• Wind and Structures
• /
• v.39 no.3
• /
• pp.207-222
• /
• 2024

This paper presents a numerical simulation method for snow drift that takes into account the cohesion effect of snow particles. The critical state of free collapse accumulation of idealized snow particles is used to indirectly infer the effect of interparticle interactions on snow transport and re-accumulation. With the help of the Hertz-Mindlin with JKR cohesion contact model, the particle angle of repose is calibrated with a number of contact parameters through numerical experiment. The surface energy for a given property of snow particles is determined using the observed snow angle of repose, and a continuous-discrete snow drift two-way coupled numerical model incorporating these optimized contact parameters is developed. The snow redistribution pattern on a stepped flat roof structure is simulated, and the results are found to be consistent with those of the field measured in terms of phenomena and general laws, verifying the achievability and effectiveness of the presented method. To eliminate the influence of environmental conditions, wind tunnel tests are also conducted, and it is found that the reconstructed depth and reaccumulated angle of snowdrift resulting from the numerical simulation are in closer agreement with the experimental results, further confirming the enhancement achieved by introducing the contact effect.

• Journal of computational fluids engineering
• /
• v.15 no.4
• /
• pp.53-59
• /
• 2010

Preliminary design of a ground plate, a device installed close to the aircraft model for wind tunnel test to simulate the ground effect, was performed by a numerical simulation. A two-dimensional numerical study was performed initially to decide the optimal leading edge and flap configurations. Then, three-dimensional studies were conducted to decide the optimal flap deflection angle for pressure distribution reduction since the plate and the plate supporting system generate static pressure difference between the upper and lower flow regions. Three-dimensional simulation additionally studied the effect of the clearance between the plate and the wind tunnel side wall. For the efficiency of computation, half model was simulated and a symmetric boundary condition was applied on the center plane. Based on the preliminary design, a ground plate was designed, manufactured and tested at the Korea Aerospace Research Institute(KARI) wind tunnel. The measured pressure differences versus flap deflection angle agreed well with the predicted results.

• Wind and Structures
• /
• v.25 no.5
• /
• pp.433-457
• /
• 2017

As a novel typical wind-sensitive structure, the wind load and wind-induced structural behaviors of super-large straight-cone cooling towers are in an urgent need to be addressed and studied. A super large straight-cone steel cooling tower (189 m high, the highest in Asia) that is under construction in Shanxi Power Plant in China was taken as an example, for which four finite element models corresponding to four structural types: the main drum; main drum + stiffening rings; main drum + stiffening rings + auxiliary rings (auxiliary rings are hinged with the main drum and the ground respectively); and main drum + stiffening rings + auxiliary rings (auxiliary rings are fixed onto the main drum and the ground respectively), were established to compare and analyze the dynamic properties and force transferring paths of different models. After that, CFD method was used to conduct numerical simulation of flow field and mean wind load around the cooling tower. Through field measurements and wind tunnel tests at home and abroad, the reliability of using CFD method for numerical simulation was confirmed. On the basis of this, the surface flow and trail characteristics of the tower at different heights were derived and the wind pressure distribution curves for the internal and external surfaces at different heights of the tower were studied. Finally, based on the calculation results of wind-induced responses of the four models, the effects of stiffening rings, auxiliary rings, and different connecting modes on the dynamic properties and wind-induced responses of the tower structure were derived and analyzed; meanwhile, the effect mechanism of internal suction on such kind of cooling tower was discussed. The study results could provide references to the structure selection and wind resistance design of such type of steel cooling towers.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.7 no.3
• /
• pp.466-477
• /
• 2015

In this study, a numerical prediction method on manoeuvrability of Wind Turbine Installation Vessel (WTIV) is presented. Planar Motion Mechanism (PMM) captive test for the bare hull of WTIV is carried out in the model basin and compared with the numerical results using RANS simulation based on Open-source Field Operation And Manipulation (OpenFOAM) calculation to validate the developed method. The manoeuvrability of WTIV with skeg and/or without skeg is investigated using the numerical approach along with the captive model test. In the numerical calculations, the dynamic stability index which indicates the course keeping ability is evaluated and compared for three different hull configurations i.e. bare hull and other two hulls with center skeg and twin skeg. This paper proves that the numerical approach using RANS simulation can be readily applied to estimate the manoeuvrability of WTIV at the initial design stage.

• KEPCO Journal on Electric Power and Energy
• /
• v.7 no.1
• /
• pp.145-152
• /
• 2021

Environmental change due to construction of large offshore wind farm has been a debate for a long time in Korea. There are various data acquired on hydrodynamics around this area before and during construction of offshore wind farm but no data during operation could be made due to delayed schedule. In this study, environmental change such as bathymetry change and scouring was forecasted using MIKE, numerical hydrodynamics model, and its results were validated using the observation data before and during construction.

• Wind and Structures
• /
• v.23 no.4
• /
• pp.313-350
• /
• 2016

Taipei 101 Tower, which has 101 stories with height of 508 m, is located in Taipei where typhoons and earthquakes commonly occur. It is currently the second tallest building in the world. Therefore, the dynamic performance of the super-tall building under strong wind actions requires particular attentions. In this study, Large Eddy Simulation (LES) integrated with a new inflow turbulence generator and a new sub-grid scale (SGS) model was conducted to simulate the wind loads on the super-tall building. Three-dimensional finite element model of Taipei 101 Tower was established and used to evaluate the wind-induced responses of the high-rise structure based on the simulated wind forces. The numerical results were found to be consistent with those measured from a vibration monitoring system installed in the building. Furthermore, the equivalent static wind loads on the building, which were computed by the time-domain and frequency-domain analysis, respectively, were in satisfactory agreement with available wind tunnel testing results. It has been demonstrated through the validation studies that the numerical framework presented in this paper, including the recommended SGS model, the inflow turbulence generation technique and associated numerical treatments, is a useful tool for evaluation of the wind loads and wind-induced responses of tall buildings.

• Journal of computational fluids engineering
• /
• v.10 no.1
• /
• pp.45-50
• /
• 2005

A fundamental understanding of the flow around the wind turbine is important to investigate the performance of new type of wind turbine. This study presents the simulation of three dimensional flow fields around the Darius wind turbine as an example. Incompressible Navier-Stokes equations are used for this simulation. The rotating coordinate system that rotates in the same speed of the turbine is used in order to simplify the boundary condition on the blades. Additionally, the boundary fitted coordinate system is employed in order to express the shape of the blades precisely. Fractional step method is used to solve the basic equations. Third order upwind scheme is chosen for the approximation of the non-linear terms since it can compute the flow field stably even at high Reynolds number without any turbulence models. The flow fields obtained in this study are highly complex due to the three dimensionality and are visualized effectively by using the technique of the computer graphics.

• Wind and Structures
• /
• v.16 no.6
• /
• pp.629-660
• /
• 2013

This paper reviews the current state-of-the-art in the numerical evaluation of wind loads on buildings. Important aspects of numerical modeling including (i) turbulence modeling, (ii) inflow boundary conditions, (iii) ground surface roughness, (iv) near wall treatments, and (vi) quantification of wind loads using the techniques of computational fluid dynamics (CFD) are summarized. Relative advantages of Large Eddy Simulation (LES) over Reynolds Averaged Navier-Stokes (RANS) and hybrid RANS-LES over LES are discussed based on physical realism and ease of application for wind load evaluation. Overall LES based simulations seem suitable for wind load evaluation. A need for computational wind load validations in comparison with experimental or field data is emphasized. A comparative study among numerical and experimental wind load evaluation on buildings demonstrated generally good agreements on the mean values, but more work is imperative for accurate peak design wind load evaluations. Particularly more research is needed on transient inlet boundaries and near wall modeling related issues.

• Atmosphere
• /
• v.17 no.4
• /
• pp.349-364
• /
• 2007

The main purpose of this study is to examine the sensitivity of the WRF (Weather Research and Forecasting) in the wind field to the steepness of mountains in the case with a strong downslope wind occurred in the Yeongdong province. We conducted WRF simulations for February 13 2006. The initial and boundary data are from the NCEP/NCAR $1^{\circ}{\times}1^{\circ}$ GDAS. Arbitrary terrains of the mountains with a symmetric orography and an asymmetric one with steeper leeward slope, were introduced to examine the sensitivity of the shape of the mountains. The simulation with an asymmetric terrain results in stronger maximum surface wind by about $10ms^{-1}$ than with a symmetric terrain, especially in the narrow region from the peak to ~ 4 km away in the downstream. However, the maximum surface wind speed is weaker by $20ms^{-1}$ than with a symmetric terrain away from the narrow peak region. This indicates that the steeper slope leads to the intensification of downslope wind in the narrower region leeward. In addition, for the simulation with an asymmetric terrain, the strength of wave breaking is greater and the Lee wave is more dominant than for that with a symmetric terrain.

• Wind and Structures
• /
• v.13 no.6
• /
• pp.519-528
• /
• 2010

A meteorological model, RAMS, and a commercial computational fluid dynamics (CFD) model, FLUENT are combined as a one-way off-line nested modeling system, namely, RAMS/FLUENT system. The system is experimentally applied in the wind simulation over a complex terrain, with which numerical simulations of wind field over Foyeding weather station located in the northwest mountainous area of Beijing metropolis are performed. The results show that the method of combining a meteorological model and a CFD model as a modeling system is reasonable. In RAMS/FLUENT system, more realistic boundary conditions are provided for FLUENT rather than idealized vertical wind profiles, and the finite volume method (FVM) of FLUENT ensures the capability of the modeling system on describing complex terrain in the simulation. Thus, RAMS/FLUENT can provide fine-scale realistic wind data over complex terrains.