• 대한토목학회논문집
• /
• 제31권5B호
• /
• pp.483-489
• /
• 2011

본 연구에서는 잠제 주변의 세굴 및 퇴적현상을 수치적으로 모의하기 위해 기존의 수치 파동 모델에 모래입자의 거동 해석을 위한 lagrangian 입자 모델을 결합한 새로운 수치모델을 개발하였다. 수치 파동 모델로서는 파랑에 의한 해저지반 내의 모래입자의 이동과 유동화 해석을 위해 투수성 매체 내부의 유체저항(관성저항, 층류저항 및 난류저항)을 고려할 수 있는 수치모델에 LES 난류모델을 도입한 수치해석기법(허와 최, 2008)을 이용하였다. 또한, 모래입자의 이동해석을 위한 lagrangian 입자 모델로서는 많은 개개의 입자들의 동적해석에 탁월한 개별요소법(Cundall and Strack, 1979)을 적용하였다. 개발된 해석기법을 이용하여 불투과 잠제 전면의 세굴에 대한 수치시뮬레이션을 실시한 후, 기존의 수리모형실험과 정성적으로 비교하면서 그 적용성을 검토하였다.

• 한국전자파학회논문지
• /
• 제16권4호
• /
• pp.389-396
• /
• 2005

본 논문에서는 OFDM 통신 시스템에서 발생하는 높은 PAPR(Peak to Average Power Ratio) 문제를 해결하기 위해 NLMS(Normalized Least Mean Square) 알고리즘을 이용한 전치왜곡 기법을 제안한다. 제안된 기법은 기본적으로, HPA(High Power Amplifier)치 비선형 왜곡 특성을 추정하고, HPA에 그와 반대되는 특성으로 신호를 변환하여 입력함으로써 비선형 왜곡에 대한 보상이 이루어진다. 뿐만 아니라, NLMS 알고리즘을 통하여 전치 왜곡기의 특성이 자동적으로 갱신되므로 HPA의 비선형 왜곡 특성의 변화에도 그에 맞는 정확한 보상이 이루어질 수 있다. 성능분석 결과, 제안된 NLMS 전치 왜곡기는 IBO(Input Back Off)가 $0\;\cal{dB}$일 경우, 기존의 적응성이 없는 수식적인 전치 왜곡기보다 약 $0.5\;\cal{dB}$의 SNR 손실을 보인다. 하지만 IBO가 $3\;\cal{dB}$ 이상에서 이들의 성능의 거의 같아지며, 제안된 전치 왜곡기는 HPA의 특성 변화에 적응성을 가지므로 실제 시스템에서 기존의 수식적인 전치 왜곡기보다 매우 효과적이라 할 수 있다.

• 한국수소및신에너지학회논문집
• /
• 제22권2호
• /
• pp.152-160
• /
• 2011

The electromagnetic characteristics of FCEVs (fuel cell electric vehicles) are much different from the existing combustion engine cars as well as hybrid, plug-in-hybrid, and pure electric vehicles due to the high voltage/current generated by a fuel cell stack which uses a compressed hydrogen gas reacted with oxygen. To operate fuel cell stack efficiently, BOP (Balance of Plant) which is consisted of many motors in water pump, air blower, and hydrogen recycling pump as well as inverters for these motors is essential. Furthermore, there are also electric systems for entertainment, information, and vehicle control such as navigation, broadcasting, vehicle dynamic control systems, and so on. Since these systems are connected by high voltage or general cables, EMC (Electromagnetic compatibility) analysis for high voltage and general cable of FCEV is the most important element to prevent the possible electric functional safety errors. In this paper, electromagnetic fields by high voltage and general cables for FCEVs is studied. From numerical analysis results, total time harmonic electromagnetic field strength from high voltage and general cables have difference of 13~16 dB due to ground effect by impedance matching. The EMI results of FECV at 10 m distance shows difference of 41 dB at 30 MHz and 54 dB at 230 MHz compared with only general cable routing.

• 한국통신학회논문지
• /
• 제21권12호
• /
• pp.3277-3285
• /
• 1996

In this paper, w designed an opical power distribution device for application to an optical switching and an optical subscriber loop. We fabricated PSG thin film by LPCVD. Based on the measured index of fabricted thin film, rib-type waveguide was transformed to two-dimension by the effective index method and we simulated dispersion property to find asingle-mode condition. We found that the optimum design parameters of rib-type waveguide are:cladding layer of 3.mu.m, core layer of 3.mu.m, buffer layer of 10.mu.m, and core width of 4.mu.m. Each side of the guiding region was etched down to 4.mu.m to shape the core. We used these optimum parameters of the rib-type waveguide with branching angle of 0.5.deg. and simulted the Y-branch waveguide by the BPM simulation. Numerical loss in branching area was claculated to be 0.1581dB and equal to the total loss of the Y-branch. The loss of the fabricated Y-branch waveguide on PSG film ws 1.6dB at .lambda.=1.3.mu.m before annealing but was 1.2dB after annealing at 1000.deg. C for 10 minutes. Consequently, the loss of branching area from 3000.mu.m to 6000.mu.m in the z-direction was 0.8dB, and single-mode propagation was confirmed by measuring the near field pattern. For coupling the fabricated Y-branch waveguide with an optical fiber, we fabricated V-groove which was used as the upholder of optical fiber. An etching angle was 54.deg. and the width and depth of guiding groove was 150.mu.m, 70.mu.m, respectively. The optical fiber is inserted onto V-groove. Both the Y-branch and V-groove were connected through the index matching oil. Coupling loss after connecting Y-branch and the optical fiber on V-groove was 0.34dB and that after injecting index mateching oil was 0.14dB.

• 한국통신학회논문지
• /
• 제28권7C호
• /
• pp.688-695
• /
• 2003

본 논문에서는, 적응형 필터를 이용한 동기획득 시스템을 실제 환경에 효과적으로 사용하기 위해 두 가지 알고리즘을 제안한다. 첫째, 하나의 필터를 여러 개의 부 필터로 나누어 적응시키는 병렬 부필터 탐색 구조를 제시하여 실제 환경에서 요구되는 빠른 동기 획득 성능을 얻는다. 둘째, 적응 파라미터들을 수신 신호의 전력에 따라 조절해주는 파라미터 결정기법을 제안하여 이상적인 성능에서 큰 열화 없이 실제 환경에서 효율적으로 동작 가능하도록 한다. 제안된 시스템에 대해 통계적인 분석을 수행하고 모의 실험을 통해 평균 동기 획득 시간 성능을 검증한다. 병렬 부필터 탐색 구조를 적용한 시스템은 기존의 전체 필터 탐색 구조에 비해 16탭에서 1∼l.5dB, 64탭에서 5∼6dB의 성능 이득을 보이며, 제안된 파라미터 결정기법을 적용한 시스템은 16탭과 32탭에서 이상적인 성능에서 약 1∼2.5dB 정도의 열화만으로 실제 환경에서 효과적으로 동작함을 보여준다.

• Korea-Australia Rheology Journal
• /
• 제21권1호
• /
• pp.47-58
• /
• 2009

We have investigated the transient behavior of 1D fully developed Poiseuille viscoelastic flow under finite pressure gradient described by the Oldroyd-B and Leonov constitutive equations. For analysis we employ a simple $2^{nd}$ order discretization scheme such as central difference for space and the Crank-Nicolson for time approximation. For the analysis of the Oldroyd-B model, we also apply the analytical solution, which is obtained again in this work in terms of elementary solution procedure simpler than the previous one (Waters and King, 1970). Both models demonstrate qualitatively similar solutions, but their eventual steady flowrate exhibits noticeable difference due to the absence or presence of shear thinning behavior. In the inertialess flow, the flowrate instantaneously attains a large value corresponding to the Newtonian creeping flow and then decreases to its steady value when the applied pressure gradient is low. However with finite liquid density the flow field shows severe fluctuation even accompanying reversals of flow directions. As the assigned pressure gradient increases, the flowrate achieves its steady value significantly higher than its value during oscillations after quite long period of time. We have also illustrated comparison between 1D and 2D results and possible mechanism of complex 2D flow rearrangement employing a previous solution of [mite element computation. In addition, we discuss some mathematical points regarding missing boundary conditions in 2D modeling due to the change of the type of differential equations when varying from inertialess to inertial flow.

• 대한토목학회논문집
• /
• 제30권5B호
• /
• pp.509-518
• /
• 2010

본 연구는 하천의 유역면적 또는 계획홍수량에 따라 하천 규모를 대 중 소하천으로 구분하고, 이들 하천에 대한 식생모델을 구축하여 수치모형을 이용해 제방고 여유율(CSR)을 기준으로 홍수위를 검토하였다. 식생모델 구축전 1차원 HEC-RAS와 2차원 RMA-2 모형을 이용하여 분석한 결과와 기본계획홍수위와 비교한 결과, 1차원의 경우 제방고 여유율은 대하천 모든 단면과 중하천 상류부 2개 단면 외에는 100% 이상이었으나, 소하천은 평균 46.0% 정도로 나타났다. 2차원 대하천의 경우는 평균 101.5%, 중하천은 96.7%, 소하천은 평균 71.1%로 나타났는데, 이는 하천기본계획수립 시 주로 1차원 모형을 사용하기 때문인 것으로 판단된다. 그러나 식생모델 적용 시 1차원에서는 대하천의 경우 평균 제방고 여유율은 91.8%, 중 소하천은 각각 74.2%, 38.3%로 나타났고, 2차원에서 대하천은 95.5%, 중 소하천은 각각 86.7%, 37.0%로 나타났다. 이는 대하천이 중 소하천 보다 유수단면적이 커 식생모델 적용 시 제방고 여유율의 영향을 적게 받기 때문인 것으로 판단된다.

• 대한기계학회논문집B
• /
• 제31권2호
• /
• pp.141-150
• /
• 2007

This paper presents a lumped model to predict crosstalk characteristics of thermally driven inkjet print heads. Using the lumped R-C model, heating characteristics of the head are predicted to be in agreement with IR temperature measurements. The inter-channel crosstalk is simulated using the lumped R-L network. The values of viscous flow resistance, R and flow inertance, L of connecting channels are adjusted to accord with the 3-D numerical simulation results of three adjacent jets. The crosstalk behaviors of a back shooter head as well as a top shooter head have been investigated. Predictions of the proposed lumped model on the meniscus oscillations are consistent with numerical simulation results. Comparison of the lumped model with experimental results identifies that abnormal two-drop ejection phenomena are related to the increased meniscus oscillations because of the more severe crosstalk effects at higher printing speeds. The degree of crosstalk has been quantified using cross-correlations between neighboring channels and a critical channel dimension for acceptable crosstalk has been proposed and validated with the numerical simulations. Our model can be used as a design tool for a better design of thermal inkjet print heads to minimize crosstalk effects.

• Structural Engineering and Mechanics
• /
• 제58권2호
• /
• pp.347-378
• /
• 2016

Within the scope of the plane-strain state, by utilizing the three-dimensional linearized theory of elastic waves in initially stressed piezoelectric and elastic materials, Lamb wave propagation and the influence of the initial stresses on this propagation in a sandwich plate with pre-stressed piezoelectric face and pre-stressed metal elastic core layers are investigated. Dispersion equations are derived for the extensional and flexural Lamb waves and, as a result of numerical solution to these equations, the corresponding dispersion curves for the first (fundamental) and second modes are constructed. Concrete numerical results are obtained for the cases where the face layers' materials are PZT-2 or PZT-6B, but the material of the middle layer is Steel (St) or Aluminum (Al). Sandwich plates PZT-2/St/PZT-2, PZT-2/Al/PZT-2, PZT-6B/St/PZT-6B and PZT-6B/Al/PZT-6B are examined and the influence of the problem parameters such as piezoelectric and dielectric constants, layer thickness ratios and third order elastic constants of the St and Al on the effects of the initial stresses on the wave propagation velocity is studied.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 추계학술대회 논문집
• /
• pp.136-140
• /
• 2000

It is desirable to predict springback quantitatively and accurately for the tool and process design in sheet stamping operations, however, it is blown very difficult. The result of springback analysis by the finite element method is sensitively influenced by numerical factors such as blank element size, number of integration point, punch velocity, contact algorithm etc. In the present work, a parametric study by Taguchi method is performed in order to evaluate the influence of numerical factors on springback Quantitatively and to obtain the combination of numerical factors which yields the best approximation to experimental data. Since springback is determined by the residual stress after forming process, it is important to evaluate stress distribution accurately. The oscillation in the time history curve of stress obtained by explicit FEM says that the stress solution at termination time is in very unstable state. Therefore, a variability study is also carried out in this study in order to assess the stability of implicit springback analysis starting from the stress solution by explicit forming simulation. The 2D draw bending process, one of the NUMISHEET '93 benchmark problems, is adopted as an application model.