• Korean Journal of Environmental Agriculture
• /
• v.23 no.3
• /
• pp.170-177
• /
• 2004

Agroenvironmental characteristics in paddy fields irrigated with the water of Nagdong river were analyzed along the river watershed for two years from 1999. The sites monitored from upper reaches of the river were Andong, Sangju, Gumi, Goryeong, Changnyeong, Milyang and Pusan. In paddy soils, the contents of heavy metals such as Cd, Cr, Cu, Pb, Ni, Zn and As were around natural values showing the highest values in Pusan followed by Goryeong. In brown rice, the contents of heavy metals were lower than natural values. Soil chemical properties appeared higher values in the lower reaches including Goryeong than the upper ones. The highest parameters in Goryeong were pH ($5.9{\sim}6.1$), EC ($0.8{\sim}0.9\;dS/m$), $Av.P_2O_5$ ($155{\sim}201\;mg/kg$), exchangeable Ca ($6.7{\sim}7.4\;cmol^+/kg$), Mg ($1.92{\sim}2.50\;cmol^+/kg$), K ($0.18{\sim}0.21\;cmol^+/kg$) and those in Pusan were organic matter ($23.0{\sim}29.1\;g/kg$) and T-N ($1.6{\sim}1.8\;mg/kg$). In conclusion, the recommended rates of N fertilizer for rice cropping were 21.4%, 11.8% and 8.8% high for Andong, Sangju and Gumi, respectively and 14.9%, 4.6%, 4.5% and 11.5% low for Goryeong, Changnyeong, Milyang and Pusan, respectively reflecting the chemical properties of soils and the quality of irrigation water on the basis of 110 kgN/ha. In the case of phosphorous, the rates were 18.9% and 33.3% low for Changnyeong and others, respectively on the basis of $45\;kgP_2O_5/ha$. The populations of bacteria, fungi, actinomycetes, Bacillus, fluorescent Pseudomonas and Biomass C were high at the lower reaches including Goryeong, which showed relatively much nutrient contents of organic matter, total N and phosphorous etc.

• Economic and Environmental Geology
• /
• v.22 no.1
• /
• pp.35-63
• /
• 1989

Geochemical characteristics of the Guryongsan (Ogcheon) uraniferous black slate show that this is an analogue to the conventional Chattanooga and Alum shales in occurrences. Whereas, its highest enrichment ratio in metals including uranium, among others, is explained by the cyclic sedimentation of the black muds and quartz-rich silts, and the uniform depositional condition with some what higher pH condition compared to the conditions of the known occurrences. The cyclic sedimentation, caused by the periodic open and close of the silled basin, has brought about the flush-out) of the uranium depleted water and the recharge with the new metal-rich sea water, which consequently contributed to the high concentration of metals in mud. The metal-rich marine black muds, which mostly occur in the early to middle Palaeozoic times, is attributed by the geologic conditions which related to the atmospheric oxygen contents, and these are scarcely met in the late Precambrian and/or with the onset of Palaeozoic era in the geologic evolution of the earth.

• Korean Journal of Soil Science and Fertilizer
• /
• v.39 no.6
• /
• pp.339-344
• /
• 2006

A lot of organic wastes have been produced from diverse industries, they must be tested by the regulation of fertilizer control act if reuse the organic wastes for agricultural utilization. The regulation has had only two criteria; the content of organic matter and 8 heavy metals. This study was conducted to evaluation trace element (boron, cobalt, molybdenum, and selenium) and distribution of organic compounds with different classification for complement the regulation in 16 organic waste materials(62 samples) collected from different regions and industries. Contents of boron(leather industry sludge, $154.2mg\;kg^{-1}$; food company sludge, $57.1mg\;kg^{-1}$), cobalt(industrial area sewage sludge, $95.2mg\;kg^{-1}$; metropolitan sewage sludge, $22.9mg\;kg^{-1}$), molybdenum(metropolitan sewage sludge, $40.1mg\;kg^{-1}$; food company sludge, $16.8mg\;kg^{-1}$), selenium (fiber industry sludge, $28.1mg\;kg^{-1}$; leather industry sludge, $16.9mg\;kg^{-1}$; food company sludge, $15.9mg\;kg^{-1}$) were highest compare to the other organic wastes. Total PAHs contents were the highest in paper-mill manufacture($3,462ug\;kg^{-1}$), and among the 16 PAHs, naphthalene, phenanthrene, pyrene, fluoroanthene, Anthracene and acenaphthene were detected more clearly than others in all kinds of organic resources.

• Korean Journal of Environmental Agriculture
• /
• v.32 no.4
• /
• pp.348-354
• /
• 2013

BACKGROUND: Globally, concern about emerging infectious diseases of livestock is growing. For the disposal of the animal carcass, it is necessary to recycle the carcass into an agriculturally usable product. The objective of this study was to investigate the composting conditions of liquid by-product obtained from degradation of animal carcass. METHODS AND RESULTS: Optimum conditions of liquid fertilizer were investigated using different microorganisms, pHs, and volumes of microorganisms (Lactobacillus rhamnosus+Pichia deserticola). Based on the results from the optimum conditions, compost maturity and quality of liquid fertilizer were evaluated for 112 days. The compost maturity of liquid fertilizer were higher in the order of LP(Lactobacillus rhamnosus + Pichia deserticola) > BC(Bacillus cereus) > BS(Bacillus subtilis). The optimum condition under different volumes of LP was injection of 0.5 mL/100 mL. The compost maturity under different pHs were higher in the order of pH 7 > $$5{\geq_-}9{\frac{._-}{.}}11$$. The liquid by-product at 56 days after composting was completely decomposed. The concentrations of T-N, T-P and $K_2O$ in liquid fertilizer at 56 days were 0.94, 0.17 and 3.78%, respectively, and the sum of those concentrations was 4.89%. CONCLUSION(S): Liquid fertilizer of by-product using pig carcass was decomposed with optimum conditions(LP, pH 7, injection of 0.5 mL/100 mL) in 56 days after composting, and was suitable for official standard of commercial fertilizer.

• Journal of Food Hygiene and Safety
• /
• v.26 no.3
• /
• pp.273-282
• /
• 2011

This study established hazards which may cause risk to human at farm during cultivation stage of paprika. Samples of plants (paprika, leaf, stem), cultivation environments (water, soil), personal hygiene (hand, glove, clothes), work utensils (carpet, basket, box) and airborne bacteria were collected from three paprika farms (A, B, C) located in Western Gyeongnam, Korea. The collected samples were assessed for biological (sanitary indications and major foodborne pathogens), chemical (heavy metals, pesticide residues) and physical hazards. In biological hazards, total bacteria and coliform were detected at the levels of 1.9~6.6 and 0.0~4.610g CFU/g, leaf, mL, hand or 100 $cm^2$, while Escherichia coli was not detected in all samples. In major pathogens, only Bacillus cereus were detected at levels of ${\leq}$ 1.5 log CFU/g, mL, hand or 100 $cm^2$, while Staphylococuus aureus, Listeria monocytogenes, E. coli O157 and Salmonella spp. were not detected in all samples. Heavy metal and pesticide residue as chemical hazards were detected at levels below the regulation limit, physical hazard factors, such as insects, pieces of metal and glasses, were also found in paprika farms. Proper management is needed to prevent biological hazards due to cross-contamination while physical and chemical hazards were appropriate GAP criteria.

• Journal of Food Hygiene and Safety
• /
• v.27 no.2
• /
• pp.152-160
• /
• 2012

The objective of this study was to analyze hazards for the growing stage of 6 tomato farms (A, B, C; soli farms, D, E, F; Nutriculture farms) located in Gyeongsangnam-do to establish the good agricultural practices (GAP). A total of 144 samples for analyzing hazards collected from cultivation environments (irrigation water, soil, nutrient solution, and air) and personal hygiene (hands, gloves, and cloths) were assessed for biological (sanitary indications and major food borne pathogens) and chemical hazards (heavy metals). Total bacteria, coliform, and fungi were detected at levels of 0.2-7.2, 0.0-6.1, and 0.0-5.4 log CFU/g, mL, hand or 100 $cm^2$, respectively. Escherichia coli were only detected in the soil sample from B farm. In case of pathogens, Bacillus cereus was detected at levels of 0.0-4.4 log CFU/(g, mL, hand or 100 $cm^2$), whereas Staphylococuus aureus, Listeria monocytogenes, E. coli O157, and Salmonella spp. were not detected in all samples. Heavy metals as a chemical hazard were detected in soil and irrigation water, but levels of them were lower than the permit limit. In conclusion, chemical hazard levels complied with GAP criteria, but biological hazards at the growing stage of tomato farms were confirmed. Therefore a proper management to prevent microbial contamination is needed.

• Proceedings of the Korean Environmental Sciences Society Conference
• /
• 1998.10a
• /
• pp.2-4
• /
• 1998

Proliferation of Nocardia amarae cells in activated sludge has often been associated with the generation of nuisance foams. Despite intense research activities in recent years to examine the causes and control of Nocardia foaming in activated sludge, the foaming continued to persist throughout the activated sludge treatment plants in United States. In addition to causing various operational problems to treatment processes, the presence of Nocardia may have secondary effects on the fate of heavy metals that are not well known. For example, for treatment plants facing more stringent metal removal requirements, potential metal removal by Nocardia cells in foaming activated sludge would be a welcome secondary effect. In contrast, with new viosolid disposal regulations in place (Code o( Federal Regulation No. 503), higher concentration of metals in biosolids from foaming activated sludge could create management problems. The goal of this research was to investigate the metal sorption property of Nocardia amarae cells grown in batch reactors and in chemostat reactors. Specific surface area and metal sorption characteristics of N. amarae cells harvested at various growth stages were compared. Three metals examined in this study were copper, cadmium and nickel. Nocardia amarae strain (SRWTP isolate) used in this study was obtained from the University of California at Berkeley. The pure culture was grown in 4L batch reactor containing mineral salt medium with sodium acetate as the sole carbon source. In order to quantify the sorption of heavy metal ions to N amarae cell surfaces, cells from the batch reactor were harvested, washed, and suspended in 30mL centrifuge tubes. Metal sorption studies were conducted at pH 7.0 and ionlc strength of 10-2M. The sorption Isotherm showed that the cells harvested from the stationary and endogenous growth phase exhibited significantly higher metal sorption capacity than the cells from the exponential phase. The sequence of preferential uptake of metals by N. amarae cells was Cu>Cd>Ni. The specific surFace area of Nocardia cells was determined by a dye adsorption method. N.amarae cells growing at ewponential phase had significantly less specific surface area than that of stationary phase, indicating that the lower metal sorption capacity of Nocardia cells growing at exponential phase may be due to the lower specific surface area. The growth conditions of Nocardia cells in continuous culture affect their cell surface properties, thereby governing the adsorption capacity of heavy metal. The comparison of dye sorption isotherms for Nocardia cells growing at various growth rates revealed that the cell surface area increased with increasing sludge age, indicating that the cell surface area is highly dependent on the steady-state growth rate. The highest specific surface area of 199m21g was obtained from N.amarae cell harvested at 0.33 day-1 of growth rate. This result suggests that growth condition not only alters the structure of Nocardia cell wall but also affects the surface area, thus yielding more binding sites of metal removal. After reaching the steady-state condition at dilution rate, metal adsorption isotherms were used to determine the equilibrium distributions of metals between aqueous and Nocardia cell surfaces. The metal sorption capacity of Nocardia biomass harvested from 0.33 day-1 of growth rate was significantly higher than that of cells harvested from 0.5- and 1-day-1 operation, indicatng that N.amarae cells with a lower growth rate have higher sorpion capacity. This result was in close agreement with the trend observed from the batch study. To evaluate the effect of Nocardia cells on the metal binding capacity of activated sludge, specific surface area and metal sorption capacity of the mixture of Nocardia pure cultures and activated sludge biomass were determined by a series of batch experiments. The higher levels of Nocardia cells in the Nocardia-activated sludge samples resulted in the higher specific surface area, explaining the higher metal sorption sites by the mixed luquor samples containing greater amounts on Nocardia cells. The effect of Nocardia cells on the metal sorption capacity of activated sludge was evaluated by spiking an activated sludge sample with various amounts of pre culture Nocardia cells. The results of the Langmuir isotherm model fitted to the metal sorption by various mixtures of Nocardia and activated sludge indicated that the mixture containing higher Nocardia levels had higher metal adsorption capacity than the mixture containing lower Nocardia levels. At Nocardia levels above 100mg/g VSS, the metal sorption capacity of activate sludge increased proportionally with the amount of Noeardia cells present in the mixed liquor, indicating that the presence of Nocardia may increase the viosorption capacity of activated sludge.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.476-476
• /
• 2014

서론: 저 전력 소모를 필요로 하는 무선 센서 네트워크 관련 기술의 급격한 발달과 함께 자체 전력 수급을 위한 진동 에너지 수확 기술에 대한 연구가 활발히 이루어지고 있다. 다양한 구조와 소재를 압전 외팔보에 적용하여 제안하고 있다. 그 중에서도 진동 기반의 에너지 수확 소자는 주변 환경에서 쉽게 진동을 얻을 수 있고, 높은 에너지 밀도와 제작 방법이 간단하다는 장점을 가지고 있어 많은 분야에 응용 및 적용 가능하다. 기존 연구에서는 2차원적으로 진동 에너지 수확을 위한 휜 구조의 압전 외팔보를 제안 하였다. 휜 구조를 갖는 압전 외팔보는 각각의 짧은 두 개의 평평한 외팔보가 일렬로 연결된 것으로 볼 수 있다. 하나의 짧고 평평한 외팔보는 진동이 가해지면 접선 방향으로 응력이 생겨 최대 휨 모멘텀을 갖게 된다. 그러므로 휜 구조를 갖는 외팔보는 진동이 인가됨에 따라 길이 방향과 수직 방향으로 진동한다. 하지만, 이 구조는 수평 방향으로 가해지는 진동에 대한 에너지를 수확하기에는 한계점을 가진다. 즉, 3축 방향에서 임의의 방향에서 진동 에너지를 수확하기는 어렵다. 본 연구에서는 3축 방향에서 에너지를 효율적으로 수확할 수 있도록 헤어-셀 구조의 압전 외팔보 에너지 수확소자를 제안한다. 제안된 소자는 길이 방향과 수직 방향뿐만 아니라 수평 방향으로도 진동하여 임의의 방향에서 진동 에너지를 수확할 수 있다. 구성 및 공정: 제안하는 소자는 3축 방향에서 임의의 진동을 수확하기 위해서 길이를 길게 늘이고 길이 방향을 따라 휘어지는 구조의 헤어-셀 구조로 제작하였다. 외팔보의 구조는 외팔보의 폭 대비 길이의 비가 충분히 클 때, 추가적인 자유도를 얻을 수 있다. 그러므로 헤어-셀 구조의 에너지 수확 소자는 기본적인 길이 방향, 수직방향 그리고 수평방향에 더불어 추가적으로 뒤틀리는 방향을 통해서 3차원적으로 임의의 주변 진동 에너지를 수확하여 전기적인 에너지로 생성시킬 수 있다. 제작된 소자는 높은 종횡비를 갖는 무게 추($500{\times}15{\times}22{\mu}m3$)와 길이 방향으로 길게 휜 압전 외팔보($1000{\times}15{\times}1.7{\mu}m3$)로 구성되어있다. 공정 과정은 다음과 같다. 먼저, 실리콘 웨이퍼 위에 탄성층을 형성하기 위해 LPCVD SiNx를 $0.8{\mu}m$와 LTO $0.2{\mu}m$를 증착 후, 각각 $0.03{\mu}m$과 $0.12{\mu}m$의 두께를 갖는 Ti와 Pt을 하부 전극으로 스퍼터링한다. 그리고 Pb(Zr0.52Ti0.48)O3 박막을 $0.35{\mu}m$ 두께로 졸겔법을 이용하여 증착하고 상부 Pt층을 두께 $0.1{\mu}m$로 순차적으로 스퍼터링하여 형성한다. 상/하부 전극은 ICP(Inductively Coupled Plasma)를 이용해 건식 식각으로 패턴을 형성한다. PZT 층과 무게 추 사이의 보호막을 씌우기 위해 $0.2{\mu}m$의 Si3N4 박막이 PECVD 공정법으로 증착되고, RIE로 패턴을 형성된다. Ti/Au ($0.03/0.35{\mu}m$)이 E-beam으로 증착되고 lift-off를 통해서 패턴을 형성함으로써 전극 본딩을 위한 패드를 만든다. 초반에 형성한 실리콘 웨이퍼 위의 SiNx/LTO 층은 RIE로 외팔보 구조를 형성한다. 이후에 진행될 도금 공정을 위해서 희생층으로는 감광액이 사용되고, 씨드층으로는 Ti/Cu ($0.03/0.15{\mu}m$) 박막이 스퍼터링 된다. 도금 형성층을 위해 감광액을 패턴화하고, Ni0.8Fe0.2 ($22{\mu}m$)층으로 도금함으로써 외팔보 끝에 무게 추를 만든다. 마지막으로, 압전 외팔보 소자는 XeF2 식각법을 통해 제작된다. 제작된 소자는 소자의 여러 층 사이의 고유한 응력 차에 의해 휨 변형이 생긴다. 실험 방법 및 측정 결과: 제작된 소자의 성능을 확인하기 위하여 일정한 가속도 50 m/s2로 3축 방향에 따라 입력 주파수를 변화시키면서 출력 전압을 측정하였다. 먼저, 소자의 기본적인 공진 주파수를 얻기 위하여 수직 방향으로 진동을 인가하여 주파수를 변화시켰다. 그 때에 공진 주파수는 116 Hz를 가지며, 최대 출력 전압은 15 mV로 측정되었다. 3축 방향에서 진동 에너지 수확이 가능하다는 것을 확인하기 위하여 제작된 소자를 길이 방향과 수평 방향으로 가진기에 장착한 후, 기본 공진 주파수에서의 출력 전압을 측정하였다. 진동이 길이방향으로 가해졌을 때에는 33 mV, 수평방향으로 진동이 인가되는 경우에는 10 mV의 최대 출력 전압을 갖는다. 제안하는 소자가 수 mV의 적은 전압은 출력해내더라도 소자는 진동이 인가되는 각도에 영향 받지 않고, 3축 방향에서 진동 에너지를 수확하여 전기에너지로 얻을 수 있다. 결론: 제안된 소자는 3축 방향에서 진동 에너지를 수확할 수 있는 에너지 수확 소자를 제안하였다. 외팔보의 구조를 헤어-셀 구조로 길고 휘어지게 제작함으로써 기본적인 길이 방향, 수직방향 그리고 수평방향에 더불어 추가적으로 뒤틀리는 방향에서 출력 전압을 얻을 수 있다. 미소 전력원으로 실용적인 사용을 위해서 무게추가 더 무거워지고, PZT 박막이 더 두꺼워진다면 소자의 성능이 향상되어 높은 출력 전압을 얻을 수 있을 것이라 기대한다.

• Economic and Environmental Geology
• /
• v.42 no.2
• /
• pp.121-131
• /
• 2009

The distribution characteristics of heavy metals for surface sediments in east oceanic dumping area (EDA) and west oceanic dumping area (WDA) are evaluated by grain sizes, minerals, sedimentation rates and compositions of heavy metals. The mean grain sizes in EDA and WDA range from $7.95{\Phi}$ to $8.51{\Phi}$ and $7.42{\Phi}$ to $8.15{\Phi}$, respectively. These are mostly belonging to the M (mud) type. Minerals in the surface sediments consist of illite with chlorite, smectite, and kaolinite. Sedimentation rates estimated by $^{210}Pb$ method in EDA and WDA are 1.11 mm/yr$\sim$1.73 mm/yr and 1.87 mm/yr, respectively. According to the interrelationship, concentrations of Ni, Cu, Cr, and Zn are closely associated with mean grain size, Al, and Fe, whereas concentrations of Cd and Pb are poorly associated with ones. The enrichment factors of these elements are higher than 1.5, suggesting that the concentrations of Cd and Pb in the surface sediments are affected by anthropogenic sources. The $I_{geo}$-class numbers of Cd and Pb in the surface sediments are mostly classified in 2 to 4, showing moderate to strongly polluted. These numbers in EDA are higher than that of WDA, and the highest number is 4, indicative of the strongly polluted class. Our results show that the disposed wastes at EDA include mineralogical wastes, dredged materials from sewage disposals, and sludges from constructions having materials of WDA. The annual amount of oceanic dumping in EDA is double than that in WDA.

• Journal of Aquaculture
• /
• v.13 no.2
• /
• pp.169-174
• /
• 2000

Reproductive cycle of U. unicinctus was studied from September 1998 to August 1999, using gonadosomatic index (CSI) as an indicator. In November, the CSI values were maximum for male (6.2) and female (7.0), respectively; the values were lowest for them (1.0 and 0.5) during the successive february. Subsequently, they rapidly increased and attained peak by March-April. The values decreased again in both sexes and remained unchanged until August. The index increased in October to attain the peak by November. The CSI values clearly indicated that there are two spawning events in a year, namely the first one during April-May and the second one in December. Reproductive cycle was classified into the following successive stages: in female, multipication (January~February, June ~Setember), maturation (March~April, November), spent (May and December), degeneration and resting (June and January), and in male, multiplication January ~ february, June ~September), maturation (March~April, October~November), spent (May and December) and degeneration and resting (January and June). Histological observations revealed that oocytes in the ovary matured simultaneously in November and March. At the same time, the envelopes of matured testis became thinner than those in the early stage.