• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2000년도 제32회 추계학술대회 정기총회
• /
• pp.243-249
• /
• 2000

In case of the limitation of Deep RIE fabrication for Micro Gas Turbine, bearing aspect ratio is limited in very small value. The characteristics such as pressure distribution load capacity and non-linearity of a short bearing of L/D=0.083 and a conventional bearing of L/D=1.0 with coupled boundary effects are investigated far Micro Gas Tlubine bearings. The coupled efffect was analyzed by mass conservation at coupled end area. The results, increasing load capacity and non-linearity due to the coupled effect of thrust and journal bearing, are obtained and the selection of journal bearing type is discussed.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 춘계학술대회 논문집
• /
• pp.450-453
• /
• 2008

During the drawing of reentrant section like a spline, the unfilled in the corner of dies or the bended product emerges from the large reduction of area, the complex shaped sections and other nonuniform properties in material and lubrication conditions. In this study, the drawing of the spline section with the non-rotary symmetry from a circular aluminum billet has been analyzed by using commercial code DEFORM-3D. A new die construction method preventing the spline from the drawback of bending and the unfilled defect has been suggested and verified through the analysis using centroid shift method and the hybrid construction between converged and diverged profile.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.259-260
• /
• 2002

In this paper, electrical discharge machined (EDM) surfaces machined with various machining parameters are characterized and simulated. Three-dimensional surface topography of EDM surfaces are measured by a stylus instrument. Surface topography is characterized with auto-correlation coefficient and height probability density functions. Then, EDM surfaces are modeled and computer-simulated by using the non-causal 2-D auto-regressive model. Simulation results show that EDM surfaces are characterized well by a few parameters.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1999년도 제30회 추계학술대회
• /
• pp.269-275
• /
• 1999

This paper presents the results of thermoelastic wear phenomena in ventilated disk brakes for a high-speed train using finite element method. The computed results show that the sinusoidal distortions due to non-uniform distributions of temperature profiles may lead to thermoelastic wears at the rubbing surface. This may decrease the life of a disk brake and produce micro-cracks, noise and squeals between two rubbing surfaces.

• 한국표면공학회지
• /
• 제30권5호
• /
• pp.347-354
• /
• 1997

Composite plating is a method of co-depositing fine particles of metallic, non-metallic compound or polymers in the plated layer to improve material properties such as were-resistance, lubrication, or corrosion resistance. Graded Ni-Sic composite coating were produced in this research. Prior to produce Graded Ni-SiC composite coatings, effects of particle size, particle content, pH of electrolyte, temperature, current density, stirring rate on the amount of SiC deposited in the Ni layer were investigated. By manipulating current density and plating time properties of these coating were evaluated by micro-indentation hardness test.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제33회 춘계학술대회 개최
• /
• pp.327-333
• /
• 2001

DLC films due to their extreme properties have attracted a lot of attention. In this study, the films were prepared on High Speed Steel (SKH2) by microwave plasma assisted CVD method using CH4. Every friction test under the normal load 2,5N and sliding velocity of 20,25mm/s in high vacuum (5${\times}$10$\^$-5/ Torr). The films were analyzed with Raman spectroscopy. The films failed immediately in vacuum due to high friction. Wear volume of DLC coated disks decreased more than that of non-DLC coated disks. Also, hardness of the films is about 600HV.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.132-137
• /
• 2011

철도차량의 고속화, 경량화와 함께 승객의 안전성을 보다 더 높이기 위한 많은 연구가 진행 되고 있다. 철도차량의 안전성을 높이기 위해서는 주행성능을 안정시키는 것이 무엇보다 중요하며, 드라이빙기어 내부의 윤활유량을 최적화하는 것은 주행성능 확보에 필수적이다. 본 연구에서는 전동차용 Driving Gear Unit의 회전 방향에 따라 저속 Gear 치면을 통해 Splash 되는 드라이빙기어 Casing내의 윤활유 유동 변화를 ANASYS CFD 프로그램과 전산유체해석 기법을 사용하여 구현 하였으며, 해석 내역을 토대로 유사 구동 조건에 대한 무부하 실증 시험을 실시하여 해석의 적합성 및 윤활유량 선정과 드라이빙기어의 안전성에 대해 고찰하였다.

• Tribology and Lubricants
• /
• 제17권3호
• /
• pp.236-243
• /
• 2001

In this study, flow factors are evaluated in terms of kurtosis using random rough surface generated numerically. As h/$\sigma$become large ø$\sub$x/, ø$\sub$y/, ø$\sub$fp/, approach to 1 and ø$\sub$s/, ø$\sub$fs/ to 0 asymptotically regardless of kurtosis. ø$\sub$x/, ø$\sub$y/, ø$\sub$fp/ increase with increasing kurtosis in the mixed lubrication regime. ø$\sub$s/, ø$\sub$fs/ is associated with an additional flow transport due to the combined effect of sliding and roughness. As h/$\sigma$ decreases ø$\sub$s/, ø$\sub$fs/ increase up to a certain point, and then decrease toward zero. This behavior can be attributed to the increasing number of contacts in the mixed lubrication regime. ø$\sub$x/ in the presence of elastic deformation on the surface is larger than ø$\sub$x/ in the absence of it because local film thickness(h$\sub$T/) increases by elastic deformation.

• Tribology and Lubricants
• /
• 제31권4호
• /
• pp.177-182
• /
• 2015

Tapered roller bearings are widely used in equipment where high combined thrust and radial loads are experienced. A certain amount of tilting between the tapered rollers and the races always occurs because of bending moment load conditions and shaft deflection. It is now well understood that a coherent elastohydrodynamic lubrication (EHL) film separates the rollers and races. In spite of extensive study on EHL problems for over half a century, relatively few studies have focused on the finite line contacts problem. This study presents a complete numerical analysis of the effects of roller tilting on the EHL characteristics in a tapered roller bearing. We systematically analyze this highly nonlinear problem using finite differences with fully non-uniform grids and the Newton-Raphson method. Detailed EHL pressure distributions and film shapes are presented under moderate loads and material parameters. A very small roller tilting significantly affects the pressure distributions and film shapes near both ends of the roller. Moreover, the effect of tilting on the EHL characteristics at the small end is much greater than that at the large end. Therefore, in designing optimum profiles for tapered roller bearings, the profile radius should be larger at the small end.

• 비파괴검사학회지
• /
• 제30권2호
• /
• pp.121-125
• /
• 2010

회전기기의 결함진단에 있어서 기존의 방법과 달리 적외선열화상기술은 회전기기의 결함진단에 대해 비접촉, 비파괴 및 상태감시 모니터링을 할 수 있다. 본 논문에서는 적외선열화상 상태진단을 기반으로 하는 회전기기의 결함진단에 대한 새로운 접근법을 제안한다. 따라서 회전기에서 가장 많이 사용되어지는 볼베어링을 이용하여 실험을 수행하였고, 진동 스펙트럼 분석과 적외선열화상을 이용하여 실시간 모니터링을 수행하였다. 적외선열화상기법을 이용하여 볼베어링의 윤활 불균형에 따른 온도 특성을 확인할 수 있었다. 이러한 실험을 통한 결과를 분석 검토하여 향후 산업전반의 회전기기의 상태감시연구에 있어서 다양한 분야에 사용되어 질 것으로 예상된다.