about three times longer life as compared with conventional lithium grease.

• Tribology and Lubricants
• /
• v.23 no.1
• /
• pp.1-8
• /
• 2007

Turbocharger bearings are under the circumstance of high temperature, moreover rotated at high speed. It is necessary to be designed to overcome the high temperature. So the type of oil inlet port, the inlet oil temperature and the sort of engine oil should be designed, controlled and selected carefully in order to reduce the bearing inside temperature. Therefore, in this study, the effects of the type of inlet oil port, inlet temperature and the sort of engine oil on the performance of a turbocharger bearing are to be investigated. It is found that the type of oil inlet ports, the control of inlet oil temperature and the selection of engine oil type play important roles in determining the temperature and pressure, then the friction and load of a turbocharger journal bearing at high speed operation.

• Journal of the East Asian Society of Dietary Life
• /
• v.11 no.3
• /
• pp.204-208
• /
• 2001

This study was conducted to investigate physicochemical properties and anti-allergic properties of walnut oil. pH, acid value and iodine value of walnut oil were respectively 4.9, 0.8 and 117. Most of general composition of walnut oil was crude fat(99.9%) Vitamin A and E were 0.06 and 10.25mg/100g and the major fatty acids of walnut oil was linoleic acid(62.8%). Total phenolics and antiallergic effects of walnut oil were estimated 27mg% and 62.82% at the concentration of 0.5% ethanol walnut oil. These results suggest that the walnut oil can provide one of the valuable resource for the functional foods.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.49 no.5
• /
• pp.242-251
• /
• 2000

In this paper, we argued the possibility of the diagnostic technique for distribution transformers using the top oil temperature rising above the ambient temperature. The proposed diagnostic technique used the reference top oil temperature rising at rated current. We determined the emergency value of the transformer using the limitation of the top oil temperature rising and calculated the loss of life. The top oil temperature rises because of the load currents. In this point, the proposed diagnostic technique was explained. The proposed system measures the load current, top oil temperature and ambient temperature. With the diagnostic device, we tested the top oil temperature rising of t재 transformers. Then the loss of life was calculated by the top oil temperature.

• 유체기계공업학회:학술대회논문집
• /
• 2006.08a
• /
• pp.545-546
• /
• 2006

A problem of oil supply for a reciprocating compressor is very significant for an evaluation of reliability. Since a rotational motion of a crank shaft for the reciprocating compressor with small capacity is used for a power source of oil supply, a centrifugal force of the rotational shaft provides a stroke of oil inside the shaft like a centrifugal pump. The pumped oil rises following an inner wall and provided to a bearing passed through an oil supply hole at the side of the shaft for lubrication of the bearing. In this study, the amount of oil supply has been investigated by a numerical analysis for various conditions such as a shape of a groove, rpm of the compressor, and a shape of a flow channel. Also, a method of increasing oil supply for a low rpm has been studied so that the function can be improved for a variable condition.