• 한국분무공학회지
• /
• 제16권2호
• /
• pp.90-96
• /
• 2011

Atomized liquid jets from the washing nozzle which configured with recirculation chamber for cleaning hot-zone area are accelerated and impinged on the head lamp surface. Cleaning efficiency of head lamp can be increased with injecting washing fluids into the hot-zone area. Experimental and numerical studies with various design parameters were executed to reveal the relations between internal geometry and internal flow in the washing nozzle. Spray structures were fitted with each of the head lamp surfaces and spray nozzles were optimized to the spray pattern. The recirculation chamber induces a recirculation flow and can be decreased the pressures perturbation inside the chamber. Orifice determines the mass flow rate. When the diameter of orifice is excessively large, it showed an unstable spray pattern. As a nozzle exit angle increases, density distributions are separated with two section. Also, as a protrusion length of nozzle exit increases, spray patterns are spread into a large area and density distributions showed unstable trend.

• 한국전산유체공학회지
• /
• 제14권1호
• /
• pp.78-85
• /
• 2009

A combined theoretical and numerical study is conducted to design a slit nozzle for large-area liquid coating. The objectives are to guarantee the uniformity in the injected flow and to provide the capability of explicit control of flow rate. The woking fluid is a dilute aqueous solution containing single-walled carbon nanotubes and its low viscosity and the presence of dispersed materials pose technical hurdles. A theoretical analysis leads to a guideline for the geometric design of a slit nozzle. The CFD-based numerical experiment is employed as a verification tool. A new flow passage unit, connected to the nozzle chamber, is proposed to permit the control of flow rate by using the commodity pressurizer. The numerical results confirm the feasibility of this idea. The optimal geometry of internal structure of the nozzle has been searched for numerically and the related issues are discussed.

• 한국분무공학회지
• /
• 제2권2호
• /
• pp.35-42
• /
• 1997

An innovating technique of atomizer has been proposed to supply and to atomise molten materials. Both of a simple geometry of nozzle and an improved nozzle have been fabricated in the present study. With these nozzles, characteristics of the suction and disintegration have been empirically investigated. The important conclusions are as follows; In the case of a simple nozzle: 1) Although the sucking up and supplying of molten materials are available, the applications of powder metallurgy are limited. 2) It is concluded that the more air flow rate, $W_A$ or the shorter the height of air nozzle from the surface of supplied water, $L_h$, the more the atomizing mass of liquids, $W_L$. In the case of an improved nozzle: 3) The stable liquids can be supplied due to cut off the passage of surrounding air entrainment by air jets. 4) The atomizing mass of liquids, $W_L$ has affected not so much on the height of nozzle from the surface of supplied water, $L_h$ as that from the orifice, hc.

• 한국음향학회지
• /
• 제41권6호
• /
• pp.698-704
• /
• 2022

본 논문에서는 노즐 내부 유동의 소음원으로부터 발생되어 방사되는 공력 소음을 정량적으로 분석하였으며, 이를 외부 방사소음 결과와 비교하였다. 세가지 종류의 노즐 형상에 대해 내부 및 외부 유동을 정확히 예측하기 위해 고해상도 수치해석 기법인 비정상 압축성 대와류모사(Large Eddy Simulation, LES) 기법을 사용하였다. 와류소음원(Vortex Sound Source)을 통해 유동소음원을 확인하였으며, 이를 통해 노즐 내부 형상에서 주요 유동소음원의 분포를 확인하였다. 노즐 내부 유동의 와류소음원 레벨과 외부 방사 소음의 예측결과 및 측정결과와 비교하였으며, 이를 통해 정량적 분석을 검증하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제27권6호
• /
• pp.745-752
• /
• 2003

Injection technology is one of the important technologies in a diesel engine. Many studies have done on the injection system. In this study, the fuel chamber geometry, the orifice ratio and the needle lift of the injection valve of a diesel engine for generating electricity are varied and tested. The injection pressure, duration and spray shapes are produced with pressure transducer, needle lift sensor and highspeed camera. The result shows that the nozzle hole size has influence on the rail pressure and injection duration sensuously.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2763-2768
• /
• 2007

Recently, as the semiconductor production technology develops, there has been growing interest in the cooling system using micro fluid pump. Among the various types of micro fluid pump, the valve-less diffuser/nozzle has been extensively studied in recent years. However, the flat-walled diffuser/nozzle flow has not been clearly looked into due to its non-linear characteristics. In this paper, the flow characteristics of the flat-walled diffuser/nozzle have been analyzed using similitude model and simulations. Similitude models are designed so that the flow pattern is same as that of 1/10 scale flow by using high viscous fluid as working fluid. The results are compared to the simulations. It is shown that the flow characteristics of 2D simulation are different from 3D simulations at high Re region, and the measured pump efficiency is highly dependent on the pressure difference as well as the channel geometry. From these results, the desirable conditions for the efficient pump is discussed.

• 한국추진공학회지
• /
• 제3권2호
• /
• pp.37-47
• /
• 1999

본 논문은 노즐내열재의 삭마로 인해 야기된 형상변화를 고려하면서 로켓노즐 내열재의 삭마량 및 온도분포를 해석하는 열반응해석에 대해 기술하였다. 열반응 해석에서 표면 삭마는 Zvyagin의 모델을, 내부 열분해는 Yaroslavtseva의 모델을 사용하였다. 노즐내열재의 형상변화로 인한 경계면 이동을 고려하기 위하여 변형가능한 유한요소 격자를 사용하였다. 본 수치해석기법의 타당성을 입증하기 위해 로켓 노즐내열재에 대해 열해석을 수행하였으며, 그 결과 수치해는 실험결과와 잘 일치함을 보였다. 노즐내열재에서의 시간에 따른 온도변화 및 삭마량을 계산하고 고찰하였으며 또한 탄소/탄소 내열재 및 탄소/페놀릭 내열재의 열반응상수가 노즐내열재의 삭마량에 미치는 영향에 대해서 검토하였다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제37회 추계학술대회논문집
• /
• pp.206-212
• /
• 2011

유체 시스템에서 히스테리시스 현상은 다양한 산업 및 공학의 응용 분야에서 발생하며, 주로 압력비의 시간변화 과정에서 발생한다. 초음속 노즐에서 충격파를 포함한 유동장은 이러한 히스테리시스 현상의 지배적인 영향을 받는다. 그러나 이와 관련된 유동의 물리적 현상에 대해서는 연구가 미비한 실정이다. 본 연구에서는 노즐구동압력비의 변화 과정 동안 초음속 노즐의 유동을 파악하기 위해 실험적 연구를 수행하였다. 순간 표면압력을 측정하기 위하여 다수의 압력변환기를 사용하였으며, 유동장의 가시화는 나노스파크 광원을 가지는 쉴리렌 가시화 장치를 이용하였다. 본 연구로부터, 히스테리시스 현상은 노즐의 기하학적 형상뿐만 아니라 압력비의 시간변화에 크게 의존하였다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2006년도 PARALLEL CFD 2006
• /
• pp.395-397
• /
• 2006

Air interlacing serves to protect the yarn against damage, strengthens inter-filament compactness or cohesion, and ensures fabric consistency. The air interlacing nozzle is used to introduce intermittent nips to a filament yarn so as to improve its performance in textile processing. The effect of various interlacing nozzle geometries on the interlacing process was studied. The geometries of interlacing nozzles with single or multiple air inlets located across the width of yarn channels are investigated. The basis case is the yarn channel, with a perpendicular main air inlet in the middle. Other cases have main air inlets, slightly inclined double sub air inlets, The yarn channel cross sectional shapes are either semicircular or rectangular shapes. The compressed impinging jet from the main air inlet hole hits the opposing bottom wall of the yarn channel, is divided into two branches, joins with the compressed air coming out from sub air inlet at the bottom and creates two free jets at both ends of the yarn channel. The compressed air movement in the cross-section consists of two opposing directional vortices. The CFD-FASTRAN flow parallel solver was used to perform steady simulations of impinging jet flow inside of the interlace nozzles. The vortical structure and the flow pattern such as pressure contour, particle traces, velocity vector plots inside of interlace nozzle geometry are discussed in this pater.

• 한국유체기계학회 논문집
• /
• 제12권6호
• /
• pp.13-17
• /
• 2009

Ejector is an equipment devised for making use of the low pressure occurring from the fast fluid injection and it is a transportation equipment which can obtain vacuum using the kinetic energy of the fluid. This ejector system is, nowadays, widely used for construction machinery, heavy equipments, the cooling and ventilation of electronic devices and for the various fluid transportation and pumps. In this study, it is attempted to perform a numerical analysis and an experiment to find out the characteristics of fluid quantity, velocity and the pressure distribution of the induction pipe by changing the length and the radius ratio of the nozzle of ejector. From the results, it is investigated that the distributions of velocity and pressure of induction pipe attached are changing with the length and the radius ratio of the nozzle. In addition, it is shown that for the small and large ejector, the efficiency is the maximum when the length of the nozzle arrived to the neck of the ejector, however, if it is installed at below or above the neck the efficiency is rather decreased.