• Journal of Powder Materials
• /
• v.16 no.4
• /
• pp.268-274
• /
• 2009

For the purpose of obtaining basic information on the development of lead-free materials, a high density composites (a) W-Cu, (b) W-Sn (c)W-Cu-Sn and (d) W-Cu-Ni were fabricated by the P/M method. The particle size of used metal powders were under 325 mesh, inner size of compaction mould was $\phi8$ mm, and compaction pressure was 400 MPa. A High density composite samples were sintered at a temperature between $140^{\circ}C$ and $1050^{\circ}C$ for 1 hour under Ar atmosphere. The microstructure, phase transformation and physical properties of the sintered samples were investigated. As the results, the highest relative density of 95.86% (10.87 g/$cm^3$) was obtained particularly in the sintered W-Cu-Sn ternary system sample sintered at 450 for 1hr. And, Rockwell hardness (HRB) of 70.0 was obtained in this system.

• Journal of the Korean institute of surface engineering
• /
• v.44 no.6
• /
• pp.250-254
• /
• 2011

NiO-AZO films were deposited on glass substrate by DC and RF magnetron co-sputtering system in pure $O_2$ gas without substrate heating during deposition. In order to control the chemical composition of the film, NiO target was supplied with constant RF power of 150 W and AZO target (doped with 2.98 at% aluminum) with DC power varied between 40 W to 80 W. Deposited NiO-AZO films were evaluated by structural and chemical analysis. With introducing AZO, XRD and XPS data reveal that NiO were supplied with more oxygen. these results could be strongly affected by the higher bond enthalpy of NiO compared to ZnO, which makes it possible for NiO to obtain excessive oxygen from ZnO.

• Corrosion Science and Technology
• /
• v.11 no.6
• /
• pp.275-279
• /
• 2012

Ni-W alloy deposits have lately attracted the interest as an alternative surface treatment method for hard chromium electrodeposits because of higher wear resistance, hardness at high temperature, and corrosion resistance. This study deals with influences of process variables, such as electodeposition current density, plating temperature and pH, on the internal stress of Ni-W nanocrystalline deposits. The internal stress was increased with increasing the applied current density. With increasing applied current density, the grain size of the deposit decreases and concentration of hydrogen in the deposit increases. The subsequent release of the hydrogen results in shrinkage of the deposit and the introduction of tensile stress in the deposit. Consequently, for layers deposited at high current density, cracking occurs readily owing to high tensile stress value. By increasing the temperature of the electrodeposition from $60^{\circ}C$ to $80^{\circ}C$, the internal stress was decreased. It seems that an increase in the number of active ions overcoming the activation energy at elevated temperature caused a decline in the concentration polarization and surface diffusion. It decreased the level of hydrogen absorption due to the lessened hydrogen evolution reaction. Therefore, the lower level of hydrogen absorption degenerated the hydride on the surface of the electrode, resulting in the reduction of the internal stress of the deposits. By increasing the pH of the electrodeposition from 5.6 to 6.8, the internal stress in the deposits were slightly decreased. It is considered that the decrease in internal stess of deposits was due to supply of W complex compound in cathode surface, and hydrogen ion resulted from decrease of activity.

• Journal of the Korean Ceramic Society
• /
• v.51 no.4
• /
• pp.243-247
• /
• 2014

Spherical NiO-YSZ particles were synthesized by ultrasonic spray pyrolysis (USP). The morphology of the synthesized particles can be modified by controlling parameters such as precursor pH, carrier-gas flow-rate, and temperature of the heating zone. The synthesized spherical NiO-YSZ particles have rough surface morphology at high carrier-gas flow-rates due to rapid gas exhaustion and insufficient particle ordering. The Ni-YSZ cermet anode synthesized by ultrasonic spray pyrolysis at a flow rate of l L/min, with precursor solution at pH4, showed a higher maximum power density of 256 $mW/cm^2$ compared to a conventionally mixed Ni-YSZ anode (185 $mW/cm^2$) at $800^{\circ}C$. While the area-specific resistance of conventionally mixed Ni-YSZ anodes increases gradually with operation time (indicating performance degradation), the Ni-YSZ anode synthesized by USP does not exhibit any performance degradation, even after 500 h.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1993.11a
• /
• pp.45-45
• /
• 1993

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2007.11a
• /
• pp.124.2-124.2
• /
• 2007

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 1997.04a
• /
• pp.34-34
• /
• 1997

The effect of alloying mode and porosity on the axial tension-tension fatigue behavior of a P/M steel of nominal composition Fe-4w/o Ni-1.5w/o Cu-O.5w/o Mo-O.5w/o C has been evaluated. Alloying modes utilized were elemental powder mixing, partial alloying(distaloy) and prealloying by water atomization; in each case the carbon was introduced as graphite prior to sintering. Powder compacts were sintered($1120{\circ}C$/30 min.) in 7Sv/o $H_2$/25v/o $N_2$ to densities in the range 6.77-7.2 g/$cm^3$. The dependence of fatigue limit response on alloying mode and porosity was interpreted in terms of the constituent phases and the pore and fracture morphologies associated with the three alloying modes. For the same nominal composition, the three alloying modes resulted in different sintered microstructures. In the elemental mix alloy and the distaloy, the major constituent was coarse and fine pearlite, with regions of Ni-rich ferrite, Ni-rich martensite and Ni-rich areas. In contrast, the prealloy consisted primarily of martensite by with some Ni-rich areas. From an examination of the fracture surfaces following fatigue testing it was concluded that essentially all of the fracture surfaces exhibited dimpled rupture, characteristic of tensile overload. Thus, the extent of growth of any fatigue cracks prior to overload was small. The stress amplitude for the three alloying modes at 2x$l0^6$ was used for the comparison of fatigue strengths. For load cycles <3x$l0^5$, the prealloy exhibited optimum fatigue response followed by the distaloy and elemental mix alloy, respectively. At load cycles >2x$l0^6$, similar fatigue limits were exhibited by the three alloys. It was concluded that fatigue cracks propagate primarily through pores, rather than through the constituent phases of the microstructure. A decrease in pore SIze improved the S-N behavior of the sintered steel.

• Journal of Radiation Industry
• /
• v.9 no.4
• /
• pp.167-170
• /
• 2015

Radioisotope (Nuclear) battery using $^{63}Ni$ was prepared as beta cell. The electroplated $^{63}Ni$ on Ni foil is fabricated, and beta cell and photovoltaic hybrid battery was designed to use at both day and night in space project. A Ni-plating solution is prepared by dissolving metal particles including $^{62}Ni$ and $^{63}Ni$ from neutron irradiation of ($n,{\gamma}$). Electroplating solution of a chloride bath consists on nickel ions in HCl, $H_3BO_3$, and KOH. The deposition was carried out at current density of $10mA\;cm^{-2}$. The prepared beta source was attached on a PN junction and measured I-V properties. The power output at activity of 0.07 mCi and 0.45 mCi were 0.55 pW and 2.69 nW, respectively.

• Journal of Electrochemical Science and Technology
• /
• v.13 no.4
• /
• pp.424-430
• /
• 2022

In the study, Ni²⁺ (nickel) removal from synthetically prepared wastewater by electrocoagulation method, which is one of the electrochemical treatment processes, was investigated and parameters such as current density, pH, mixing speed, initial Ni²⁺ concentration, supporting electrolyte type and concentration were determined to determine Ni²⁺ removal efficiencies effects were studied. Experiment conditions during 30 minutes of electrolysis; the current density was determined as 0.95 mA/cm², the initial pH of the wastewater was 6, the mixing speed was 150 rpm, and the initial nickel concentration was 250 mg/L. The Ni²⁺ removal efficiency was obtained as 75.99% under the determined experimental conditions, while the energy consumption was calculated as 3.15 kW-h/m³. In the experiments, it was observed that the type and concentration of the supporting electrolyte did not have a significant effect on the Ni²⁺ removal efficiency. In the trials where the effect of the support electrolyte concentration was examined, the Ni²⁺ removal efficiency was 75.99% in the wastewater environment without the supporting electrolyte, while the Ni²⁺ removal efficiency was 81.55% when 7.5 mmol/L NaCl was used after the 30-minute reaction, and the energy consumption was 2.15 kW-h/m³ obtained as. As a result of the studies, it was concluded that the electrocoagulation process can be applied in the treatment of wastewater containing Ni²⁺.

• New & Renewable Energy
• /
• v.4 no.1
• /
• pp.11-18
• /
• 2008

In-situ lithiated NiO has been manufactured as a conventional cathode material of molten carbonate fuel cell (MCFC), however this material has a weakness for commercialization of MCFC because NiO is spontaneously dissolved into the electrolyte under MCFC operating conditions, resulting in short circuit between cathode and anode. In this research, therefore, $Co(OH)_2$-coated Ni powder was prepared by precipitation method with controlling pH at low temperature and atmospheric pressure. Modified cathode was fabricated by a conventional tape casting method and sintered at 700$^{\circ}C$ in a $H_2/N_2$ atmosphere, Based on characterization result, Pore size distribution and porosity was suitable for the cathode of MCFC. According to the result of dissolution, Ni solubility of modified cathode was 33% lower than that of conventional cathode. In addition, modified electrode showed a good performance from the single cell operation.