• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 추계학술대회논문집
• /
• pp.125-131
• /
• 2000

The turbo chiller uses centrifugal compressor, which operates at about 14500 rpm. Due to the high rpm of the impeller, the noise of chiller makes one of the serious problems. The possibility of the sound reduction by using absorbing material is studied in this paper. The generated sound propagates through the duct and then radiates to the outer field. So, the use of sound absorption material inside the duct is one of the effective methods. To study the effect of location of the material, we use Boundary Element Method to analyze the sound field inside the duct system. Numerical study shows the highest sound pressure region is near the elbow of curved duct. From the analysis, it is also shown that the elbow duct is the main radiator of noise and sound absorption treatment of this duct results noise reduction of the highest noise level at BPF and high frequency region.

• Journal of the Korean Wood Science and Technology
• /
• 제46권4호
• /
• pp.362-367
• /
• 2018

This study estimates the sound absorption capability of rice straw particle mats by two methods: the transfer function method and the reverberation room method. In the reverberation method, the central frequency was set to the one-third octave band in the 100-5000 Hz range; in the transfer function method, the frequency range was 500-6400 Hz. Both methods yielded similar noise reduction coefficients of the rice straw mats. The noise reduction coefficient was approximately 0.8, indicating a high sound-absorption property of the mats. Therefore, rice straw matting is a suitable candidate material for sound-barrier walls against highway noise.

• 한국소음진동공학회논문집
• /
• 제16권9호
• /
• pp.964-970
• /
• 2006

Micro gas turbine(MGT) has received attention recently as small-scale distributed power sources. With characteristics such as their small size, lightweight, low maintenance cost and minimal vibrations during operation, they are expected to become widespread in a wide range of ' applications, including residential and small-scale industrial use. It is very easier to start-up and stop the MGT system which is the friendly environmental power system has just below the 9ppm NOx emmission and good quality of noise level. The exhaust heat emitted by the MGT is in the form of about $300^{\circ}C$ clean exhaust gas. The exhaust gas is suitable for absorption chiller/heater system. 1 has researched performance characteristics of the 60 kW class MGT-absorption chiller-heater system in the local condition. Variations of heat recovery from exhaust gas has measured according to micro gas turbine output of 15, 30, 45, 60kW. From those results, the performance of the MGT-absorption chiller/heater system has been evaluated.

• 한국소음진동공학회논문집
• /
• 제22권2호
• /
• pp.103-114
• /
• 2012

Nowadays membrane material is widely used for large indoor spaces and long spaces such as traditional market. Thermal insulation and sound field control performance is considered as a main properties for design of such buildings. In this paper sound absorption and thermal insulation properties of membrane material was investigated. Firstly, normal incidence sound absorption coefficient of 10 kinds of glass wool textiles showed that sound absorption coefficient was increased in proportion of thickness and surface density of textile. Sound absorption coefficient of 4 kinds of sound absorptive inner membrane with outer membrane was tested in the reverberation chamber. Sound absorption coefficient of mid frequency range was about 0.4 ~ 0.6. Also, sound absorption coefficient was changed by the air space behind the membrane material. Secondly, sound field control performance was investigated using mock-up space. By the installation of sound absorption membrane material, reverberation time was decreased and speech intelligibility was increased. Finally, thermal resistance and room temperature in two kinds of mock-up rooms were tested, simultaneously. Results of thermal properties showed thermal insulation properties ware increased by adding inner membrane material underneath the outer membrane.

• 콘크리트학회논문집
• /
• 제20권5호
• /
• pp.653-660
• /
• 2008

본 연구는 펄라이트를 이용한 흡음재료의 흡음성능을 개선시키기 위한 최적배합에 대한 분석을 실시하였다. 결합재로서 폴리머 시멘트 슬러리와 무기질 결합재를 사용하여 흡음재료를 각종 배합조건에 따라 제작하여, 강도, 동결 융해 저항성, 그리고 흡음성능에 대하여 실험을 실시하였다. 실험 결과, 관내법에 의한 흠음재의 흠음계수는 배합에 따라 약간의 차이가 있으나 폴리머 디스퍼션을 결합재로 사용한 경우 흡음재의 감음계수 (NRC)는 $0.48{\sim}0.51$로 시멘트만 결합재로 사용한 경우에 비해 약간 크게 나타났으나, 방음벽의 환경부 고시 기준에서의 흡음재로서 감음계수 0.70에 비하면 낮은 수치이다. 그러나 잔향실법에 의한 흡음용 패널의 저주파수 영역($250\;Hz{\sim}500\;Hz$)에서 흡음계수가 $0.84{\sim}1.00$로 매우 높게 나타났으며, 고주파 영역에서도 $0.57{\sim}0.77$ 정도로 비교적 높은 흡음률을 나타내 감음계수가 0.77로 높게 나타났다. 폴리머 디스퍼션을 결합재로 사용한 흡음재는 압축강도, 휨강도 및 동결융해 저항성 등에서 방음벽 재료로서 적당한 성능을 발휘하였으며, 성능과 가격면에서 밸런스를 확보할 수 있는 배합을 도출할 수 있었다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.964-968
• /
• 2007

A helmholtz resonator has been widely used for the purpose of suppressing low frequency noises propagated from various heat and fluid machineries. However, the resonator has demerits that the absorption bandwidth at resonance frequency is very small and a large cavity is necessary. In order to overcome these problems, in this paper, a resonator with perforated panels at the neck and/or in the cavity is proposed. The absorption performances of resonators are measured by two-microphone method and are estimated by transfer matrix method. The experimentally measured values of normal absorption coefficients are agreed well with the corresponding values from the transfer matrix method. By introducing perforated panels at the neck of a resonator, it is shown that the absorption performances and bandwidth have a significant improvement.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.886-889
• /
• 2002

흡음률을 평가하기 위한 연구로서 임피던스 튜브를 통한 수직입사 흡음률과 잔향실을 이용한 랜덤입사 흡음률에 대한 실험연구를 수행하였다. 한편 수직입사와 랜덤입사와의 상관관계를 실험 연구를 통하여 조사하였다. 이 상관관계는 주파수에 따라서 다르게 나타나고 있다. 저주파수 대역에서는 랜덤 입사가 수직입사 보다 크게 나타나고 있지만 고주파수에서는 수평입사 성분의 영향으로 랜덤입사에서는 감소하는 경향을 보이고 있다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.877-882
• /
• 2002

A new estimation model of predicting the sound absorption performance for multiple perforated plate sound absorbing system was developed using transfer matrix method. The proposed method was validated by comparing the calculated absorption coefficients of a single layer perforated plate with the values measured by the two-microphone impedance tube method far various porosity and cavity depth. The developed transfer matrix method was further applied to estimate the multiple layer perforated plates and it is shown that the estimated absorption coefficients generally agree well with the measured values.

• 한국소음진동공학회논문집
• /
• 제15권9호
• /
• pp.1003-1008
• /
• 2005

The acoustic absorption of a multiple layer perforated plate system is very good near the resonance frequency region, while it has been regarded as a demerit that its frequency bandwidth is considerably narrow. In order to overcome such a demerit, the parallel perforated plates with different porosities are proposed. The sound absorption of such system composed of a parallel perforated plate is calculated by an equivalent electroatoustic circuit approach and validated by comparing the calculated absorption coefficients with those measured by the two-microphone impedance tube method. The sound absorptive characteristics and performance of parallel perforated plate systems are discussed from a standpoint of frequency bandwidth related with sound absorption.

• 한국소음진동공학회논문집
• /
• 제12권9호
• /
• pp.709-716
• /
• 2002

A practical method of predicting the sound absorption coefficient for multiple perforated-plate sound absorbing system was developed using transfer matrix method. The proposed method was validated by comparing the calculated absorption coefficients of a single layer perforated plate with the values measured by the two-microphone impedance tube method for various porosity and spacing of the perforated plate. The developed transfer matrix method was further applied to estimate the multiple layer perforated plates and it is shown that the estimated absorption coefficients agree well with the measured values.