• Journal of the Korean Ceramic Society
• /
• v.43 no.2 s.285
• /
• pp.92-97
• /
• 2006

Dolomite type $BaSn(BO_3)_2$ ceramics with rhombohedral crystal structure has been synthesized via solid state reaction route. Dielectric properties were measured for the samples sintered at $1050\~1200^{\circ}C$ for 2 h in air. Dielectric constant, loss tangent, and temperature coefficient were increased with sintering temperature due to the evolution of $BaSnO_3$, secondary, phase. Optimum dielectric properties were obtained at the $BaSn(BO_3)_2$ ceramics sintered at $1100^{\circ}C.\;CuO/Bi_2O_3$ was added to $BaSn(BO_3)_2$ ceramics to lower the sintering temperature for LTCC application, then Co and Fe-based coloring agents were added for colorizing the LTCC tape. Typical dielectric properties of $BaSn(BO_3)_2$ ceramics with $5 wt\%\;CuO/Bi_2O_3\;and\;3wt\%$ Co-coloring agent that sintered at $900^{\circ}C$ were $\varepsilon_r=9.89,\;tan{\delta}=0.92\times10^{-3},\;and\;TCC=112ppm/^{\circ}C$. Thus obtained LTCC tape was co-fired with Ag paste for compatibility test and revealed no sign of Ag reaction with the ceramics.

• Journal of Sensor Science and Technology
• /
• v.23 no.4
• /
• pp.266-271
• /
• 2014

Chemical sensors are used in various industrial facilities such high-risk and prevent the leakage of substances, important in life and environmental protection and the safe use of industry, used for management. In particular, high-temperature environments such as power generation equipment of the rotating part due to leakage generated by the various oil, power plants Shut Down, fire, work environment (exposure to various chemical solution and gas leak) and various water, air and soil pollution causes. Thus, over the long term through various channels such as crops and groundwater contamination caused by the slow, serious adverse effect on the ecosystem. In this paper, synthetic lube oil and high pressure hydraulic fluid leakage and immediately detect a new Printed Electronic implementation of technology-based film-type sensors, and its performance test. Thus, industrial accidents and environmental pollution and for early detection of problems, large accidents can be prevented. Experimental results of the synthetic lube oil and high pressure hydraulic fluid solution after the contact time depending on the experiment and the oil solution of the sensor material of the conductive porous PE resistance value by a chemical reaction could be confirmed that rapid increase. Also implemented in the film-type oil sensor electrical resistance change over time of the reaction rate and the synthetic lube oil is about 2 minutes or less, the high pressure hydraulic fluid is less than about 1 minute was. Therefore, more high-pressure hydraulic fluid such as a low volatility synthetic lube oils are the resistance change and the reaction rate was confirmed to be the slowest.

• Journal of Electrical Engineering and Technology
• /
• v.11 no.1
• /
• pp.184-191
• /
• 2016

In recent years, there are a number of studies that have been carried out to explore the alternative for Mineral Oil (MO) as dielectric insulating fluid in transformers due to the increasing tight regulation on safety and environment. Vegetable oils have been identified as suitable candidate since it is biodegradable, non-toxic and high flash/fire points which ensure more in-service safety. Among the types of vegetable oils considered for transformers application are Palm Oil (PO) and Coconut Oil (CO). This paper presents an experimental study on the lightning breakdown voltages of PO and CO under non-uniform electric field based on needle-sphere electrodes configuration at 3 small gap distances. The type of PO used in this study is Refined Bleached and Deodorized Palm Oil (RBDPO) Olein. The main focus of this study is to examine the lightning breakdown performance of RBDPO and CO under different test conditions and assess its suitability as dielectric insulating fluid in transformers. The effect of voltage polarities (positive and negative) and testing methods (rising-voltage, up-and-down and multiple-voltage) were investigated. The data obtained from all tests were analysed by Weibull distribution in order to determine the withstand voltages for each type of oils. It was found that the breakdown voltages of RBDPO and CO are comparable with MO under positive lightning impulse. Under negative lightning impulse, the breakdown voltage of MO is slightly higher than RBDPO and CO. There is no significant effect of testing methods and voltage polarities on lightning breakdown voltages of RBDPO and CO. Based on the statistical analysis, it is found that the breakdown voltages of RBDPO and CO at 1% probability are slightly lower than MO.

• Journal of the Society of Disaster Information
• /
• v.13 no.4
• /
• pp.422-441
• /
• 2017

Notifying emergency evacuation methods, accurate disaster location and evacuation route guidance can be very active alternatives to quickly minimize evacuation and casualties in disaster situation in the development of subway disaster prevention detection system that detects the disaster signs at the subway station early on the basis of Internet of things and leads passengers to evacuate. It's not easy to ensure perfect functioning of fire fighting facilities and equipments due to underground space structure with narrow exits. Therefore, we developed disaster provision EL Display integrated board that can induce the most efficient evacuation and the field experiment was conducted to examine the practical application in this study. Especially the applicability was verified by field application test because there is no case in which EL panels are used to evacuate disasters.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.15 no.3
• /
• pp.11-19
• /
• 1988

The purpose of this study is to investigate ways to control the wind dispersal of contton-wrapped seeds of such poplars and willows as Poplus alba, P. tomentiglandulosa, P. euramericana, P. deltoides, and Salix pseudo-lasiogyne. These trees are hated by many people because of their seeds blowing all over the place during May. These cottony seeds can be nuisance to various types of outdoor activities, pose safely threat to drivers, become fire hazards during prolonged spring dry spells, and cause many types of health hazards of allergy such as sneezing. rhinitis, asthma, and skin rashes. Four control methods can be used to resolve the problem. First, pruning can be a solution, but it is unsatisfactory in terms of costs and outcome. Second, planting of male trees only can be a solution, but it is hard to identify sexes of saplings. Third, female trees can he replaced with other species. But it requires high costs and takes at least ten years to functionally replace the removed ones. As an alternative to such unsatisfactory control methods, the possibility of applying plant growth regulators has been investigated since 1983. During the pre-test, various concentrations and mixtures of them were either sprayed or injected, but failed to achieve any promising results. But the injection of a mixture made up of 0.75g of 2-chloroethane phosphonic acid with 0.2 mg of GA in 300cc water in the end of March produced premature falling of almost all aments and capsules of treated poplars and willows. It was found that the effect of the injection lasts two years. The results of the main experiment of 1987 can be summarized as follows ; First, the injection of the mixture of 2-chloroethane phosphonic acid and GA increases the premature abscisin of aments and capsules, thus reducing the wind dispersal of the cottony seeds of S. pseudolasiogyne, P. tomentiglandulosa, and P. euramericana 1644.09, 1200.61, and 1485.11 times, respectively, than that of the naural abscisin, It is estimated that the average number of wind-blown seeds reduced are approximatively 6,185,100, 4062,900, and 2,830,670 per tree, respectively. Second, the treatment causes no observable side effects on the growth of the samples tested.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.28 no.2
• /
• pp.143-149
• /
• 2022

PCS needs to freely switch AC and DC to connect the battery, external AC loads and renewable energy in both directions for energy efficiency. Whenever converting happens, power loss inevitably occurs. Minimization of the power loss to save electricity and convert it for usage is a very critical function in PCS. PCS plays an important role in the ESS(Energy Storage System) but the importance of stabilizing semiconductors on PCB(Printed Circuit Board) should be empathized with a risk of failure such as a fire explosion. In this study, the temperature variation inside PCS was reviewed by cooling fan on top of PCS, and the vibration characteristics of PCS were analyzed during truck transportation for reliability of the product. In most cases, a cooling fan is mounted to control the inner temperature at the upper part of the PCS and components generating the heat placed on the internal aluminum cooling plate to apply the primary cooling and the secondary cooling system with inlet fans for the external air. Results of CFD showed slightly lack of circulating capacity but simulated temperatures were durable for components. The resonance points of PCS were various due to the complexity of components. Although they were less than 40 Hz which mostly occurs breakage, it was analyzed that the vibration displacement in the resonance frequency band was very insufficient. As a result of random-vibration simulation, the lower part was analyzed as the stress-concentrated point but no breakage was shown. The steel sheet could be stable for now, but for long-term domestic transportation, structural coupling may occur due to accumulation of fatigue strength. After the test completed, output voltage of the product had lost so that extra packaging such as bubble wrap should be considered.

• Journal of Food Hygiene and Safety
• /
• v.13 no.3
• /
• pp.252-257
• /
• 1998

Bamboo salt has been used as a traditional remedy for gastric ulcer and gastro-intestinal disorders. It is produced by baking the salt packed in bamboo cylinder nine times under the fire of pine tree. Three of commercially available bamboo salt products (bamboo salt A, B, and C) were characterized by qualitative and quantitative analyses using inductively coupled plasma (ICP) spectrometer, ion chromatograph (IC), X-ray diffractometer (XRD), and electron microscope (EM). Compared with crude salt, the contents of iron, silicon, potassium, and phosphate in the bamboo salt products were higher whereas the sulfate content was lower. Water-insoluble fraction of bamboo salts contained the following compounds; MgO, $SiO_2,\;Mg_2Si0_4,\;and\;CaMgSi0_4$. The study on the microscopic structures of the bamboo salts were shown to have smooth surface and fused shape compared with crude salt. Among the three bamboo salt products, product A was used to test a possible inhibitory effect on gastric acid secretion. Each test material (bamboo salt A, crude salt, and reagent-grade NaCl) was given orally to Sprague-Dawley rats at doses of 0.2, 1.0, and 2.0 g/kg for 28 days before pyrolus ligation. Twenty four hours after the last administration of the test materials, volume, pH, total acidity, and pepsin activity of gastric juice were measured by the Shay-ligation method. No significant differences were observed in the secretion of gastric acid between treated groups (bamboo salt-, crude salt- and reagent-grade NaCI-treated groups) and control group (distilled water-treated group). This result demonstrated that bamboo salt did not exert anti-ulcer activities in experimental animals used in the present study.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.2
• /
• pp.179-187
• /
• 2021

In the past five years, form construction, which accounts for approximately 25% of the total construction period, has continued to occur without a significant decrease in the number of deaths, with the largest proportion of collapse accidents. Accordingly, this study analyzed the difference in perception between the manager and worker by a questionnaire survey on the degree of risk and safety management level regarding a mold collapse accident. The survey was conducted in three groups: safety manager, field worker, and field manager. The results of the survey were analyzed by an independent sample T-Test using the SPSS program. As a result, there was almost no difference in recognition between managers, but a significant difference in recognition between managers and workers. In addition, there was a difference in management perception between the administrator and worker, which clearly shows the difference in the position between the administrator who manages and supervises hazardous disaster factors and the worker who works directly in the field. Such differences in perception can be a factor that cannot be mitigated. Based on this study, more developed research can narrow the perception gap between managers and workers and be used as a basic material for disaster research.

• Korean journal of food and cookery science
• /
• v.1 no.1
• /
• pp.74-81
• /
• 1985

For this research, the Atka-fisher which are used commonly in many homes for baking and broilling were broiled by an iron baking method, a pan baking method, a grill baking method and a microwave baking method respectively after 20 hours salting with 3% salt concentration of fish muscle weight. This thesis has an intention of appreciating the tastes according to each baking method through a sensory test, of examining the corelation between the change of texture measured by Rheometer and a sensory test and of comparing the changes of chemical component of the fish. The results were as follow: 1. The appearance of the broiled Atka-fish maintained a good appearance by the iron baking method and the grill baking method. In the color, the iron baking method and the grill baking method by direct :fire resulted a good score too. In the flavor, there was a significant difference between the grill baking method and the microwave baking method while there was no difference between the iron baking method and the pan baking method. The result of tenderness showed that the pan baking method has the highest score. Difference between the iron baking method and the pan baking was not significant. There was no difference in tenderness between the grill baking method and the microwave baking method. The iron baking method showed-the highest score in juciness and the microwave baking method stowed the highest score in acceptability however the differences were not significant. 2. As a result of the measurement of the texture by Rheometer, the iron baking method and the grill baking method showed higher score than other methods in hardness and chewiness. In springiness and cohesiveness, there was no significant difference among methods. As a result of the measurement of the texture by Rheometer, the corelation with a sensory test was considered to be low. 3. After broil, the cooking retention was the highest in the pan baking method and the moisture content was the highest in microwave baking method. Nitrogen content was the highest in the iron baking method. Fat content was the highest in the iron baking method, followed by the grill baking method, the pan baking method, and the microwave baking method. Free amino acid content was the highest in the iron baking method, followed by the grill baking method, the pan baking method and the micro-wave baking method.

• Journal of the Korea Institute of Building Construction
• /
• v.15 no.3
• /
• pp.265-271
• /
• 2015

This study is intended to produce a PC (Precast Concrete) member without a steam curing process in developing the high early strength concrete satisfying the condition of 10MPa in compressive strength at the age of 6 hours, and is intended to ensure economic feasibility by increasing the turnover rate of concrete form. Hence, high early strength cement with high $C_3S$ content and the hardening accelerator of powder type accelerating the hydration of $C_3S$ was used. And the properties of concrete were evaluated according to the hardening accelerator mixing ratio (0, 1.2, 1.6, 2.0). No big difference was found from the tests of both slump and air content. When 1.6 % or higher amounts of the hardening accelerator were mixed, the compressive strength of 10MPa was achieved at the age of 6 hours. From the test results of autogenous (drying) shrinkage and plastic shrinkage, it can be seen that there was a difference according to hydration reaction rate due to the addition of the hardening accelerator. However, it was shown that no problem arose with crack and durability. And it was shown that resistance to freezing-thawing, carbonation, and penetration were excellent.