• 한국자기학회지
• /
• 제18권1호
• /
• pp.43-47
• /
• 2008

[ $ZnO-Bi_2O_3-Al_2O_3-B_2O_3-SiO_2$ ] nano-glass를 sol-gel 법으로 제조 하였다. 평균 입자 크기는 60.3 nm였으며 매우 균일한 입도 분포를 가졌다. Nano-glass를 NiZnCu ferrite의 저온소성용 소결조제로 사용하였으며 NiZnCu ferrite에 nano-glass를 첨가한 후 $840{\sim}900^{\circ}C$에서 2시간 소결을 진행하였다. 소결성 및 자기적 특성에 대해 연구하였으며 밀도, 수축율, 초투자율, 품질계수, 및 포 화자화값을 측정하였다. nano-glass를 0.5 wt% 첨가하여 $900^{\circ}C$에서 소결한 토로이달 core 시편의 초투자율은 1 MHz에서 측정 시 193.3의 값을 가졌다. 초투자율과 포화자화값은 소결온도가 증가함에 따라 증가하는 경향을 나타내었다. sol-gel 법에 의해 제조된 $ZnO-Bi_2O_3-Al_2O_3-B_2O_3-SiO_2$ nano-glass를 칩인덕터용 NiZnCu ferrite의 저온 소결조제로 사용 가능함을 알 수 있었다.

• 한국전기전자재료학회논문지
• /
• 제20권10호
• /
• pp.873-877
• /
• 2007

In order to apply a complex multilayer chip LC filter, this study has estimated the interfacial reaction and coupling properties of dielectric materials $Pb(Fe_{1/2}Nb_{1/2})O_3$ and Ni-Zn-Cu ferrite materials through low-temperature co-sintering (LTCS). PFN powders were fabricated using double calcinated at $700^{\circ}C$ and then $850^{\circ}C$. While the perovskite phase rate was found to be 91 %, after heat treatment at $900^{\circ}C$ for 6h, the perovskite phase rate and density exhibited a value of 100 % and 7.46$g/cm^3$, respectively. The PFN/Ni-Zn-Cu ferrite, PFN/CUO (or $Pb_2Fe_2O_5$) and ferrite/CuO (or $Pb_2Fe_2O_5$) were mechanically coupled through interfacial reactions after the specimen was co-sintered at $900^{\circ}C$ for 6 h. No intermediate layer exists for the mutual coupling reaction. This result indicates the possibility of low-temperature co-sintering without any interfacial reaction layer for a multilayer chip LC filter.

• 한국세라믹학회지
• /
• 제50권3호
• /
• pp.231-237
• /
• 2013

Thermodynamic modeling of the $Ni_{0.5}Zn_{0.4}Cu_{0.1}Fe_2O_4$ complex ferrite system has been adopted as a rational approach to establish routes to better synthesis conditions for pure phase $Ni_{0.5}Zn_{0.4}Cu_{0.1}Fe_2O_4$ complex ferrite. Quantitative analysis of the different reaction equilibria involved in the precipitation of $Ni_{0.5}Zn_{0.4}Cu_{0.1}Fe_2O_4$ from aqueous solutions has been used to determine the optimum synthesis conditions. The spinel ferrites, such as magnetite and substitutes for magnetite, with the general formula $MFe_2O_4$, where M= $Fe^{2+}$, $Co^{2+}$, and $Ni^{2+}$ are prepared by coprecipitation of $Fe^{3+}$ and $M^{2+}$ ions with a stoichiometry of $M^{2+}/Fe^{3+}$= 0.5. The average particle size of the as synthesized $Ni_{0.5}Zn_{0.4}Cu_{0.1}Fe_2O_4$, measured by transmission electron microscopy (TEM), is 14.2 nm, with a standard deviation of 3.5 nm the size when calculated using X-ray diffraction (XRD) is 16 nm. When $Ni_{0.5}Zn_{0.4}Cu_{0.1}Fe_2O_4$ ferrite is annealed at elevated temperature, larger grains are formed by the necking and mass transport between the $Ni_{0.5}Zn_{0.4}Cu_{0.1}Fe_2O_4$ ferrite nanoparticles. Thus, the grain sizes of the $Ni_{0.5}Zn_{0.4}Cu_{0.1}Fe_2O_4$ gradually increase as heat treatment temperature increases. Based on the results of Thermogravimetric Analysis (TGA) and Differential Scanning Calorimeter (DSC) analysis, it is found that the hydroxyl groups on the surface of the as synthesized ferrite nanoparticles finally decompose to $Ni_{0.5}Zn_{0.4}Cu_{0.1}Fe_2O_4$ crystal with heat treatment. The results of XRD and TEM confirmed the nanoscale dimensions and spinel structure of the samples.

• 한국자기학회지
• /
• 제18권2호
• /
• pp.58-62
• /
• 2008

칩인덕터용 $Ni_{0.4}Zn_{0.4}Cu_{0.2}Fe_2O_4$ ferrite(NiZnCu ferrite)를 고상반응법 및 졸겔법으로 제조하였다. 고상반응법에 의해 제조된 마이크론크기의 NiZnCu ferrite 분말과 졸겔법에 의해 제조된 나노크기의 분말을 혼합하여 소결성 및 자기적 특성을 증가 시켰다. 나노크기의 분말을 20wt%첨가한 토로이달 코아 시편의 초투자율은 1 MHz에서 $880^{\circ}C$ 소결시 78.1에서 $920^{\circ}C$ 소결시 178.2의 값을 가졌으며 소결온도가 증가할수록 초투자율값이 증가하였다. 소결 밀도, 수축율 및 포화자화값도 소결온도가 증가함에 따라 증가하였으며 이것은 grain사이즈 효과 및 소결성이 증가 되었기 때문이다. 고상반응법에 의해 제조한 ferrite에 졸겔법에 의해 제조한 나노크기의 ferrite 분말을 혼합하여 소결성을 향상시키고 자기적 특성을 향상시킬 수 있었다.

• 한국세라믹학회지
• /
• 제29권5호
• /
• pp.383-390
• /
• 1992

We investigated the effect of substrate on the properties of the Ni-Zn-Cu ferrite thin films deposited on SiO2 (1000∼3000${\AA}$) / Si (100) substrate at various conditions by rf magnetron sputtering. A disktype Ni-Zn-Cu ferrite sintered by conventional ceramic process and argon gas were used as a target and a sputtering gas, repectively. The compositions of the thin films measured by EPMA were similar to target composition (Fe: 65.8 at%, Ni: 12.7 at%, Cu: 6.7 at%, Zn: 14.8 at%) irrespective of substrate temperature. Amorphous thin films were deposited when substrate was not intentionally heated, but the films came to crystallize with increasing substrate temperature, and crystalline thin films were deposited at substrate temperature above 200$^{\circ}C$. Below 250$^{\circ}C$ saturation magnetization (Ms), remanence (Mr) and coercivity (Hc) of the ferrite thin film increased with the substrate temperature due to the increase of grain size and the improvement of crystallinity. And above 250$^{\circ}C$, Ms, Mr increased slightly, but Hc of the amorphous thin films increased due to crystallization, whereas that of the crystalline thin films decreased because of grain growth and stress release.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 1997년도 춘계연구발표회 논문개요집
• /
• pp.98-99
• /
• 1997

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 1998년도 춘계연구발표회 논문개요집
• /
• pp.70-71
• /
• 1998

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1992년도 춘계학술발표회
• /
• pp.132-133
• /
• 1992

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 1994년도 추계연구발표회 논문개요집
• /
• pp.72-73
• /
• 1994

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2000년도 춘계연구발표회 논문개요집
• /
• pp.38-39
• /
• 2000