• Transactions of The Korea Fluid Power Systems Society
• /
• v.8 no.3
• /
• pp.14-20
• /
• 2011

This study aims at aligning multiple wafers to reduce wafer handling time in wafer processes. We designed a multilevel structure for a prealigner which can handle multiple wafer simultaneously in a system. The system consists of gripping parts, kinematic parts, vacuum chucks, pneumatic units, hall sensors and a DSP controller. Aligning procedure has two steps: mechanical gripping and notch finding. In the first step, a wafer is aligned in XY directions using 4-point mechanical contact. The rotational error can be found by detecting a signal in a notch using hall sensors. A dual prealigner was designed for 300mm wafers and constructed for a performance test. The accuracy was monitored by checking the movement of a notch in a machine vision. The result shows that the dual prealigner has enough performance as commercial products.

• Proceedings of the KOR-BRONCHOESO Conference
• /
• 1981.05a
• /
• pp.39.3-40
• /
• 1981

Concerning the pathogenesis of acquired cholesteatoma in attic, there has been postulated theories by immigration from the Shrapnell's portion of the tympanic membrane, posterosuperior quardrant of the deep meatal skin and invagination of the margin of the central perforation. Otherwise, squamous metaplasia of the epithelium lining the middle ear cleft has been supported as a possible cause of cholesteatoma. Clinically, there has been known of the facts that cholesteatoma is formed in the attic but the pathogenesis concerning the acquired cholesteatoma is not still exactly reported. Recently, authors analyzed 170 cases of cholesteatomatous middle ear performed the operation to the middle ear cleft. On the operation finding, when the primary focus of the cholesteatoma was in the attic, we observed two types of perforation, marginal and central perforation in the Shrapnell's portion, and retraction to the Prussak's space, bony defect on the Rivinus notch. Among 36 cases of the cholesteatoma, the perforation of the Shrapnell's portion are 5 cases. Bony defect on the Rivinus notch and marginal perforation on the posterosuperior quadrant of the Shrapnell's portion are 21 cases. Among these cases, 3 cases are combined with central perforation of the Shrapnell's portion. Conclusively, the reasons that cholesteatoma is favorable site in the attic: 1) Excretion of the inflammatory discharge in the attic is difficult because of the distance of the E-tube. 2) The Shrapnell's portion has less collagen fiber than the pars tensa and it is thin because the elastic fibers are rich in it. It is easy to retract within the Prussak's space to the cases of keratinizing hyperplasia. 3) The epidermis attached at the Rivinus notch of the superior portion on the Shrapnell's portion is invaginated through the destructed bony wall of the Rivinus notch and the margin of the tympanic membrane in the response to the keratinizing hyperplasia.

• Imaging Science in Dentistry
• /
• v.46 no.1
• /
• pp.47-51
• /
• 2016

Herein, we report and discuss the detection of fossa navicularis magna, a close radiographic anatomic variant of canalis basilaris medianus of the basiocciput, as an incidental finding in cone-beam computed tomography (CBCT) imaging. The CBCT data of the patients in question were referred for the evaluation of implant sites and to rule out pathology in the maxilla and mandible. CBCT analysis showed osseous, notch-like defects on the inferior aspect of the clivus in all four cases. The appearance of fossa navicularis magna varied among the cases. In some, it was completely within the basiocciput and mimicked a small rounded, corticated, lytic defect, whereas it appeared as a notch in others. Fossa navicularis magna is an anatomical variant that occurs on the inferior aspect of the clivus. The pertinent literature on the anatomical variations occurring in this region was reviewed.

• Structural Engineering and Mechanics
• /
• v.34 no.3
• /
• pp.367-376
• /
• 2010

In this paper, an experimental investigation of the mechanical behavior and buckling failure of sharp-notched circular tubes subjected to cyclic bending is discussed. The unnotched and sharp-notched circular tubes of SUS 304 stainless steel were tested under symmetric curvature-controlled cyclic bending. It was found from moment-curvature curves that the loops show cyclic hardening and gradually steady after a few cycles for all tested tubes. The ovalization-curvature curves show an unsymmetric, ratcheting and increasing manner with the number of cycles. In addition, it was found that six almost parallel lines corresponding to unnotched and five different notch-depth (0.2, 0.4, 0.6, 0.8 and 1.0 mm) tubes were noted from the experimental relationship between the cyclic controlled curvature and the number of cycles necessary to produce buckling on a log-log scale. An empirical formulation was proposed so that it could be used for simulating the aforementioned relationship. By comparing with the experimental finding, the simulation was in good agreement with the experimental data.

• International Journal of Automotive Technology
• /
• v.2 no.1
• /
• pp.9-16
• /
• 2001

The lifetime of power train components can be improved dramatically by finding crack initiation points with suitable software tools and optimization of the critical areas. With increasing capacities of computers the prediction of the lifetime for components by numerical methods gets more and more important. This paper discusses some applications of the outstanding fatigue simulation program FEMFAT supporting the assessment of uniaxially and multiaxially loaded components (as well as welding seams and spot joints). The theory applied in FEMFAT differs in some aspects from classical approaches like the nominal stress concept or the local one and can be characterized by the term "influence parameter method". The specimen S/N-curve is locally modified by different influence parameters as stress-gradient to take into account notch effects, mean-stress influence which is quantified by means of a Haigh-diagram, surface roughness and treatments, temperature, technological size, etc. It is possible to consider plastic deformations resulting in mean-stress rearrangements. The dynamic loading of power train components is very often multiaxial, e.g. the stress state at each time is not proportional to one single stress state. Hence, the directions of the principal axes vary with time. We will present the way how such complex load situations can be handled with FEMFAT by the examples of a crank case and a gear box.

• Journal of the Korean Arthroscopy Society
• /
• v.5 no.2
• /
• pp.63-68
• /
• 2001

Purpose : To propose the diagnosis, 'hypertrophy of the anterior cruciate ligament(ACL)', and its clinical, radiological and pathological characteristics. Materials & Method : Since Dec. 1995, we have experienced 10 patients(12 knees) with hypertrophy of the ACL. There were 2 males and 8 females, and the age of the patients ranged from 35 to 67 years. Characteristics of clinical, radiological and pathological findings were analysed. Results : The chief complaint was insidious onset of dull pain on the knee which became worse with activity. The constant physical finding was painful limitation of full extension of the knee. Sagittal MR images showed diffuse swelling of the ACL, similar finding that could be seen in acute ACL tear. Arthroscopically, noted was a marked enlargement of the ACL causing notch impingement. Biopsies of the hypertrophied ACL showed increased collagenous tissue with variable degree of myxoid degeneration. With partial excision of the hypertrophied ACL with or without notchplasty, the symptoms improved in all. Conclusion : Hypertrophy of the ACL, a newly proposed diagnosis, should be considered be determining the cause of the painful knee, and further study should be done about its pathogenesis.

• Advances in aircraft and spacecraft science
• /
• v.5 no.2
• /
• pp.225-237
• /
• 2018

The difficulties of satellite vibration testing are due to the commonly expressed qualification requirements being incompatible with the limited performance of the entire controlled system (satellite + interface + shaker + controller). Two features cause the problem: firstly, the main satellite modes (i.e., the first structural mode and the high and low tank modes) are very weakly damped; secondly, the controller is just too basic to achieve the expected performance in such cases. The combination of these two issues results in oscillations around the notching levels and high amplitude beating immediately after the mode. The beating overshoots are a major risk source because they can result in the test being aborted if the qualification upper limit is exceeded. Although the abort is, in itself, a safety measure protecting the tested satellite, it increases the risk of structural fatigue, firstly because the abort threshold has been already reached, and secondly, because the test must restart at the same close-resonance frequency and remain there until the qualification level is reached and the sweep frequency can continue. The beat minimum relates only to small successive frequency ranges in which the qualification level is not reached. Although they are less problematic because they do not cause an inadvertent test shutdown, such situations inevitably result in waiver requests from the client. A controlled-system analysis indicates an operating principle that cannot provide sufficient stability: the drive calculation (which controls the process) simply multiplies the frequency reference (usually called cola) and a function of the following setpoint, the ratio between the amplitude already reached and the previous setpoint, and the compression factor. This function value changes at each cola interval, but it never takes into account the sensor signal phase. Because of these limitations, we firstly examined whether it was possible to empirically determine, using a series of tests with a very simple dummy, a controller setting process that significantly improves the results. As the attempt failed, we have performed simulations seeking an optimum adjustment by finding the Least Mean Square of the difference between the reference and response signal. The simulations showed a significant improvement during the notch beat and a small reduction in the beat amplitude. However, the small improvement in this process was not useful because it highlighted the need to change the reference at each cola interval, sometimes with instructions almost twice the qualification level. Another uncertainty regarding the consequences of such an approach involves the impact of differences between the estimated model (used in the simulation) and the actual system. As limitations in the current controller were identified in different approaches, we considered the feasibility of a new controller that takes into account an estimated single-input multi-output (SIMO) model. Its parameters were estimated from a very low-level throughput. Against this backdrop, we analyzed the feasibility of an LQG control in cancelling beating, and this article highlights the relevance of such an approach.

• Journal of Periodontal and Implant Science
• /
• v.35 no.4
• /
• pp.823-837
• /
• 2005

The purpose of this study was to study the histopathological correlation between the use of platelet-rich plasma and enamel matrix protein used in conjunction with xenograft. compared to a control group with regards to bone regeneration at the grade III furcation area in beagle dogs. Control group was treated with bovine derived bone $powder(Biocera^{(R)})$, and experimental I group was treated with bovine derived bone powder and Platelet-rich plasma and experimental II group was treated with bovine derived bone powder and Enamel matrix $protein(Emdogain^{(R)})$. The regeneration rate of bone formation was observed and compared histopathologically at 2. 4, and 8 weeks after surgery. The results were as follows: 1. In control group and both experimental groups. inflammatory cells were observed but, new bone formation wasn't. 2. In control group, new cementum on the notch was found in 4 weeks, less mature periodontal ligament when compared to that of experimental group was found and cementum formation was great but, regeneration couldn't be seen in 8 weeks. 3. Experimental I group. new bone formation in the area adjacent to alveolar bone and graft material surrounded by more dense connective tissue were found in 4 weeks. New bone formation up to crown portion was found and periodontal ligament was aligned functionally and cementum more mature. 4. Experimental II group, new bone formation was found under the defect area in 4 weeks and new bone formation around graft material in 8 weeks, too, and there were a number of fibroblasts, blood vessels, acellular cementum, which was less mature when compared to that of experimental I group, and dense collagen fiber like which normal periodontal ligament has in periodontal ligament of experimental II group in 8 weeks. 5. As a result of histologic finding, bone formation rate were 18.0${\pm}$7.87%(control group), 34. 05${pm}$7.25%(experimental I group), 19.33 ${pm}$5.15%(experimental II group) in 4 weeks and 21.89${pm}$1.58%(control group), 38.82${pm}$3.2(experimental I group), 37.65${pm}$9.22%(experimental II group) in 8 weeks. 6. Statistically significant ratio of bone formation was observed in experimental I group in 4 weeks and in experimental II group in 8 weeks. When experimental I group was compared to experimental II group, the ratio of bone formation in experimental I group was higher than that in experimental II group in 4 weeks(p<0.05). This results suggest that platelet-rich plasma showed more new bone formation than enamel matrix protein within 4 weeks. And use of enamel matrix protein in the treatment of periodontal bone defects starts to enhance regeneration after 8 weeks in beagle dogs.

• Animal Bioscience
• /
• v.36 no.7
• /
• pp.991-1002
• /
• 2023

Objective: This study aimed to elucidate the underlying gene regions responsible for productive, phenotypic or adaptive traits in different ecological types of Tibetan sheep and the discovery of important genes encoding valuable traits. Methods: We used whole-genome resequencing to explore the genetic relationships, phylogenetic tree, and population genetic structure analysis. In addition, we identified 28 representative Tibetan sheep single-nucleotide polymorphisms (SNPs) and genomic selective sweep regions with different traits in Tibetan sheep by fixation index (Fst) and the nucleotide diversity (θπ) ratio. Results: The genetic relationships analysis showed that each breed partitioned into its own clades and had close genetic relationships. We also identified many potential breed-specific selective sweep regions, including genes associated with hypoxic adaptability (MTOR, TRHDE, PDK1, PTPN9, TMTC2, SOX9, EPAS1, PDGFD, SOCS3, TGFBR3), coat color (MITF, MC1R, ERCC2, TCF25, ITCH, TYR, RALY, KIT), wool traits (COL4A2, ERC2, NOTCH2, ROCK1, FGF5, SOX9), and horn phenotypes (RXFP2). In particular, a horn-related gene, RXFP2, showed the four most significantly associated SNP loci (g. 29481646 A>G, g. 29469024 T>C, g. 29462010 C>T, g. 29461968 C>T) and haplotypes. Conclusion: This finding demonstrates the potential for genetic markers in future molecular breeding programs to improve selection for horn phenotypes. The results will facilitate the understanding of the genetic basis of production and adaptive unique traits in Chinese indigenous Tibetan sheep taxa and offer a reference for the molecular breeding of Tibetan sheep.