• 한국안전학회지
• /
• 제35권3호
• /
• pp.6-15
• /
• 2020

This study examined the structural behaviors and ultimate loads of assembled system scaffolds by load tests. Considering the number of bay and bracing installation, four specimens were tested. The bays were divided into 1 bay and 2 bays, with and without the bracing member installed. Failure modes and horizontal displacements show that the whole column buckled without showing no point of inflection in the column, regardless of whether or not braces were installed. Thus, the current design method of selecting the vertical spacing between the horizontal members of the system scaffold as the effective buckling length underestimates the effective buckling length. In case of 1 bay specimens, the ultimate loads between specimens with and with bracing members are similar. However, in case of 2 bay specimens, the specimen with bracing members shows the increased ultimate load of 36% compared with that without bracing members. In addition, as the number of bays in the system scaffold increases, the ultimate load of the unit vertical column increases in case of the specimen with bracing installation. However, in the specimen without bracing members, the ultimate load of the unit column reduces with the increment of the number of bays due to the torsional buckling. Therefore, it is essential to install bracing members to increase the whole strength of system scaffolds and the ultimate load of the unit column.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2007년도 추계학술대회 및 제23회 정기총회
• /
• pp.228-229
• /
• 2007

컨테이너 크레인은 강풍으로부터 보호를 받기 위한 차폐물이 없는 곳에 존재하기 때문에 이상 기후 조건에 취약성이 있는 구조물이다. 본 연구에서는 풍향변화에 따라 컨테이너 크레인에 작용되는 풍하중을 분석하기 위하여 수행되었다 사용된 모델은 61톤 급 컨테이너 크레인으로 현재 항만시설에 많이 사용되는 모델이다. 유동장은 원통으로 모델링하였으며, 직경 500m, 높이 200m로 설정하였다. 본 연구에서는 건축물 하중기준의 풍하중 설계기준에 따라 풍하중을 적용하였으며 풍향에 따른 영향을 분석하기 위해서 유동장을 10$^{\circ}$간격으로 분할하였다. 이를 바탕으로 CFX-10을 사용하여 전산유동해석을 수행하고 이를 통하여 얻어진 결과와 풍력실험 결과를 비교 연구함으로써, 컨테이너 크레인의 구조설계에 필요한 풍하중을 분석하였다.

• 한국공작기계학회논문집
• /
• 제13권6호
• /
• pp.23-28
• /
• 2004

Impact behavior of polycarbonate in various defect state was investigated using an instrumented impact tester. A method of analyzing raw impact data was developed and successfully demonshsted the impact behavior in terms of load-displacement and energy-displacement curves. This technique was shown to be capable of separating defect no-defect initiated fractures as well as their propagation behaviors.

• 폴리머
• /
• 제26권2호
• /
• pp.270-278
• /
• 2002

저밀도 2-D 탄소/탄소 복합재료의 저속 충격에 의한 파괴 거동과 첨가제에 따른 충격 에너지 흡수 경향을 연구하였다. 저속 충격시험은 mini tower 낙추 충격 시험기를 이용하였으며, 흑연, 카본블랙, 분쇄탄소섬유를 첨가제로 선택하였다. 흑연의 첨가는 최대하중값을 증가시켰으며, 전체적인 관통이 일어나기까지 응력을 오랫동안 유지시키는 효과를 나타내었다. 특히 9 vol%의 함량에서 흑연이 첨가되지 않은 씨편보다 약 42%의 충격 흡수 개선을 보였다. 약 0.4 J의 낮은 충격에너지에 의한 충격 회수에 따른 실험에서 첨가제가 첨가되지 않은 시편의 경우, 충격에너지는 층간분리에 의해 소모되고, 흑연의 함량이 증가함에 따라 파괴 경향은 시편의 관통으로 변화함을 관찰할 수 있었다.

• Nuclear Engineering and Technology
• /
• 제55권9호
• /
• pp.3342-3351
• /
• 2023

High-density polyethylene (HDPE) pipelines in nuclear power plants (NPPs) have to meet high requirements for seismic performance. HDPE pipes have been proved to have good seismic performance, but joints are the weak links in the pipelines, and pipeline failures usually initiate from the defects inside the joints. Limited data are available on the seismic performance of butt-fusion joints of HDPE pipelines in NPPs, especially in terms of defects changes inside the joints after earthquakes. In this paper, full-scale shaking table tests were performed on a test section of suspended HDPE pipelines in an NPP, which included straight pipes, elbows, and 10 butt-fusion joints. During the tests, the seismic load-induced strain of the joints was analyzed by strain gauges, and it was much smaller than the internal pressure and self-weight-induced strain. Before and after the shaking table tests, phased array ultrasonic testing (PA-UT) was conducted to detect defects inside the joints. The locations, numbers, and dimensions of the defects were analyzed. It was found that defects were more likely to occur in elbows joints. No new defect was observed after the shaking table tests, and the defects showed no significant growth, indicating the satisfactory seismic performance of the butt-fusion joints.

• 대한기계학회논문집B
• /
• 제37권12호
• /
• pp.1129-1135
• /
• 2013

본 연구에서는 저발열량 천연가스가 현재 상용되고 있는 대형 천연가스 엔진에 미치는 영향을 살펴보기 위하여 3종류의 연료를 적용하였다. 전부하 운전조건과 WHSC 및 WHTC 모드 테스트를 수행하여 엔진성능 및 배기특성을 분석하였다. 실험결과 전부하 실험에서 토크성능이 $9,800kcal/Nm^3$의 발열량을 갖는 저발열량 가스의 경우 현행 천연가스($10,400kcal/Nm^3$)를 사용한 결과에 비해 4.4% 감소하였다. 저발열량 연료를 사용하였을 때 일산화탄소, 이산화탄소 및 질소산화물의 배출량은 감소하였지만, 탄화수소의 배출량은 증가하였다. WHSC 및 WHTC 실험결과 저발열량 연료에서 열효율이 증가하였으며 배기특성은 전부하 실험결과와 유사한 경향을 보였다. 저발열량 천연가스를 사용할 경우 제원상의 출력을 만족하기 어렵고, 탄화수소의 배출이 증가하는 문제점을 확인하였다.

• 한국정보통신학회논문지
• /
• 제5권7호
• /
• pp.1308-1313
• /
• 2001

본 논문은 3상 유도전동기의 파라미터 측정정법과 기동특성을 제시한다. 고정자 권선저항, 구속 및 무부하시험에 의해 측정된 유도전동기 파라미터를 이용하여 전동기의 기동특성을 시뮬레이션 하였다. 또한 유도전동기 축에 스트레인 게이지를 부착하여 기동토크에 대한 특성을 실험으로 확인하고 이를 시뮬레이션 결과와 비교 분석하여 그 타당성을 검증하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 B
• /
• pp.849-851
• /
• 2001

This paper presents experimental method of parameter measurement and starting characteristics of 3 phase induction motor. Equivalent circuit parameters measured by DC test, the blocked rotor test, and no load test were used as the input data for computer simulation. Starting characteristics, such as starting current and torque were analyzed through computer simulation by Matlab, and the simulation results were compared with experiment using strain gauge attached on motor shaft. We conform that experimental results are very similar to that of simulation.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 봄 학술발표회 논문집(I)
• /
• pp.691-696
• /
• 1999

This paper is aimed to investigate flexural rehabilitation effect o pre-loaded reinforced concrete beams strengthened by carbon fiber sheet. Main Test parameters are reinforcement ratio and the magnitude of pro-loading and seven test beams are analyzed rehabilitation effect by carbon fiber sheet, load-deflection, failure mode, stress of reinforcing bar by the magnitude of pre-loading. Test results show that internal force was showed pre-loaded specimens lower than no-loaded specimens during rehabilitation and changing stiffness was showed in the same was and failure mode showed brittle failure from all specimens.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 Proceedings ICPE 98 1998 International Conference on Power Electronics
• /
• pp.287-292
• /
• 1998

This paper presents some results of performance evaluation test via actual machines of a new hybrid vector control utilizing a new indirect orientation scheme and stable filter embedded direct orientation scheme for induction motors without speed or position sensor. It is shown through the test by 0.3(kW) and 3.7(kW) motors that the proposed sensorless vector control has the following high potentialities: 1) speed range is 0 to 600(rad/s) or more, 2) zero-speed command is accepted and settles the machines at a stable standstill with no vibration 3) it can make machines to track variable command of acceleration and deceleration $\pm$6,000(rad/s2), 4) it can make machines to drive directly load of at least 26 times larger inertia than that of the machine, 5) it can make machines to produce much larger torque than the rating in torque control mode even at standstill. The performance confirmed by the test is far away for previous schemes or sensorless drive apparatuses.