• 대한기계학회논문집A
• /
• 제34권9호
• /
• pp.1137-1143
• /
• 2010

가스용접 구조물의 장 수명 피로설계기준(fatigue design criterion)을 결정하기 위해서는 정확한 응력해석과 체계적인 피로강도평가가 필요하다. 그러나 실 구조물로부터 피로설계기준을 결정하는 것은 대단히 어려우므로 구조물의 기계적 구조적 특성을 만족하는 간편 시편을 만들어서 $\Delta{\sigma}-N_f$ 관계를 도출하여 피로강도를 평가하고 있다. 그리고 가스용접에 의해 제작된 실 구조물의 피로설계를 위해서는 피로균열발생과 파단 기점이 되는 용접부의 용접잔류응력(welding residual stress)이 고려되어야 한다. 따라서, 본 연구에서는 플러그 및 링 가스용접 이음재에 대한 용접잔류응력을 고려하기 위해 용접 열 사이클(heat cycle)에 의한 비선형 열해석(non-linear thermal analysis)과 열 응력(thermal stress) 해석을 수행하고, 실험 치와 비교 분석하여 용접잔류응력을 고려한 응력 진폭-피로수명($(\sigma_a)_R-N_f$) 관계를 도출하여 자동적으로 피로설계기준을 제시할 수 있도록 하고자 하였다.

• 대한조선학회논문집
• /
• 제44권1호
• /
• pp.32-39
• /
• 2007

A three-dimensional finite element model has been developed to simulate the MIG P/S welding process of two aluminum plates. The finite element calculations are performed using ANSYS finite element code, which takes into account the thermal and mechanical non-linear material properties. The results of finite element analysis compared with those of experiment to show its validity in view of distortions. Parametric studies are carried out on the validated model to assess the effects of various factors on the final residual distortion. Large deformations, temperature dependent material properties are included in the model. Finally, the formulas of fitting curves of angular distortion transverse shrinkage, and longitudinal shrinkage have been proposed.

• International Journal of Korean Welding Society
• /
• 제5권1호
• /
• pp.15-28
• /
• 2005

The ball shear test was investigated in terms of the effects of test parameters, i.e., shear height and shear speed, with an experimental and non-linear finite element analysis for evaluating the solder joint integrity of area array packages. Two representative Pb-free solder compositions were examined in this work: Sn-3.5Ag-0.75Cu and In-48Sn. The substrate was a common SMD type with solder bond pad openings of 460 $\mu$m in diameter. The microstructural investigations were carried out using SEM, and the IMCs were identified with EDS. Shear tests were conducted with the two varying test parameters. It could be observed that increasing shear height, at fixed shear speed, has the effect of decreasing shear force for both Sn-3.5Ag-0.75Cu and In-48Sn solder joints, while the shear force increased with increasing shear speed at fixed shear height. Too high shear height could cause some undesirable effects on the test results such as unexpected high standard deviation values or shear tip sliding from the solder ball. The low shear height conditions were favorable for screening the type of brittle interfacial fractures or the degraded layers in the interfaces. The shear speed conditions were discussed with the stress analyses of the solder ball, and we cannot find any conspicuous finding which is related to optimum shear speed from the stress analyses.

• Journal of Welding and Joining
• /
• 제31권3호
• /
• pp.76-83
• /
• 2013

This study investigated the effect of bonding temperature and holding time on microstructures and mechanical properties of diffusion bonded joint of Haynes230. The diffusion bonds were performed at the temperature of 950, 1050, and $1150^{\circ}C$ for holding times of 30, 60, 120 and 240 minutes at a pressure of 4MPa under high vacuum condition. The amount of non-bonded area and void observed in the bonded interface decreased with increasing bonding temperature and holding time. Cr-rich precipitates at the linear interface region restrained grain migration at $950^{\circ}C$ and $1050^{\circ}C$. However, the grain migration was observed in spite of short holding time due to the dissolution of precipitates to base metal in the interface region at $1150^{\circ}C$. Three types of the fracture surface were observed after tensile test. The region where the coalesce and migration of grain occurred much showed high fracture load because of base metal fracture whereas the region where those did less due to the precipitates demonstrated low fracture load because of interface fracture. The expected fracture load could be derived with the value of fracture area of base metal ($A_{BF}$) and interface ($A_{IF}$), $Load=201A_{BF}+153A_{IF}$. Based on this equation, strength of base metal and interface fracture were calculated as 201MPa and 153MPa, respectively.

• Structural Engineering and Mechanics
• /
• 제70권4호
• /
• pp.431-443
• /
• 2019

The present paper illustrates a numerical investigation on the failure behaviour of ring-stiffened cylinder subjected to external hydrostatic pressure. The published test data of steel welded ring-stiffened cylinder are surveyed and collected. Eight test models are chosen for the verification of the modelling and FE analyses procedures. The imperfection as the consequences of the fabrication processes, such as initial geometric deformation and residual stresses due to welding and cold forming, which reduced the ultimate strength, are simulated. The results show that the collapse pressure and failure mode predicted by the nonlinear FE analyses agree acceptably with the experimental results. In addition, the failure mode parameter obtained from the characteristic pressure such as interframe buckling pressure known as local buckling pressure, overall buckling pressure, and yield pressure are also examined through the collected data and shows a good correlation. A parametric study is then conducted to confirm the failure progression as the basic parameters such as the shell radius, thickness, overall length of the compartment, and stiffener spacing are varied.

• Computers and Concrete
• /
• 제22권1호
• /
• pp.27-37
• /
• 2018

Reinforced concrete structures are widely used in civil engineering projects around the world in different designs. Due to the great evolution in computational equipment and numerical methods, structural analysis has become more and more reliable, and in turn more closely approximates reality. Thus among the many numerical methods used to carry out these types of analyses, the finite element method has been highlighted as an optimized tool option, combined with the non-linear and linear analysis techniques of structures. In this paper, the behavior of reinforced concrete beams was analyzed in two different configurations: i) with welding and ii) conventionally lashed stirrups using annealed wire. The structures were subjected to normal and tangential forces up to the limit of their bending resistance capacities to observe the cracking process and growth of the concrete structure. This study was undertaken to evaluate the effectiveness of welded wire fabric as shear reinforcement in concrete prismatic beams under static loading conditions. Experimental analysis was carried out in order compare the maximum load of both configurations, the experimental load-time profile applied in the first configuration was used to reproduce the same loading conditions in the numerical simulations. Thus, comparisons between the numerical and experimental results of the welded frame beam show that the proposed model can estimate the concrete strength and failure behavior accurately.

• 대한토목학회논문집
• /
• 제32권3A호
• /
• pp.149-160
• /
• 2012

파형강판은 보강재 없이 높은 전단 저항력을 가지며, 보강재를 생략함으로써 상부구조의 용접을 최소화하고 피로 성능을 향상시킨다. 이러한 장점으로 인하여 최근에 파형강판을 I-거더의 복부판으로 사용하려는 연구가 여러 연구자들에 의하여 수행되었다. 횡-비틂 좌굴은 I-거더를 설계함에 있어 주요한 설계인자이지만 불균일 모멘트와 같은 실제 하중이 작용하는 파형강판 I-거더의 횡-비틂 좌굴에 관한 연구는 현재 미흡한 실정이므로 이에 대한 연구가 필요하다. 본 연구에서는 파형강판 I-거더의 횡-비틂 좌굴 강도에 관한 연구를 수행하였다. 먼저 선형 모멘트 구배가 작용하는 파형강판 I-거더의 탄성 횡-비틂좌굴 거동에 관한 연구를 유한요소해석을 통하여 수행하였다. 본 연구 결과, 파형강판 I-거의 탄성 횡-비틂 좌굴 거동은 파형강판의 파형 주기수에 따라 달라지는 것을 알 수 있었으며, 선형 모멘트 구배가 작용하는 파형강판 I-거더에 대한 모멘트 구배 수정 계수를 제안하였다. 이 후 비탄성 유한요소해석 결과와 일반 I-거더의 설계 방법을 이용하여 파형강판 I-거더의 비탄성 좌굴 강도에 관하여 연구를 수행하였다.

• 해양환경안전학회지
• /
• 제29권5호
• /
• pp.488-496
• /
• 2023

선박 및 교량 구조물은 일종의 길이가 긴 박스형 구조로서 수직 굽힘 모멘트에 대한 저항력이 설계의 주요 인자이다. 특히 선박 거더는 반복적으로 불규칙적인 파랑하중에 장시간 노출되어 있기 때문에 구조부재의 연속 붕괴 거동을 정확하게 예측하는 것이 무엇보다도 중요하다. 본 논문에서는 순수 휨모멘트를 받는 박스거더의 하중 변화에 따른 좌굴을 포함한 소성 붕괴 거동을 수치해석적 방법을 이용하여 분석하였다. 분석대상은 Gordo 실험에서 사용한 세 가지 박스거더로 선정하였다. 구조강도 실험 결과와 비선형 유한요소해석에 의한 결과를 비교하여 차이가 발생하는 원인에 대해서 고찰하였다. 본 논문에서는 카본스틸 재료의 제작 시 필연적으로 사용하는 용접열에 의한 초기 처짐의 영향을 반영하기 위하여 전체와 국부적인 처짐 형상의 조합을 제안하였고, 이 결과는 실험 결과와 거동 및 최종강도 추정율이 7% 이내에서 잘 일치하고 있었다. 논문에서 검토한 절차 및 초기 처짐 구성에 대한 내용은 향후 유사 구조물의 최종강도를 분석하는데 좋은 지침으로 사용할 수 있다.