• Journal of the Korean GEO-environmental Society
• /
• v.4 no.1
• /
• pp.41-48
• /
• 2003

This study analyzed the correlation between the engineering characteristics of soils, and the CBR values in order to figure out the eligibility of quality criteria as construction materials, by attempting to reduce time and costs for the CBR testing and predicting the results of the CBR testing. The study also analyzed the correlation between the percent passing of No.200 sieve, liquid limit and compaction characteristics, on the basis of the soil testing data conducted at the Yeongdong construction area. This study will provide necessary data for road pavement plans and designs by analyzing the correlation between the percent passing of No.200 sieve, the degree of activity and the swelling rate, and suggest the correlation formula with each soil.

• Journal of the Korean Geotechnical Society
• /
• v.27 no.6
• /
• pp.81-95
• /
• 2011

This study investigates relative density test of standard sand and bottom ash which were devided into No.40, No.60, No.100, No.200 and resonant column tests were conducted for samples with the relative density of 40%, 55%, and 70% on the basis of the test results. Resonant column tests were also conducted for each residual bottom ash which contains the passing sample of No.200 with the relative density of 55%. By compressing each residual sample with the compaction energy of A-compact mold test, the passing percentage of No.200 sieve increased up to 30%, which led to the adjustment of relative density to 10%, 20%, and 30%. Test results show that maximum shear modulus and damping ratio of bottom ash are smaller than those of standard sand because crushing strength and unit weight of the former are smaller than those of the latter.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.3
• /
• pp.535-543
• /
• 2016

This study has been carried out to evaluate the CBR characteristics and the correlations among every soil properties of National road in Yeongnam region. Total of 480 soil samples were collected from 41 administrative districts for more than 30 years. Their physical and mechanical properties such as natural water content, the Atterberg limit, No. 200 sieve passing, the compaction test and the CBR test results were involved. The soils in Yeongnam region, SM, SC, SP and CL by USCS have predominated approximately 79%. The test results show that average CBR values of gravel and sand range from 12.7% to 20.3% and those of silt and clay range from 4.8% to 7.1%. It means that average CBR values of fine grained soils are less than a half of coarse grained one. Natural water content, No. 200 sieve passing, optimum moisture content and maximum dry density of soils are well correlated with CBR values. Especially, it presents that No. 200 sieve passing is the best correlation factor with CBR value. If consider the partition off this region into 6 zones of classified by mother rock, the correlation between CBR value and every soil properties tends to increase. It is suggested that tables, figures and the regressions described in this paper may be available for designers and engineers to understand the characteristics of an embankment materials in Yeongnam region.

• Geotechnical Engineering
• /
• v.12 no.6
• /
• pp.139-152
• /
• 1996

In order to treat flow problems for unsaturated soils, it is necessary to obtain the soil-water characteristic curves which show nonlinear relationship between metric suction and volumetric water content. With two different pleasuring devices, measurements of the matric suction were taken for Jumoonjin sand, Hangang sand, and weathered granite soils with different fined. Experimental parameters which can describe experimental formulas for the soil-water characteristics were determined by using the data obtained from the experiment. Among experimental formulas of previous researchers, that of van Genuchten(1980) agreed well with the results of experiments. For weathered granite soils, the parameters increased with the increase of fine contents, Therefore, the soil-water characteristic for a weathered soil can be estimated by using Parameters corresponding to its fine contents.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.03a
• /
• pp.773-778
• /
• 2002

강우시 불포화 자연사면의 파괴메커니즘을 규명하기 위하여 사면내 모관흡수력의 변화를 고려한 안정해석을 수행하였다. 사면에는 강우계, Tensiometer, Pizometer, Water mock, 경사계 등이 설치되었으며 강우시 사면내 부간극수압과 임시지하수위의 거동을 관찰하였다. 실내실험으로부터 불포화 사면의 안정해석을 위하여 입력 값으로 사용되는 불포화투수계수, 불포화강도정수를 시료의 No.200체 통과량과 건조밀도를 기준으로 경험계수를 이용하여 추정 사용하였다. 강우의 침투로 인한 사면내 부간극수압의 분포는 계측값과 수치해석결과가 차이를 보였으며 이는 불포화 흐름시 흙속의 공기의 영향, 강우의 나무와 수풀에 의한 중간차단효과 및 증발의 영향을 해석에 고려하지 못했기 때문으로 사료된다. 사면안정해석결과 강우초기 모관흡수력을 고려하는 경우 약 10%의 안전율의 증가를 나타냈으며, 침투가 진행되면서 그 차이는 좁아져 임시지하수위가 표층까지 도달했을 때 흡수력을 고려하지 않는 해석과 안전율은 일치하였다.

• Korean Journal of Agricultural Science
• /
• v.10 no.2
• /
• pp.277-291
• /
• 1983

In order to investigate the shear characteristics of earth structure after construction. Four sample soils with different gradation were selected and compacted under the optimum moisture content and the maximum dry density. And the direct shear test and the triaxial compression test were performed with those sample soils under various pre-compression loads. The results were summarized as follows; 1. With the increase of the percent passing of No. 200 sieve, the cohesion of soil increased regularly and the internal friction angle of soil decreased with slow ratio. 2. The pre-compression increased the shear strength of compacted cohesive soil. The increase of cohesion was very apparent but the internal friction angle didn't show such regular tendency. 3. With the increase of pre-compression load, the slope of stress-strain curve showed steep at the early stage of horizontal strain. The vertical strain was small at the compression stage and big at the expansion stage. 4. When the vertical stress of shear test with increase in the horizontal strain was small, stress ratio(shear stress vs. vertical stress) of sample showed the largest value and the slope of stress ratio curve showed also steep. 5. When the sample was had the same condition, the cohesion of soil showed bigger value in the triaxial compression test and the internal friction angle of soil showed bigger value in the direct shear test.

• Journal of Korean Society of Transportation
• /
• v.24 no.5 s.91
• /
• pp.35-44
• /
• 2006

Acceleration and deceleration curves have been used for design purposes worldwide. The curve in design level has been regarded as an single deterministic curve to be used for design of climb lanes. It should be noted that the curve was originally made using ideal driving truck and that the curve is applied during design based on the assumption of no difference between ideal and real driving conditions. However. observations show that aged vehicles and lazy behavioring drivers nay make lower performance of vehicles than the ideal performance. The present paper provides the results of truck speeds at climbing lanes then probabilistic variation of acceleration and deceleration corves. For these purposes. a study about identification of vehicle makers, and weights for trucks at freeway toll gates and then observation of vehicle-following speed were performed. The 85%ile results obtained were compared with the deterministic performance curves of 180, 200, and 220 Ib/hp. It was identified that the performance of 85%ile results obtained from vehicle-following-speed observations were lower than one from deterministic performance curves. From these results, it may be concluded that at the beginning Point of climbing lanes additional $16.19{\sim}67.94m$ is necessary and that at the end point of climbing lanes $53.12{\sim}103.24m$ of extension is necessary.

• Journal of the Korean Wood Science and Technology
• /
• v.14 no.1
• /
• pp.3-44
• /
• 1986

In order to obtain the basic physical and mechanical properties of steel wire reinforced particleboard, particleboards were formed with large particles through 2.11 mm (12 meshes) and retained on 1.27mm (20 meshes) sieves and small particles through 1.27mm (20 meshes) and retained on 0.42mm (60 meshes) sieves from the plywood mill wastes of meranti (Shorea spp.) in the form of pallmanchips, applying urea-formaldehyde resin as an adhesive on the particle surface in 10 percent on the oven dried weight of particles, and arranging steel wires of 1mm in diameter 5,10,15,20, and 25mm in longitudinal and transverse direction with crossing in the mid of the board depth in single layer boards, 10mm in longitudinal or transverse direction without crossing in two layers and 10mm in longitudinal and transverse directions with and without crossing in three steel wire layers boards. The stepwise 9-minutes-multi-pressing schedule in 5 minutes at 35 kgf/$cm^2$, 2.5 minutes at 25 kgf/$cm^2$. and 1.5 minutes at 15 kgf/$cm^2$ was applied for $300{\times}200{\times}13$mm board at the temperature of 160$^{\circ}C$ in a hot press. Specific gravity, thickness swelling, bending properties of modulus of rupture (MOR), modulus of elasticity(MOE), work to proportional limit, and work to ultimate load, internal bond (IB), and screw holding power(SHP) of the reinforced boards were analyzed on the wire openings and wire layers. The results obtained are summarized as follows; 1) In specific gravity, particleboards with large particles and small particles had higher value with more steel wire placements and more steel layers composition, 2) Particleboards with large particles in accordance with more steel wire liners composition gave very poor thickness swelling. 3) The mechanical properties of particleboards formed with large or small particles were reinforced with more steel wire layers. Therefore, bending strength was improved in modulus of rupture, modulus of elasticity, and work to ultimate load. Especiallv, particleboards with two or three steel wire layers showed the tension lamination effect when the steels in lower steel wire layer were oriented parallel to the board length. 4) The modulus of rupture, modulus of elasticity, and work to ultimate load in bending varied with opening area, distance of lengthwise wires multipled by distance of transverse wires. Particleboards formed with large particles resulted in higher value in modulus of rupture with 1.5-3 $cm^2$ opening area, 1-2cm distance between transverse wires, and 1.5-2.5cm distance between lengthwise wires. Particle boards formed with small particles showed higher value with 0.5-1.5$cm^2$ or 3.75-6.25 $cm^2$ opening area, 0.5 or 2.5cm distance between transverse wires. 5) In modulus of elasticity, particleboards formed with large particles with one steel wire layer suggested higher value with 5-3$cm^2$ opening area, 1-2.5cm distance between transverse wires and also 1-2.5 cm distance between lengthwise wires. Particleboards formed with small particles showed higher value with 0.75-1.25$cm^2$ or 3-6.25$cm^2$ opening area and 0.5 or 2.5cm distance between transverse wires. 6) Particleboards formed with large particles gaved higher value in work to ultimate load with 1-3$cm^2$ opening area. Particleboards formed with small particles showed increasing tendancy with decreasing opening area. 7) In internal bond and screw holding power, particleboards formed with large particles had increasing value in two and three steel wire layers compositions, but particleboards formed with small particles showed no difference. Particleboards formed with large particles containing one steel wire layer showed no difference in internal bond and screw holding power, and particleboards formed with small panicles containing one steel wire layer resulted in increasing value in internal bond and decreasing value in screw holding power in accordance with increase in opening area.