• Progress in Medical Physics
• /
• v.17 no.2
• /
• pp.67-76
• /
• 2006

We evaluated the accuracy of a patient setup error correction due to reference image quality for a 2D-2D matching process. Digitally reconstructed radiographs (DRRs) generated by use of the Pinnacle3 and the Eclipse for various regions of a humanoid phantom and a patient for different CT slice thickness were employed as a reference images and kV X-ray Images from the On-Board Imager were registered to the reference DRRs. In comparison of the DRRs and profiles, DRR image quality was getting worse with an increase of CT image slice thickness. However there were only slight differences of setup errors evaluation between matching results for good and poor reference DRRs. Although DRR image quality did not strongly affect to the 2D-2D matching accuracy, there are still potential errors for matching procedure, therefore we recommend that DRR images are needed to be generated with less than 3mm slice thickness for 2D-2D matching.

• Journal of radiological science and technology
• /
• v.40 no.4
• /
• pp.613-620
• /
• 2017

Planning dose must be delivered accurately for radiation therapy. Also, It must be needed accurately setup. However, patient positioning images were need for accuracy setup. Then patient positioning images is followed by additional exposure to radiation. For 45 points in the phantom, we measured the doses for 6 MV and 10 MV photon beams, OBI(On Board Imager) and CBCT(Conebeam Computed Tomography) using OSLD(Optically Stimulated Luminescent Dosimeter). We compared the differences in the cases where posture confirmation imaging at each point was added to the treatment dose. Also, we tried to propose a photography cycle that satisfies the 5% recommended by AAPM(The American Association of Physicists in Medicine). As a result, a maximum of 98.6 cGy was obtained at a minimum of 45.27 cGy at the 6 MV, a maximum of 99.66 cGy at a minimum of 53.34 cGy at the 10 MV, a maximum of 2.64 cGy at the minimum of 0.19 cGy for the OBI and a maximum of 17.18 cGy at the minimum of 0.54 cGy for the CBCT.The ratio of the radiation dose to the treatment dose is 3.49% in the case of 2D imaging and the maximum is 22.65% in the case of 3D imaging. Therefore, tolerance of 2D image is 1 exposure per day, and 3D image is 1 exposure per week. And it is need to calculation of separate in the parallelism at additional study.

• The Journal of the Acoustical Society of Korea
• /
• v.27 no.2E
• /
• pp.35-44
• /
• 2008

The beat frequency is very important for the sound of Buddhist temple bells, but its concrete origins have not yet been fully clarified. In our research, we considered the beat of the bell at Hojobo Temple (Kanagawa Prefecture). Although its beat frequency has already been measured as 1.6 Hz, no satisfactory explanation has been offered for the factor that determines this value. In our previous research, we investigated the "Doza," the point where the bell is struck, and the "Obi," the vertical stripes around the bell, both of which are circumferential asymmetrical factors that can be visually recognized. Our investigations were carried out by using the Finite Element Method. These factors, however, could not sufficiently explain the beat frequency. Here, we first investigate the "Nyu," the many small projections on the bell, and the deviation between the centers of the inner and outer diameters of the bell. These two factors, however, were also found tobe insufficient explanations of the beat frequency. Through subsequent investigation, however, we finally clarified that the beat frequency's origin lies in the local dimension variation in the "Komazume," which is the bottom part of the bell as well as its thickest part.

• Journal of Pharmacopuncture
• /
• v.7 no.2
• /
• pp.97-105
• /
• 2004

Objectives : The purpose of this study is to compare the improvement rate in managering patients who had lumbago and pain in loin & feet by herbal-acupunture therapy with conservative treatment. Methods : 40patients who invited from March. 2003 to May. 2004 with lumbago and pain in loin & feet inve, were divided into two classes. A class was managed with conservative treatment(acupuncture, herb med, negative therapy, bed rest and physical therapy) and herbal-acupuncture therapy, the other class was managed with conservative treatment only. Two classes were distributed by sex and age, therapeutic periods, radiolographic results and therapeutic results that checked with VAS(visual analog scale) and ODI(Oswestry disability index). Results : According to VAS and OBI results, A class was managed with conservative treatment and herbal-acupuncture therapy shows the improvement in controling the pain of lumbago etc. comparing with the other class.

• Journal of the Korean Ceramic Society
• /
• v.30 no.11
• /
• pp.955-961
• /
• 1993

Sintering behavior and microstructure development in the system ZnO-Bi2O3-CoO-Zn7Sb2O12 with Zn7Sb2O12 content(0.1mol%~2mol%) were studied. The pyrochlore phase was formed by the reaction of the Zn7Sb2O12 with Bi2O3 phase during heating (below 90$0^{\circ}C$). The formation temperature of the liquid phase (Bi2O3) was dependent on the Zn7Sb2O12 contents (about 74$0^{\circ}C$ for Bi2O3/Zn7Sb2O12>1 by the eutectic melting in the ZnOBi2O3 system, and about 110$0^{\circ}C$ for Bi2O3/Zn7Sb2O12 1 by the decomposition of pyrochlore phase). Hence, sintering behavior and microstructure development were determined virtually by the Bi2O3/Zn7Sb2O12 ratio, which were promoted by liquid (Bi2O3) phase and retarded by the pyrochlore (or spinel) phase. The grain growth of ZnO during sintering was sluggish with increasing Zn7Sb2O12 contents.

• Radiation Oncology Journal
• /
• v.28 no.3
• /
• pp.155-165
• /
• 2010

Purpose: In order to evaluate the positional uncertainty of internal organs during radiation therapy for treatment of liver cancer, we measured differences in inter- and intra-fractional variation of the tumor position and tidal amplitude using 4-dimentional computed radiograph (DCT) images and gated orthogonal setup kilovolt (KV) images taken on every treatment using the on board imaging (OBI) and real time position management (RPM) system. Materials and Methods: Twenty consecutive patients who underwent 3-dimensional (3D) conformal radiation therapy for treatment of liver cancer participated in this study. All patients received a 4DCT simulation with an RT16 scanner and an RPM system. Lipiodol, which was updated near the target volume after transarterial chemoembolization or diaphragm was chosen as a surrogate for the evaluation of the position difference of internal organs. Two reference orthogonal (anterior and lateral) digital reconstructed radiograph (DRR) images were generated using CT image sets of 0% and 50% into the respiratory phases. The maximum tidal amplitude of the surrogate was measured from 3D conformal treatment planning. After setting the patient up with laser markings on the skin, orthogonal gated setup images at 50% into the respiratory phase were acquired at each treatment session with OBI and registered on reference DRR images by setting each beam center. Online inter-fractional variation was determined with the surrogate. After adjusting the patient setup error, orthogonal setup images at 0% and 50% into the respiratory phases were obtained and tidal amplitude of the surrogate was measured. Measured tidal amplitude was compared with data from 4DCT. For evaluation of intra-fractional variation, an orthogonal gated setup image at 50% into the respiratory phase was promptly acquired after treatment and compared with the same image taken just before treatment. In addition, a statistical analysis for the quantitative evaluation was performed. Results: Medians of inter-fractional variation for twenty patients were 0.00 cm (range, -0.50 to 0.90 cm), 0.00 cm (range, -2.40 to 1.60 cm), and 0.00 cm (range, -1.10 to 0.50 cm) in the X (transaxial), Y (superior-inferior), and Z (anterior-posterior) directions, respectively. Significant inter-fractional variations over 0.5 cm were observed in four patients. Min addition, the median tidal amplitude differences between 4DCTs and the gated orthogonal setup images were -0.05 cm (range, -0.83 to 0.60 cm), -0.15 cm (range, -2.58 to 1.18 cm), and -0.02 cm (range, -1.37 to 0.59 cm) in the X, Y, and Z directions, respectively. Large differences of over 1 cm were detected in 3 patients in the Y direction, while differences of more than 0.5 but less than 1 cm were observed in 5 patients in Y and Z directions. Median intra-fractional variation was 0.00 cm (range, -0.30 to 0.40 cm), -0.03 cm (range, -1.14 to 0.50 cm), 0.05 cm (range, -0.30 to 0.50 cm) in the X, Y, and Z directions, respectively. Significant intra-fractional variation of over 1 cm was observed in 2 patients in Y direction. Conclusion: Gated setup images provided a clear image quality for the detection of organ motion without a motion artifact. Significant intra- and inter-fractional variation and tidal amplitude differences between 4DCT and gated setup images were detected in some patients during the radiation treatment period, and therefore, should be considered when setting up the target margin. Monitoring of positional uncertainty and its adaptive feedback system can enhance the accuracy of treatments.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.21 no.4
• /
• pp.125-133
• /
• 2016

We investigated the distribution of organic matter and trace metals in surface sediment from Tonyeong coast. To determine the status of trace metal pollution, we also conducted an ecological risk assessment. Relatively high concentration of TN (total nitrogen), TOC (total organic carbon), and AVS (acid volatile sulfide) was found in surface sediment located in the narrow channel (site 35-38). Spatial distribution of Cd, Cr, Ni, Co, Hg, and Zn in surface sediment was similar and high Cu concentrations were found in narrow channel. The assessment of heavy metal pollution was derived using the Enrichment factors (EF). The enrichment factor indicated that Cd was no enrichment (EF<1), Pb, Cr, Ni, Co, Zn, and Hg were minor enrichment (1

• Journal of Fashion Business
• /
• v.11 no.5
• /
• pp.110-123
• /
• 2007

This study aims at analyzing the characteristics and the mode of deconstructionism expressed in fashion design centering on review of literatures and precedent researches. Through the review of previous studies and various articles, three major features with regard to deconstructionism were found: indeterminacy of meaning, decentralization, and inter -textuality. In fashion, the feature of indeterminacy of meaning expressed by non formula way such as unfinished, layering, obi or straight line cutting and it was divided into unstructured and unorganized factors. The feature of decentralization expressed by disorganization of sex, race, culture and humanism such as trans-gender, third world costume, sub-culture, posthumanism. Last, the feature of inter-textuality expressed by employing the fashion texts more than two simultaneously such as mixture of unmatched or unusual various clothing items, fabrics, patterns and styles. Non formality features in fahsion which divided into unstructured and unconstructed factors. The decentering of meaning means that disorganized the existing concepts of sex, race, culture and humanism features in fashion which divided into cross-gender, subculture, and post-humanism. Lastly, the feature of inter-textuality means that employed the fashion text more than two which is classified into factors of mixing mode and mixed styles. Unstructured factors were expressed by destroying the design principles such as balance, harmony and unit in fashion. Unconstructed factors were expressed by ignoring the basic costume structures and components in fashion. Cross-gender was expressed by manish and duality style in fashion and 3rd world costume was expressed by folk costume style. Anti fashion was expressed by anti aesthetics in fashion such as kitch, punk, and hippie styles. Post-human was expressed by futurism and the 4th Sex style in fashion. Mixing mode were expressed by mixture of item, and unmatched materials and pattern in fashion. Mixture of style were expressed by mixture of pastiche expression of various styles.

• Asian-Australasian Journal of Animal Sciences
• /
• v.23 no.9
• /
• pp.1244-1249
• /
• 2010

Comparisons of properties between skeletal ryanodine receptor 1 (sRyR1)-heterozygous-mutated and normal types of meat were carried out in pigs using PSE (pale, soft and exudative) meat found during the butchering process. All samples considered to be PSE meat showed irregular running and disorder of the muscle fibers and a wider inter-fiber space upon light microscopic observation. Electron microscopy revealed disintegration, twisting, and disorder of the myofibril arrangement and elimination of the Z line in PSE meat, compared with normal meat. Meat property tests demonstrated greater decreases in water holding capacity, moisture and sarcoplasmic protein, and higher $L^*$ values for the meat color index in PSE meat than in normal meat, but there were no differences in these factors between genetically normal and sRyR1-heterozygous PSE meat. On the other hand, higher $a^*$ and $b^*$ values were observed in sRyR1-heterozygous than in normal PSE meat, and similar alterations to the a* value were observed in terms of the amount of myoglobin and density of the 17-kDa protein band, corresponding to the molecular mass of myoglobin, on SDS-PAGE gels. These results suggest that sRyR1-heterozygous PSE pork contains much more myoglobin than genetically normal PSE meat.

• Fashion & Textile Research Journal
• /
• v.5 no.5
• /
• pp.443-452
• /
• 2003

People have been getting interested in the Orientalism and it has come up in various areas due to scientific progress. I designed uniforms, which was simple and western, to show its symbolic meanings in the Orientalism. And I have been trying to generalize uniforms with originality and beauty. I have studied the process of the Orientalism and its changes and transitions, concepts and origins in history. And I applied the styles of Korean, Japanese and Chineses costume on it. I also referred to characters of uniforms, which already had images of Korea, Japan and China. Firstly, Korean styles have a contrast in colors by application of Taegeuk. And they gave lines with dark colors in black one-piece dress. This makes people who are wearing looking slimmer. White ramie top looks fresh and Korean traditional tie called Maedeup is set up for button. Secondly, Japanese styles were mainly Kimono style, one piece. They changed into two pieces designed to be active. So, it has emphasized the image of Kimono with Obi at the waist. Thirdly, Chinese styles basically are Chipao style, which has a Chinese collar and a long skirt, which has opening. But they gradually changed into short skirts and more open in the chest. For one of them, they gave lines in the side of chest, sleeves and skirt to be more natural. The costumes have kept their positions as a part of mass society that grows and changes with speed. And oriental uniforms are not just uniforms any longer only for work. It is quite symbolic like a 'second face' as it represents images for their countries and enterprises.