• 한국유체기계학회 논문집
• /
• 제18권5호
• /
• pp.54-58
• /
• 2015

The objective of this paper is to investigate the flow characteristics of the multi nozzle. The configurations of the single, the 3- and the 6-nozzle were selected under Mach number of 2.5. Under-expanded pressure ratio such as 1.2, 1.6 and 2.0 were selected to elucidate interference of the free jet. The flow visualization was carried out with the Schlieren system and a supersonic cold-flow system. Also, the flow characteristics were studied computationally with the density measurements. Reasonable agreement between experimental and theoric equation has been achieved qualitatively.

• Journal of Advanced Marine Engineering and Technology
• /
• 제8권2호
• /
• pp.88-97
• /
• 1984

The combustion process and the performance of a diesel engine are considerably affected by the characteristics of fuel spray. It is known that the spray of swirl nozzle for diesel engine injector of small orifice ratio becomes soft spray that has no core, therefore its penetration, one of the characteristics of spray becomes werse inspite of its good dispersion. In this paper, the spray characteristics of variously designed swirl nozzle for diesel injector were investigated by the photographic method. The nozzles, used in this experiment, vary in the diameter of swirl chambers and orifice ratio. From the results of the study, the sprays of this type nozzle of optimum swirl chamber and orifice ratio show that penetration decreased slightly but dispersion and spray volume increased remarcably, compared with unswirled single hole nozzle of the same size. It was suggested as a reason for the results, that the spray of this type swirl nozzle is similar to hard spray, therefore the core of the spray sustains good penetration considerably.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.592-597
• /
• 2003

Thrust vector control using a coflow-counterflow concept is achieved by suction and blowing through a slot adjacent to a primary jet which is shrouded by a suction collar. In the present study, the flow characteristics of thrust vectoring is investigated using a numerical method. The nozzle has a design Mach number of 2.0, and the operation pressure ratio is varied to obtain various flow features of the nozzle flow. Test conditions are in the range of the nozzle pressure ratio from 6.0 to 10.0, and a suction pressure from 90kPa to 35kPa. Two-dimensional, compressible Navier-Stokes computations are conducted with RNG ${\kappa}-{\varepsilon}$ turbulence model. The computational results provide an understanding of the detailed physics of the thrust vectoring process. It is found that an increase in the nozzle pressure ratio leads to increased thrust efficiency but reduces the thrust vector angle.

• 한국유체기계학회 논문집
• /
• 제13권1호
• /
• pp.35-41
• /
• 2010

Experimental study on the flow field inside the nozzle for radial turbine was performed. At design point, the pressure is high and the Mach number is low at the pressure side of the nozzle inlet semi-vaneless space as the flow turns through the nozzle vanes. As the flow accelerates through the nozzle passage to the throat the pressure level at the pressure and suction sides becomes similar. The flow continued accelerating from the throat to the inlet of turbine wheel and the pressure field became uniform in the circumferential direction in the vaneless space. In high expansion ratio condition, strong favorable pressure gradient band region occurred just after the throat in the semi-vaneless space in the circumferential direction and the pressure became uniform in the circumferential direction after this band. In low expansion ratio condition, core flow acceleration is dominant after the throat and this non-uniform pressure field reached to the inlet of turbine wheel.

• 한국추진공학회지
• /
• 제6권2호
• /
• pp.1-7
• /
• 2002

추진기관은 노즐을 통해 추력을 발생하며 축소-확대 형상의 초음속 노즐에서는 노즐의 설계 팽창비가 내부 유동의 전압력과 배압의 압력비보다 매우 클 때 충격파의 발생과 함께 경계층 박리를 유발한다. 노즐 내부에서의 충격파 발생과 유동의 박리는 주어진 유동의 압력비에 가장 적합한 노즐형상을 구현하는 것으로 실제의 구조적 노즐의 형상보다 짧은 노즐에서 나타나는 유동과 같은 현상을 보인다. 수치 해석적 방법으로 고정된 형상의 2차원 노즐 내부의 충격파와 경계층 박리 현상에 관한 연구를 수행하였고 Hunter가 행한 실험적 연구와 비교하였다. 수치해석은 TVD 기법을 이용한 압축성 유체 해석 코드와 SST 2방정식 난류 모델을 이용하여 수행되었다. 낮은 압력비에서의 충격파와 경계층과의 상호작용에 의한 $\lambda$형태의 충격파 시스템을 잘 보여주고 있고 추력 값의 비교를 통해 고정된 형상의 노즐을 이용하여 필요한 운용범위를 충족할 수 있음을 알 수 있었다.

• 한국안전학회지
• /
• 제18권4호
• /
• pp.51-56
• /
• 2003

The goal of this study is to show the way to decrease the noise from air nozzles. The variables of this test are the shapes of air nozzles, air flow rate and the distance between a reflection plate and a nozzle tip. This experiment is aimed to find the most appropriate condition to minimize the noise. These are the results. If diameter ratio is more than 12:8, noise level increases by over 10 dB(A) regradless of the distance between a reflection plate and a nozzle and the existence of a reflection plate. And when $L_2$ of a nozzle is 5mm long, noise level rise relatively highly. So, it is strongly recommended that $L_2$ should be manufactured more than 10mm. The reason for a high intensity noise is that when diameter ratio is more than 12:8, the diameter of a nozzle tip($D_2$) turns small drastically, which increases the air velocity. It is assumed that when the vortes is great around the spots where a nozzle hole is suddenly smaller, great turbulent flow increases much noise.

• 대한기계학회논문집B
• /
• 제39권8호
• /
• pp.645-651
• /
• 2015

본 논문은 중앙구동 이젝터의 유량비에 미치는 설계변수의 영향에 대한 연구를 목적으로 한다. 중앙구동 이젝터의 설계변수는 구동노즐 출구 단면적 및 거리비, 디퓨저 출구 단면적비로 설정하였다. 실험장치는 가변노즐 이젝터, 전동 모터-펌프, 구동유체 저장수조, 제어판넬 그리고 고속 카메라 시스템으로 구성하였다. 유량비는 실험변수에 따라 측정되는 유입 공기량과 구동유체인 물의 유량을 이용하여 도출하였다. 유량비는 구동노즐 거리비와 혼합관 길이비가 커지면 증가하는 반면에, 구동노즐 면적비와 디퓨저 출구 면적비가 커지면 감소하였다.

• 한국분무공학회지
• /
• 제13권3호
• /
• pp.134-142
• /
• 2008

In the case of heavy duty diesel engines, the Urea-SCR system is currently considered to reduce the NOx emission as a proved technology, and it is widely studied to get the high performance and durability. However, the nozzles to inject the urea-water solution into the exhaust pipe occur some problems, including the nozzle clogging, deposition of urea-water solution on the inner wall of the exhaust pipe, resulting in the production of urea salt. In this study, a swirl-type twin-fluid nozzle to produce more fine droplets was used as a method to solve the problems. The effect of the nozzle cap geometry, including the length to diameter ratio ($l_o/d_o$) and chamfer, on the spray characteristics were investigated experimentally. The length to diameter ratio of nozzle cap were varied from 0.25 to 1.125. The chamfer angle of the nozzle cap was constant at 90o. The mean velocity and droplet size distributions of the spray were measured using a 2-D PDA (phase Doppler analyzer) system, and the spray half-width, AMD (arithmetic mean diameter) and SMD (Sauter mean diameter) were analyzed. At result, The larger length to diameter ratio of nozzle cap were more small SMD and AMD. The effect of the chamfer did increase the radial velocity, while it did not affect the atomization effect.

• 한국자동차공학회논문집
• /
• 제4권3호
• /
• pp.199-210
• /
• 1996

The measurements of velocities of internal flow in a scaled-up nozzle were made by laser Doppler velocimetry in order to clarify the effect of internal flow on the characteristics of fuel spray. The investigated length to diameter ratio(L/d) of the orifice were 1, 3, 4, 5 and 8, and inlet radius to diameter ratio(r0/d) were 0 and 0.5. Mean and fluctuating velocities and discharge coefficients were obtained at various Reynolds number ranging between 15,000 and 28,000, and L/d ranging between 1 and 8 in sharp and round inlet nozzle. The turbulent intensity and turbulent kinetic energy at exit in a sharp inlet nozzle were higher than that in a round inlet nozzle. For sharp inlet nozzle, fluctuating velocities near exit were decreased with increasing L/d.

• 한국분무공학회지
• /
• 제4권1호
• /
• pp.55-61
• /
• 1999

The first maximum point in the stability curve of liquid jet, i.e., the critical point is associated with the critical Reynolds number. This critical Reynolds number should be predicted by simple means. In this work, the critical Reynolds number in the stability curve of liquid jet are predicted using the empirical correlations and the experimental data reported in the literatures. The critical Reynolds number was found to be a function of the Ohnesorge number, nozzle lengh-to-diameter ratio, ambient Weber number and nozzle inlet type. An empirical correlation for the critical Reynolds number as a function of the Ohnesorge number and nozzle length-to-diameter ratio is newly proposed here. Although an empirical correlation proposed in this work may not be universal because of excluding the effects of ambient pressure and nozzle inlet type, it has reasonably agrees with the measured critical Reynolds number.