• Journal of the Korean Society of Combustion
• /
• v.1 no.1
• /
• pp.41-49
• /
• 1996

Effects of ambient geometry on the liftoff characteristics are experimentally studied for nonpremixed turbulent jet flames. To clarify the inconsistency of the nozzle diameter effect on the liftoff height, the ambiences of finite and infinite domains are studied. For nonpremixed turbulent jet issuing from a straight nozzle to infinite domain, flame liftoff height increases linearly with nozzle exit mean velocity and is independent of nozzle diameter. With the circular plate installed on the upstream of nozzle exit, flame liftoff height is lower with plate at jet exit than without, but flame liftoff characteristics are similar to the case of infinite domain. For the confined jet having axisymmetric wall boundary, the ratio of the liftoff height and nozzle diameter is proportional to the nozzle exit mean velocity demonstrating the effect of the nozzle diameter on the liftoff height. The liftoff height increases with decreasing outer axisymmetric wall diameter. At blowout conditions, the blowout velocity decreases with decreasing outer axisymmetric wall diameter and liftoff heights at blowout are approximately 50 times of nozzle diameter.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.4
• /
• pp.519-525
• /
• 2000

The effect of nozzle diameter on the local Nusselt number distributions has been investigated for an axisymmetric turbulent jet impinging on the flat plate surface. The flow at the nozzle exit has a fully developed velocity profile. A uniform heat flux boundary condition at the plate surface was created using gold film Intrex. Liquid Crystal was used to measure the plate surface temperature. The experiments were made for the jet Reynolds number (Re) 23,000, the dimensionless nozzle to surface distance (L/d) from 2 to 14, and the nozzle diameter (d) from 1.36 to 3.40 cm. The results show that the Nusselt number at and near the stagnation point increase with an increasing value of the nozzle diameter.

• Journal of ILASS-Korea
• /
• v.17 no.3
• /
• pp.140-145
• /
• 2012

Recent common-rail injector of a diesel engine needs more smaller nozzle hole to meet the stringent emission regulation. But, small nozzle hole diameter can cause nozzle coking which is occurred due to the deposits of post-combustion products. Nozzle coking has a negative effect on the performance of fuel injector because it obstructs the fuel flow inside a nozzle hole. In this study DFSS (Design for six sigma) method was applied to find the effect of nozzle design parameter on nozzle coking. Total 9 injector samples were chosen and tested at diesel engine. The results show that nozzle hole diameter and K-factor have more effect on nozzle coking than A-mass and hole length. Large hole diameter and A-mass, small hole length and K-factor give more positive performance on nozzle coking in these experimental conditions. But, a performance about nozzle coking and exhaust gas emission shows the opposite tendency. Further study is needed to find the relation between nozzle coking and emission characteristic for the optimization of injector nozzle design.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.17 no.3
• /
• pp.3872-3877
• /
• 1975

This study was conducted to examine the effects of the change of cap hole diameter and pressure on the travelling distance and the sprayed particle size for the medium range nozzle. The results of this study are summarized as follows; 1) The effective travelling distance was about from 1 meter to 8 meters and centro-position of the travelling distance was about 3 or 5 meters. 2) Main effect of change of cap hole diameter for the travelling distance was a slight convex quadratic curve. 3) Main effect of change of pressure increased linearly, its increasing rate about 1.6 was large. 4) Sizes of sprayed particles were less than 250${\mu}$ generally and the sizes decreased according to the increasing of travelling distance. 5) Changes of diameter of sprayed particles by cap hole diameter increased in accordance with increasing of cap hole diameter. 6) Changes of diameter of sprayed particles by the groove depth of swirl plate was very slight.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.3 s.258
• /
• pp.264-272
• /
• 2007

The aim of this study is to investigate the effects of nozzle orifice shapes and the nozzle length-to-diameter ratio(L/D) on the nozzle cavitation formation inside the orifice and the external flow pattern. The nozzle used in this work was tested the taper orifice nozzle and the rectangular orifice nozzle which was made from the transparent acrylic acid resin. For studying the effect of the nozzle L/D ratio, it was used to three L/D ratios of 3.33, 10, and 20. The cavitation flow of nozzle was visualized by using the ICCD camera and optical system. This work revealed that the flow rate and discharge coefficient($C_d$) of the taper orifice nozzle was larger than those of the rectangular orifice nozzle at the same injection pressure. The cavitation flow was observed in the nozzle orifice at the low injection pressure and the breakup of liquid jet was promoted as the L/D ratio is decreased. The cavitation of biodiesel fuel was formed at the lower injection pressure than that of diesel fuel because of higher viscosity and density.

• Journal of ILASS-Korea
• /
• v.13 no.3
• /
• pp.134-142
• /
• 2008

In the case of heavy duty diesel engines, the Urea-SCR system is currently considered to reduce the NOx emission as a proved technology, and it is widely studied to get the high performance and durability. However, the nozzles to inject the urea-water solution into the exhaust pipe occur some problems, including the nozzle clogging, deposition of urea-water solution on the inner wall of the exhaust pipe, resulting in the production of urea salt. In this study, a swirl-type twin-fluid nozzle to produce more fine droplets was used as a method to solve the problems. The effect of the nozzle cap geometry, including the length to diameter ratio ($l_o/d_o$) and chamfer, on the spray characteristics were investigated experimentally. The length to diameter ratio of nozzle cap were varied from 0.25 to 1.125. The chamfer angle of the nozzle cap was constant at 90o. The mean velocity and droplet size distributions of the spray were measured using a 2-D PDA (phase Doppler analyzer) system, and the spray half-width, AMD (arithmetic mean diameter) and SMD (Sauter mean diameter) were analyzed. At result, The larger length to diameter ratio of nozzle cap were more small SMD and AMD. The effect of the chamfer did increase the radial velocity, while it did not affect the atomization effect.

• Fashion & Textile Research Journal
• /
• v.1 no.2
• /
• pp.166-172
• /
• 1999

An experimental investigation has done for studying the changes of physical properties of the air-jet textured polyester yarn. Through the experiments of polyester 85/72 drawn yarn and 50/36 partially oriented yarn doubling' the following results are obtained. The tenacity of textured yarn decreased as the number of tension rings increased when the nozzle diameter was 1.2 mm. In the case when the tension ring was not used during the texturing process, the tenacity of textured yarn decreased as the nozzle diameter increased. But this tendency changed according to the number of tension rings used, the diameter of the nozzle, and yarn take-up speed. Breaking elongation decreased as the number of tension rings increased from one to four and the take-up speed increased at diameter 1.2 mm of the nozzle. The higher the diameter of the the nozzle the higher the breaking elongation until 1.4 mm. The number of interlacing went down as the diameter of the nozzle increased and the take-up speed of the yarn increased. The higher the number of tension rings, the lower the number of interlacing.

• 유체기계공업학회:학술대회논문집
• /
• 2002.12a
• /
• pp.331-336
• /
• 2002

Recently the critical nozzles with small diameter are being extensively used to measure mass flow in a variety of industrial fields and these have different configurations depending on operation condition and working gas. The curvature radius of the critical nozzle throat is one of the most important configuration factors promising a high reliability of the critical nozzle. In the present study, computations using the axisymmetric, compressible, Navier-Stokes equations are carried out to investigate the effect of the nozzle curvature on critical flows. The diameter of the critical nozzle employed is D=0.3mm and the radius of curvature of the critical nozzle throat is varied in the range from 1D to 3D. It is found that the discharge coefficient is very sensitive to the curvature radius(R) of critical nozzle, leading to the peak discharge coefficient at R = 2.0D and 2.5D, and that the critical pressure ratio increases with the curvature radius.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.4
• /
• pp.94-100
• /
• 2007

The purpose of this work is to investigate the effect of properties of diesel and biodiesel fuels on the nozzle cavitation and the effect of the length/diameter(L/D) ratio on internal and external flow pattern of nozzle at the various injection conditions. In order to study the effect of the L/D ratio on the nozzle cavitation characteristics of diesel and biodiesel, the characteristics of cavitation flow in the nozzle are visualized and analyzed at the injection pressure of 0.1 MPa to 0.7 MPa by using the visualized images. It was founded that the cavitation was formed in the nozzle orifice at the low injection pressure and the breakup of the issuing liquid jet was promoted at the low L/D ratio. When the L/D ratio decrease, cavitation beginning and growth were affect by cavitation number and Reynolds number.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.15 no.3
• /
• pp.3053-3058
• /
• 1973

1. This study was conducted to examine the effects of change of the short range nozzle hole on the travelling distance. The results of this study are summarized as follows; a) Effect of change of the cap hole diameter on the travelling distance of sprayed particles was generally a linear, the increasing rate was about 0.27. b) When the difference between the sectional area of cap hole and that of grooves of swirl plate, was small the travelling distance was decreased by the decreasing of spraying speed at cap hole. 2. This study was conducted to examine the effects of change of the short range nozzle hole on the size of spraying particles. The results of this study are summarized as follows; a) The diameter of sprayed particles on travelling distances in the short range nozzle did not coincide with the kinetic energy principle derived from the momentum and the resistance. b) The average diameter of sprayed particle between 1m and 3m in which amount of sprayed particle was particularly a great deal, was big, because that some of sprayed particles were absorbed each other on the way to fall c) Effect of increase of cap hole diameter was generally enlarged the average diameter of sprayed particle with small rate.