• Structural Engineering and Mechanics
• /
• 제64권5호
• /
• pp.543-555
• /
• 2017

The non-linear behaviour of integral infilled frames (in which the infill and the frame are bonded together with help of various interface materials) is studied both experimentally and numerically. The experiments were carried out on one-sixth scale two-bay and three-storey reinforced concrete frames with and without infill against static cyclic loading. Three interface materials - cement mortar, cork and foam have been used in between the infill and the frame. The infill, interface and the frame are bonded together is called integral frame. The linear and non-linear behaviors of two dimensional bare frame and integral infilled frame have been studied numerically using the commercial finite element software SAP 2000. Linear finite element analysis has been carried out to quantify the effect of various interface materials on the infilled frames with various combinations of 21 cases and the results compared. The modified configuration that used all three interface materials offered better resistance above others. Therefore, the experiments were limited to this modified infilled frame case configuration, in addition to conventional (A1-integral infilled frame with cement mortar as interface) and bare frame (A0-No infill). The results have been compared with the numerical results done initially. It is found that stiffness of bare frame increased by infilling and the strength of modified frame increased by 20% compare to bare frame. The ductility ratio of modified infilled frame was 42% more than that of the conventional infilled frame. In general, the numerical result was found to be in good agreement with experimental results for initial crack load, ultimate load and deformed pattern of infill.

• 한국건설순환자원학회논문집
• /
• 제4권4호
• /
• pp.425-430
• /
• 2016

산업의 급격한 발달과 함께 사회 또한 급격한 발달을 이루면서 전 세계는 편리한 생활을 이룰 수 있게 되었다. 하지만 이러한 산업의 발달의 이면에는 환경오염으로 인한 지구온난화와 산업부산물 대량 발생 등의 문제가 발생하고 있는 실정이다. 이에 본 연구는 건축분야에서 $CO_2$ 배출 비율이 높은 시멘트의 사용량을 줄이고자 산업부산물인 고로슬래그와 순환 유동층 연소 플라이애시를 사용하였으며, 국내 염색공단에서 배출되고 있는 20만 톤 이상의 슬러지를 재활용하는 방안을 검토하기 위해 염색슬러지 탄화물을 활용한 무시멘트 경화체의 특성에 대한 기초자료를 제시하고자 하였다. 그 결과, 염색슬러지 탄화물의 치환율이 증가함에 따라 공기량은 증가하였고 플로어는 증가하였다. 또한 염색슬러지 탄화물 치환율이 증가함에 따라 휨강도 및 압축강도는 감소하는 경향을 보였다.

• 터널과지하공간
• /
• 제10권2호
• /
• pp.180-195
• /
• 2000

본 연구에서는 주입에 의한 암석절리면의 수직압축특성과 전단특성의 변화를 규명하기 위하여 신선한 인공절리에 대하여 시멘트현탁액을 주입한 후, 절리 압축시험과 직접전단시험을 실시하였다. 시멘트현탁액을 주입한 맞물린 단일암석 절리의 수직압축시험결과, 주입전 비선형적이었던 절리의 수직응력-수직변형곡선은 선형적으로 바뀌었으며 2 MPa까지의 수직변형은 주입전의 1/10정도로 감소하였다. 시멘트현탁액 주입후 신선한 단일암석절리에 대한 직접전단시험결과, 파괴포락선은 1 MPa내외의 점착력과주입전보다 낮은 마찰각을 가지는 것으로 나타났으며, 주입두께가 커질수록 마찰각은 더 낮아지는 것으로 나타났다. 잔류전단강도는 주입두에와의 상관성을 확인할 수 없었으나, 전단강성과 최대팽창각은 주입두께가 증가할수록 감소하는 경향을 나타내었다. 이러한 주입두께에 대한 전단특성들의 감소현상들은 주입재에 의한 절리면 유효거칠기의 감소효과로부터 발생한 것으로 판단되며 직접전단시험에서 얻어진 최대전단강도를 주입두께대 거칠기평균진폭비를 포함한 경험식으로 나타내었다.

• 한국산학기술학회논문지
• /
• 제21권9호
• /
• pp.405-413
• /
• 2020

압축 유동하에서 측정된 시멘트 페이스트의 수직 응력은 변형률의 증가에 따라 변형률이 0.0003에서 0.003 사이 구간인 탄성 고체 구간과 변형률이 0.003에서 0.8 사이 구간인 변형률 경화 구간으로 나누어진다. 두 구간 중 변형률 경화 영역에서 유변학적 특성을 분석하기 위해 모델링 식이 제안되었다. 첫째, 유체 거동의 관점에서, 지수법칙 일관성 지수 m=700 및 멱지수 n=0.2를 갖는 지수법칙 비뉴토니언 모델이 적용되었다. 적용 결과는 탄성 고체 구간을 제외하고는 실험 결과와 좋은 일치를 보여주었다. 둘째, 연성 고체 거동의 관점에서 힘 평형 모델이 적용되었으며, 하중을 측정하는 센서부와 시멘트 페이스트 표면 간의 마찰 계수가 실험데이터에 반구간탐색법을 적용하여 변형률의 다항식으로 도출되었다. 적용 결과는 변형률이 0.003에서 0.3 사이 구간인 중간 영역에서만 실험 결과와 좋은 일치를 보여주었다. 따라서, 압축 유동 하의 시멘트 페이스트의 유변학적 거동은 변형률 경화 구간에서 연성 고체 거동의 관점보다는 지수법칙 비뉴토니언 유체 거동의 관점에서 실험 결과와 더 일치함을 보여주었다.

• 대한치과보철학회지
• /
• 제17권1호
• /
• pp.23-34
• /
• 1979

In this study, the adhesive strength of three commercial polycarboxylate cements to ten types of dental casting alloys, such as gold, palladium, silver, indium, copper, nickel, chromium, and human enamel and dentine were measured and compared with that of a conventional zinc phosphate cement. The $8.0mm{\times}3.0mm$ cylindrical alloy specimens were made by casting. The enamel specimens were prepared from the labial surface of human upper incisor, and the dentine specimens were prepared from the occulusal surface of the human molar respectively. Sound extracted human teeth, which had been kept in a fresh condition since, extraction, were mounted in a wax box with a cold-curing acrylic resin to expose the flattened area. The mounted teeth were then placed in a Specimen Cutter (Technicut) and were cut down under a water spray, and then the flat area on the all specimens were ground by hand with 400 and 600 grit wet silicone carbide paper. Two such specimens were then cemented together face-to-face with freshly mixed cement, and moderate finger pressure was applied to squeeze the cement to a thin and uniform film. All cemented specimens were then kept in a thermostatic humidor cabinet regulated at $23{\pm}2^{\circ}C.$ and more than 95 per cent relative humidity and tested after 24 hours and 1 week. Link chain was attached to each alloy specimen to reduce the rigidity of the jig assembly, and then all the specimens were mounted in the grips of the Instron Universal Testing Machine, and a tensile load was delivered to the adhering surface at a cross head speed of 0.20 mm/min. The loads to which the specimens were subjected were recorded on a chart moving at 0.50 mm/min. The adhesive strength was determined by measuring the load when the specimen separated from the cement block and by dividing the load by the area. The test was performed in a room at $23{\pm}2^{\circ}C.$ and $50{\pm}10$ per cent relative humidity. A minimum of five specimens were tested each material and those which deviated more than 15 per cent from the mean were discarded and new specimens prepared. From the experiments, the following results were obtained. 1) It was found that the adhesive strength of the polycarboxylate cement to all alloys tested was considerably greater than that of the zinc phosphate cement. 2) The adhesive strength of the polycarboxylate cements was superior to the non precious alloys, such as the copper, indium, nickel and chromium alloys, but it was inferior to the precious gold, silver and palladium alloys. 3) Surface treatment of the alloy was found to be an important factor in achieving adhesion. It appears that a polycarboxylate cement will adhere better to a smooth surface than to a rough one. This contrasts with zinc phosphate cements, where a rough helps mechanical interlocking. 4) The adhesion of the polycarboxylate cement with enamel was found superior to its adhesion with dentine.

• Restorative Dentistry and Endodontics
• /
• 제24권1호
• /
• pp.136-146
• /
• 1999

The purpose of this study was to estimate the changes of marginal adaptation to the cavity floor of light-cured glass ionomer cement base after application of a composite restoration. Eighty non-carious extracted human molars were used in the present study. Circular cavities were prepared on the center of the exposed dentin surface to 0.5mm, 1.0mm, 1.5mm, 2.0mm in depth and the prepared cavities were pretreated with Dentin conditioner and filled with Fuji II LC(GC Int. Co., Japan). They randomly assigned into 3 groups according to the difference in application of a composite restoration; Group 1(control group): only glass ionomer base, Group 2: The application of a composite restoration surrounded by dentin with class I cavity over glass ionomer base after conventional dentin bonding to the exposed dentin and glass ionomer base, Group 3: The application of composite restoration not-surrounded by dentin over glass ionomer base after conventional dentin bonding to the exposed dentin and glass ionomer base. To examine the interface between cavity floor and light-cured glass ionomer cement base, each groups were sectioned vertically through the center of restorations with diamond saw and the gap size(${\mu}m$) of interface measured by SEM. The results were analyzed by using One Way ANOVA. The results were as follows: 1. Good adaptation between glass ionomer cement base and cavity floor was showed in specimens with 0.5mm, 1.0mm depth base of control group. But in specimens with 1.5mm, 2.0mm depth base of control group, the gap was measured about $15{\mu}m$, $40{\mu}m$ respectively. 2. Gap size in group 2 was significantly higher than that in control group(P<0.05). 3. Gap size in group 3 was significantly higher than that in control group and group 2(P<0.05). 4. It was possible to observe the good adaptation between glass ionomer cement base and dentin which was intermediated with 4-10${\mu}m$ hybrid layer in specimens with 0.5mm, 1.0mm depth base of control group. Cohesive fracture within cement base was observed in all specimens which had the gap between glass ionomer cement base & dentin. 5. It was possible to observe the gap formation between cement base and bonding agent and between composite resin and dentin in all specimens of group 2.

• 한국농공학회논문집
• /
• 제47권5호
• /
• pp.27-39
• /
• 2005

In the recent design of high ductile fiber-reinforced ECC (engineered cementitious composite), optimizing both processing and mechanical properties for specific applications is critical. This study presents an innovative method to develop new class ECCs, which possess the different fluid properties to facilitate diverse types of processing (i.e., self-consolidating or shotcrete processing) while maintaining ductile hardened properties. In the material design concept, we employ a parallel control of fresh and hardened properties by using micromechanics and cement rheology. Control of colloidal interaction between the particles is regarded as a key factor to allow the performance of the specific processing. To determine how to control the particle interactions and the viscosity of cement suspension, we first introduce two chemical admixtures including a highly charged polyelectrolyte and a non-ionic polymer. Optimized mixing steps and dosages we, then, obtained within the solid concentration predetermined based on micromechanical principle. Test results indicate that the rheological properties altered by this approach were revealed to be highly effective in obtaining the desired function of the fresh ECC, allowing us to readily achieve hardened properties, represented by pseudo strain-hardening behavior in uniaxial tension.

• Advances in concrete construction
• /
• 제9권5호
• /
• pp.469-478
• /
• 2020

This study aims to establish a new methodological framework for the evaluation of the evolution of the reliability of plain concrete for pavement vs number of cycles under flexural fatigue loading. According to the framework, a new method calculating the reliability was proposed through probability simulation in order to describe a random accumulation of fatigue damage, which combines reliability theory, one-to-one probability density functions transformation technique, cumulative fatigue damage theory and Weibull distribution theory. Then the statistical analysis of flexural fatigue performance of cement concrete tested was carried out utilizing Weibull distribution. Ultimately, the reliability for the tested cement concrete was obtained by the proposed method. Results indicate that the stochastic evolution behavior of concrete materials under fatigue loading can be captured by the established framework. The flexural fatigue life data of concrete at different stress levels is well described utilizing the two-parameter Weibull distribution. The evolution of reliability for concrete materials tested in this study develops by three stages and may corresponds to develop stages of cracking. The proposed method may also be available for the analysis of degradation behaviors under non-fatigue conditions.

• 방사선산업학회지
• /
• 제8권1호
• /
• pp.53-57
• /
• 2014

The kenaf is quickly developing as a renewable resource. Kenaf can be grown under a wide range of weather conditions. Modification of kenaf fiber by graft polymerization provides a significant route to alter the chemical properties, including surface hydrophilicity or hydrophobicity. In this study, kenaf fiber surfaces were grafted with acrylic acid as a hydrophilic group using electron beam irradiation. The grafting rate increased with an increase in grafting time. The FT-IR results confirmed that acrylic acid was successfully grafted onto the kenaf fibers. The wettability of the kenaf fiber was increased, accompanied by acylic acid grafting on the fiber surface. According to the permeability test result, it was found that acrylic acid grafted kenaf fiber reinforced cement composite was more reduced than non-grafted kenaf fiber reinforced cement composite.

• Elastomers and Composites
• /
• 제35권3호
• /
• pp.196-204
• /
• 2000

방수제로 사용하는 EVA 에멀젼 수지에 라텍스 형태의 아크릴 수지, 에폭시 수지, 우레탄 수지, SBR 수지를 전체 혼합물 중에 $0{\sim}50%$ 혼합하여 소포성, 기계적 물성, 내수성 등을 조사하였다. 소포제의 소포효과는 BYK-021이 가장 우수하였으며 적절한 사용량은 전체 혼합물에 대하여 0.3phr이었다. 수축율은 수지간의 상용성과 기공형성도에 영향을 받았으며 기계적 강도는 수지 분자간의 응집력, 수지와 시멘트의 결합력, 시멘트 입자간의 응집력 등에 영향을 받았다. 라텍스를 혼합한 것은 혼합하지 않은 것보다 수축율, 굴곡강도, 접착강도, 충격강도 등에서 우수한 물성을 나타내었다. EVA에 시멘트를 혼합했을 때에는 혼합하지 않았을 때보다 내수성이 떨어졌다.