• 대한치과기공학회지
• /
• 제14권1호
• /
• pp.55-65
• /
• 1992

The purpose of this study was to investigate the comparison of physical properties of nonprecious metal alloys colored goldish yellow. The experimental groups were copper based dental alloy and control group was Ni-Cr based dental alloy used crown and bridges frameworks. Hardness was tested by vickers hardness tester, tensile strength was tested by universal tension tester. After testing the tensile strength of castings, the microstrucure and the pattern of fracture were investigated by scanning electron microscope and metallurgical microscope. The results were as follows : Hardness of Ni based alloy was higher than Cu based alloys. Hardness number of A group was 200.41$\pm$16.10 Hv, B group was 194.33$\pm$1.69 Hv, C group was 139.29$\pm$2.19 Hv and D group was 293.81$\pm$27.17 Hv, respectively. Tensile strength of D group was 56.42$\pm$6.17 $kg/m^2$, A group was 50.39$\pm$5.68 $kg/m^2$, C group was 45.13$\pm$4.53 $kg/m^2$, B group was 45.25$\pm$9.25 $kg/m^2$, in order, and D group was maximum tensile strength. The fractured surfaces of tensile specimens in the all groups showed the tendency to form large voids in the center of specimens. Thus the ductile fracture was changed into the brittle fracture with the fine grain size.

• Geomechanics and Engineering
• /
• 제15권4호
• /
• pp.927-935
• /
• 2018

The mechanical behavior of the brittle material samples containing the internal and edge cracks are studied under direct shear tests. It is tried to investigate the effects of stress interactions and stress intensity factors at the tips of the pre-existing cracks on the failure mechanism of the bridge areas within these cracks. The direct shear tests are carried out on more than 30 various modeled samples each containing the internal cracks (S models) and edge cracks (E models). The visual inspection and a low power microscope are used to monitor the failure mechanisms of the tested samples. The cracks initiation, propagation and coalescences are being visualized in each test and the detected failure surfaces are used to study and measure the characteristics of each surface. These investigations show that as the ratio of the crack area to the total shear surface increases the shear failure mode changes to that of the tensile. When the bridge areas are fixed, the bridge areas in between the edge cracks have less strength than those of internal cracks. However, the results of this study show that for the case of internal cracks as the bridge area is increased, the strength of the material within the bridge area is decreased. It has been shown that the failure mechanism and fracture pattern of the samples depend on the bridge areas because as the bridge area decreases the interactions between the crack tip stress fields increases.

• Steel and Composite Structures
• /
• 제1권1호
• /
• pp.145-158
• /
• 2001

An experimental study was conducted to evaluate the effects of loading sequence and lateral bracing on the behavior of reduced beam section (RBS) steel moment frame connections. Four full-scale moment connections were cyclically tested-two with a standard loading history and the other two with a near-fault loading history. All specimens reached at least 0.03 radian of plastic rotation without brittle fracture of the beam flange groove welds. Two specimens tested with the nearfault loading protocol reached at least 0.05 radian of plastic rotation, and both experienced smaller buckling amplitudes at comparable drift levels. Energy dissipation capacities were insensitive to the types of loading protocol used. Adding a lateral bracing near the RBS region produced a higher plastic rotation; the strength degradation and buckling amplitude were reduced. A non-linear finite element analysis of a one-and-a-half-bay beam-column subassembly was also conducted to study the system restraint effect. The study showed that the axial restraint of the beam could significantly reduce the strength degradation and buckling amplitude at higher deformation levels.

• 한국지진공학회논문집
• /
• 제22권1호
• /
• pp.23-32
• /
• 2018

In this study, we conducted a shake table test to verify the seismic performance of the paneling system with steel truss composed of bolt connections. The control group was set to the traditional paneling system with steel truss connected by spot welding method. Test results showed that the bolted connection type paneling system has excellent deformation capacity without cracking or brittle fracture of the steel truss connection parts compared to the welding type paneling system. Furthermore, in the bolted connection type, slight damage occurred at the time of occurrence of the same story drift angle as compared with the existing method, it is considered that it has excellent seismic performance. In compliance with the performance-based design recommended for the current code (ASCE 41-13) on non-structural components, it is judged that in the case of the bolted connection type paneling system, it can be applied to all risk category structures without restriction. However, in the case of traditional paneling system with spot welding method, it is considered that it can be applied limitedly.

• 한국해양공학회지
• /
• 제17권3호
• /
• pp.46-51
• /
• 2003

Acoustic emission (AE) signals, emanated during local failure of aluminum alloys, have been the subject of numerous investigations. It is well known that the characteristics of AE are strongly influenced by the previous thermal and mechanical treatment of the sample. Possible sources of AE during deformation have been suggested as the avalanche motion of dislocations, fracture of brittle particles, and debonding of these particles from the alloy matrix. The goal of the present study is to determine if AE occurring as the result of fatigue crack propagation could be evaluated by the joint time-frequency analysis method, short time Fourier transform (STFT), and Wigner-Ville distribution (WVD). The time-frequency analysis methods can be used to analyze non-stationary AE more effectively than conventional techniques. STFT is more effective than WVD in analyzing AE signals. Noise and frequency characteristics of crack openings and closures could be separated using STFT. The influence of various fatigue parameters on the frequency characteristics of AE signals was investigated.

• 대한조선학회논문집
• /
• 제28권2호
• /
• pp.228-240
• /
• 1991

균열진전에 관한 많은 실험결과는 피로 균열진전 과정이 확률과정(stochastic process)임을 보여주고 있다. 따라서, 피로 균열진전에 관한 연구는 확률론적 기반에서 다루어져야 한다. 본 연구에서는 균열의 진전과정을 discrete Markov process로 가정하여, Bogdanoff가 제안한 Markov chain model(MCM)을 이용하여 구조물의 신뢰도를 평가할 수 있는 방법을 제시한다. 본 연구에서는 구조부재의 파괴형태로 누출, 소성붕괴 그리고 취성파괴를 취하였으며, 초기 균열크기의 변동성, 검사의 효과 등이 고려되었다. 또한, 불규칙 하중은 등가음력의 개념을 도입하여 처리하였다. 그리고, 구조물에의 계산례를 통하여 본 연구의 유용성을 보였다.

• 한국재료학회지
• /
• 제27권12호
• /
• pp.643-651
• /
• 2017

Four types of high Mn TWIP(Twinning Induced Plasticity) steels were fabricated by varying the Mn and Al content, and the tensile properties were measured at various strain rates and temperatures. An examination of the tensile properties at room temperature revealed an increase in strength with increasing strain rate because mobile dislocations interacted rapidly with the dislocations in localized regions, whereas elongation and the number of serrations decreased. The strength decreased with increasing temperature, whereas the elongation increased. A martensitic transformation occurred in the 18Mn, 22Mn and 18Mn1.6Al steels tested at $-196^{\circ}C$ due to a decrease in the stacking fault energies with decreasing temperature. An examination of the tensile properties at $-196^{\circ}C$ showed that the strength of the non-Al added high Mn TWIP steels was high, whereas the elongation was low because of the martensitic transformation and brittle fracture mode. Although a martensitic transformation did not occur in the 18Mn1.9Al steel, the strength increased with decreasing temperature because many twins formed in the early stages of the tensile test and interacted rapidly with the dislocations.

• 한국강구조학회 논문집
• /
• 제26권5호
• /
• pp.385-396
• /
• 2014

1994년 미국 노스리지 지진 당시 상당 부분의 피해가 보 하부 플랜지에서 발생하였는데, 이의 원인으로 여러 가지가 거론되었지만 바닥슬래브와 합성작용에 의한 중립축 상승이 주요한 역학적 원인으로 인정되고 있다. 국내의 경우 지진에 저항하는 모멘트골조에 속하는 보(moment frame beam)의 경우에 순철골보로서 설계하고도 실제 시공시에는 보 상부 플랜지에 전단스터드를 필요 이상으로 과도하게 배치하는 오랜 관행이 존재하고 있어 내진성능 확보 차원에서 문제를 유발할 소지가 있다. 본 논문에서는 의도하지 않은 또는 과도한 합성작용이 내진성능에 미치는 부작용을 실물대 실험을 통해 재현하고 이의 개선방향을 모색하고자 하였다. 국내 관행에 따른 접합상세와 합성바닥구조를 갖는 실험체(PN700-C)의 경우, 합성도가 23% 정도임에도 불구하고, 상부플랜지 압축응력에 대해 중립축이 현저히 상승하였고 결국 3% 층간변위에서 콘크리트 압괴를 수반하면서 하부플랜지 취성파단이 발생하였다. 반면 합성바닥이 포함되어 있으나 합성작용이 최소화되도록 설계된 RBS접합부실험체(DB700-C)는 순철골(비합성) RBS접합부실험체(DB700-NC)와 유사한 이력거동을 보이면서 어떤 취성파괴도 없이 5% 수준의 뛰어난 층간변형 능력을 발휘하였다. 본 연구결과는 강구조접합부의 내진보강이나 신축에 있어 모멘트골조에 속한 철골보 및 접합부는 바닥구조와의 합성작용이 최소화되도록 설계 및 시공되어야 함을 시사한다.

• 비파괴검사학회지
• /
• 제27권2호
• /
• pp.97-104
• /
• 2007

SPPH강의 응력부식 균열과 용접 결함의 AE 신호의 특성을 살펴보았다. 고압배관 용접부의 결함 진전을 유도하기 위하여 부식용액(NaOH)과 국부가열 후 급랭 등의 기법을 적용하여 시험체를 제작하였다. AE 신호분석 결과, 결함으로 의심되는 영역에서 발생되는 AE 신호의 진폭은 $60{\sim}75\;dB$로 나타났으며 누적 진폭 분포 특성 조사에서 용접결함만이 존재하는 시험체는 0.034, 0.034, 0.035의 기울기를 나타내며 부식을 가한 시험체는 용접결함 기구와 부식기구가 합해져 새로운 기울기인 0.040, 0.039, 0.041로 그 차이는 적으나 기울기의 증가가 확인되었다. 가압 3분 이후 각 구간에서 응력부식결함에 의한 AE신호의 검출이 용이하였고 본 실험을 통하여 급작스런 취성파괴를 일으키는 특성을 가지고 있는 응력부식균열(SCC)의 발생 예측과 피해 예방이 가능함을 알 수 있었다.

• 한국재료학회지
• /
• 제6권8호
• /
• pp.841-851
• /
• 1996

최근의 연구에 의하면 직접 소입강에서 미량의 베이나이트상의 생성이 확인되었다. 마르텐사이트 변태전에 생성된 베이나이트상은 마르텐사이트의 패킷을 미세화시키고 입도 미세화로 기계적 성질을 향상시킨다고 한다. 본 연구에서는 미량 합금 원소로 Mo, B 등을 첨가한 강을 $1200^{\circ}C$에서 단조하여 물에 직접 소입한 후, 베이나이트상의 분율을 조절하기 위해 베이나이트 변태 온도에서 일정시간 유지하는 열처리 과정을 거쳐 생성된 베이나이트상의 분율과 기계적 성질간의 관계를 고찰하였다. 이로써 마르텐사이트와 베이나이트 혼합 조직의 강도와 인성을 증가시키는 효과적인 베이나이트 분율을 조사한 후에, 직접 소입시에 이와 같은 분율의 베이나이트 함량으로 조절할 수 있는 방법을 제시하여 고강도 고인성형 직접 소입강의 개발에 활용하고자 한다.