• Journal of electromagnetic engineering and science
• /
• v.4 no.1
• /
• pp.37-42
• /
• 2004

In this paper, LNB(low noise block) downconverter MMIC is designed for Ku-band satellite communication system using InGaP/GaAs HBT high linear process. Designed MMIC consists of low noise amplifier, double balanced mixer, and IF amplifier with a total chip area of 2.6${\times}$1.1 $\textrm{mm}^2$. Designed MMIC has the characteristics of over 37.5 ㏈ conversion gain, 14 ㏈ noise figure, ripple of 3 ㏈, and output-referred $P_{1dB}$TEX>(1 ㏈ compression power) of 2.5 ㏈m with total power dissipation of 3 V, 50 mA.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.2
• /
• pp.100-105
• /
• 2006

In this paper, a low noise amplifier(LNA) in a receiver of a low noise block down converter (LNB) for direct broadcasting service(DBS) is implemented using GaAs HEMT. The LNA is designed for the bandwidth of 11.7 GHz-12.2 GHz. The two-stage LNA consists of a input matching circuit, a output matching circuit, DC-blocks and RF-chokes. Experimental results of the LNA show the noise figure less than 1.4 dB, the gain greater than 23 dB and the flatness of 1 dB in the bandwidth of 11.7 to 12.2 GHz.

• Journal of electromagnetic engineering and science
• /
• v.9 no.3
• /
• pp.130-140
• /
• 2009

The design theory and experimental results of a true random noise radar system are presented in this paper. Target range information can be extracted precisely by correlation processing between the delayed reference and the signal received from a target, and the velocity information by the Doppler processing with successive correlation data. A K-band noise radar system was designed using random FM noise signal, and the characteristics of the fabricated system were examined with laboratory and outdoor experiments. A C-band random FM noise signal was generated by applying a low-frequency white Gaussian noise source to VCO(Voltage Controlled Oscillator), and a K-band Tx noise signal with 100 MHz bandwidth was obtained by using a following frequency multiplier. Two modified wave-guide horn arrays were designed and fabricated, and used for the Tx and Rx antennas. The required amount of Tx/Rx isolation was attained by using a coupling cancellation circuit as well as keeping them apart with predetermined spacing. A double down-conversion scheme was used in the Rx and reference channels, respectively, for easy post processing such as correlation and Doppler processing. The implemented noise radar performance was examined with a moving bicycle and a very high-speed target with a velocity of 150 m/s. The results extracted by the Matlab simulation using the logging data were found to be in a reasonable agreement with the expected results.

• Proceedings of the KSRS Conference
• /
• 2004.10a
• /
• pp.577-580
• /
• 2004

To overcome with large size noise source distribution network design difficulty in interferometric radiometer system, especially for sub-Y-type array, a new on-board calibration technique using noise re-radiation is proposed in this paper. The suggested calibration technique is using noise re-radiation effect of center antenna after noise source injection from matched load. This approach is especially proper to sub-Y-type array interferometric synthetic aperture radiometer in mm-wave frequency band. Compared with noise injection network of a conventional synthetic aperture radiometer, the system mass, volume, and hardware complexity is reduced and cost-effective. Only one internal noise source, matched load, is used for injection using noise re-radiation technique a small set of sub-Y receiver channels is calibrated. Detailed calibration scenario is discussed and simulation results about noise re­radiation effect are presented.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1273-1279
• /
• 2000

A new concept of piezoelectric smart panels for noise reduction in wide band frequencies is proposed and their possibility is experimentally investigated. The proposed panels are based on active and passive methods. They use piezoelectric smart structure technology for active noise reduction at low band frequencies and passive sound absorbing materials for mid-range of noise frequencies. To prove the concept of piezoelectric smart panels, an acoustic measurement experiment was performed. The smart panels exhibit a good noise reduction in middle and high frequency ranges due to the mass effects of absorbing materials or/and the air gap. The use of piezoelectric smart panel renders noise reduction large at resonance frequency. Another concept of smart panel that uses piezoelectric damping is experimentally investigated. Since piezoelectric dampings can reduce vibration and noise at resonance frequencies with simple shunt circuit, they have merits in terms of economy and simplicity. Dissipated energy method(DEM) is adopted to tune the shunt circuit precisely in piezoelectric dampings. Noise reduction at multiple resonance frequencies is demonstrated.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.12
• /
• pp.2068-2072
• /
• 1997

Acoustic noise has become an increasingly important issue, especially in the industrial environment. Nowadays home and office are not exceptional, mainly due to the increase in the usage of machinery. Active Noise Control(ANC) becomes efficiently an available tool for the noise suppression with rapid advances of solid state electronics. In this study an ANC system is developed for audio headphone to work as a noise protector, so called an ear-muff. The system is developed to kill a certain frequency band noises selectively which is purposed to suppress only the dominant ambient noise such that normal numan conversation is not disturbed with wearing the ear-muff. For the purpose, an ANC design strategy is suggested and implemented with an analogue control circuit. The performance is evaluated by frequency response test, which shows well consistence with theoretical one. The results are so satisfactory that noise of 640 Hz, which is aimed to suppress, is reduced by 20db without significant distortion in other frequency band.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.4
• /
• pp.427-435
• /
• 2011

This paper deals with the measurement and analysis of the squeal noise according to the curvature of rail. The squeal noise is generated by the friction between the railway with curve and the wheel. The squeal noise is a big problem in Busan Metro Line 3. If the developing panel type ANC(Active Noise Control) system which is attached to the floor can reduce 5 dB in below 500 Hz, the sound pressure level of the whole band pass can be reduced about 4-4.8 dB in squeal noise above the curvature of R400. Curve squeal noise is the intense high frequency tonal that can occur when a railway vehicle transverses a curve. The frequency range is from around 500 to almost 20,000 Hz, with noise levels up to about 15 dB in curve.

• The Journal of the Korea Contents Association
• /
• v.17 no.5
• /
• pp.491-498
• /
• 2017

This study is to determine the significant effect of white and pink noise on brain. The brain synchronization has been analyzed under the condition of non-noise, white nose and pink noise(male 10, female 10, mean age $23.3{\pm}2.14$). As a result of analysis, pink noise stimulus, alpha, low beta band, and high beta band were significantly decreased than non-noise and white noise. In addition, these brain response pattern significantly increased at frontal lobe and temporal lobe, and dominated on the right hemisphere. This result is considered to be useful of sound design in driving quality of human life on the basis of neuroscience.

• Proceedings of the IEEK Conference
• /
• 2003.11c
• /
• pp.64-67
• /
• 2003

This paper presents the design of dual-band VCO using PBG structure for IEEE 802.11A/B. By adding switch circuit to the single-band VCO, we could achieve a dual-band VCO. The center frequencies of dual-band VCO are 5.93GHz(-13dBm) and 2.37GHz (3.50dBm). The phase noise is improved about l0dB by using PBG Structure.

• Journal of electromagnetic engineering and science
• /
• v.16 no.3
• /
• pp.164-168
• /
• 2016

A dual-band through-the-wall imaging radar receiver for a frequency-modulated continuous-wave radar system was designed and fabricated. The operating frequency bands of the receiver are S-band (2-4 GHz) and X-band (8-12 GHz). If the target is behind a wall, wall-reflected waves are rejected by a reconfigurable $G_m-C$ high-pass filter. The filter is designed using a high-order admittance synthesis method, and consists of transconductor circuits and capacitors. The cutoff frequency of the filter can be tuned by changing the reference current. The receiver system is fabricated on a printed circuit board using commercial devices. Measurements show 44.3 dB gain and 3.7 dB noise figure for the S-band input, and 58 dB gain and 3.02 dB noise figure for the X-band input. The cutoff frequency of the filter can be tuned from 0.7 MHz to 2.4 MHz.