• Journal of the Korean Ceramic Society
• /
• v.42 no.7 s.278
• /
• pp.509-515
• /
• 2005

Interfacial reactions at LSGM electrolyte and NiO-GDC anode interfaces were thoroughly investigated with Environmental Scanning Electron Microscopy (ESEM-PHlLIPS XL-30) and Energy Dispersive X-ray (EDX-Link XL30). According to the analysis, serious reaction zone was observed at LSGM/NiO-GDC interface. It was found that the reaction layer was originated from the chemical reaction between NiO and LSGM. The reaction products were identified as La deficient form of LSGM based perovskite and Ni-La-O compounds such as LaSrGa$_{3}$O$_{7}$ and LaNiO$_{3}$ from the X-Ray Diffraction (XRD, Philips) analysis. According to the electrical characterization, interfacial layer was very electrically resistive which would be the cause of high internal resistance and low power generating characteristic of the unit cell.

• Transactions of the Korean hydrogen and new energy society
• /
• v.24 no.3
• /
• pp.230-236
• /
• 2013

In this study, successive coating and co-sintering techniques have been used to fabricate LSM/GDC based cathode supported direct carbon fuel cells. The porous LSM/GDC cathode substrate, dense, thin and crack free GDC and ScSZ layers as bi-layer electrolyte, and a porous Ni/ScSZ anode layer was obtained by co-firing at $1400^{\circ}C$. The porous structure of LSM/GDC cathode substrate, after sintering at $1400^{\circ}C$, was obtained due to the presence of GDC phase, which inhibits sintering of LSM because of its higher sintering temperature. The electrochemical characterization of assembled cell was carried out with air as an oxidant and carbon particles in molten carbonate as fuel. The measured open circuit voltages (OCVs) were obtained to be more than 0.99 V, independent of testing temperature. The peak power densities were 116, 195 and $225mWcm^{-2}$ at 750, 800 and $850^{\circ}C$, respectively.

• Journal of the Korean Ceramic Society
• /
• v.53 no.5
• /
• pp.494-499
• /
• 2016

In this work, the effects of different sintering inhibitors added to $La_{0.8}Sr_{0.2}MnO_{3-{\partial}}$ (LSM) were studied to obtain an optimum cathode material for cathode-supported type of Solid oxide fuel cell (SOFC) in terms of phase stability, mechanical strength, electric conductivity and porosity. Four different sintering inhibitors of $Al_2O_3$, $CeO_2$, NiO and gadolinium doped ceria (GDC) were mixed with LSM powder, sintered at $1300^{\circ}C$ and then they were evaluated. The phase stability, sintering behavior, electrical conductivity, mechanical strength and microstructure were evaluated in order to assess the performance of the mixture powder as cathode support material. It has been found that the addition of $Al_2O_3$ undesirably decreased the electrical conductivity of LSM; other sintering inhibitors, however, showed sufficient levels of electrical conductivity. GDC and NiO addition showed a promising increase in mechanical strength of the LSM material, which is one of the basic requirements in cathode-supported designs of fuel cells. However, NiO showed a high reactivity with LSM during high temperature ($1300^{\circ}C$) sintering. So, this study concluded that GDC is a potential candidate for use as a sintering inhibitor for high temperature sintering of cathode materials.

• Journal of the Korean Ceramic Society
• /
• v.52 no.5
• /
• pp.338-343
• /
• 2015

To prevent an interfacial reaction between the anode and the electrolyte layer during the conventional high-temperature co-firing process, an anode-supported type cell with a thin-film electrolyte was fabricated by low-temperature ceramic thick film coating process. Ni-GDC cermet composite was used as the anode material and YSZ was used as the electrolyte material. Open circuit voltage and maximum power density were found to strongly depend on the surface uniformity of the anode functional layer. By optimizing the microstructure of the anode functional layer, the open circuit voltage and maximum powder density of the cell increased to 1.11 V and $1.35W/cm^2$, respectively, at $750^{\circ}C$. When a GDC barrier layer was applied between the YSZ electrolyte and the LSCF cathode, the cell showed good stability, with almost no degradation up to 100 h. Anode-supported type SOFCs with high performance and good stability were fabricated using a coating process.

• Journal of the Korean Ceramic Society
• /
• v.43 no.12 s.295
• /
• pp.798-804
• /
• 2006

Co-planar type single chamber solid oxide fuel cell with patterned electrode on a surface of electrolyte has been fabricated by robo-dispensing method and microfluidic lithography. The cells were composed of NiO-GDC-Pd or NiO-SDC cermet anode, $(La_{0.7}Sr_{0.3})_{0.95}MnO_3$ cathode, and yttria stablized zirconia electrolyte. The cell performance at $900^{\circ}C$ was investigated as a function of electrode geometries, such as anode-to-cathode distance, numbers of electrode pairs. Relationship between OCV and I-V characteristics at the optimized operation condition was also studied by DC source meter under the mixed gas condition of methane, air, and nitrogen. An increase of anode-facing-cathode area leads to lower OCV due to intermixing between product gases of anode and cathode, which in turn decreases the oxygen partial pressure difference.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.83.1-83.1
• /
• 2011

고체산화물 연료전지는 전해질의 양쪽에 cathode층과 anode층으로 구성되어 있다. 이러한 셀을 제작하기 위한 구성소재 코팅법으로는 EVD, CVD, sputter등의 기상공정과 screen printing, tape casting, dip coating등의 습식공정이 있다. 이중 현재 가장 널리 사용되고 있는 screen printing법은 코팅기판의 크기와 형태에 제한을 받아 원통형, 평관형에는 적용이 어렵다. 이러한 문제점을 해결하기 위해 본 연구에서는 electrolyte 지지체 위에 전사법을 통해 연료극(NiO-YSZ), 공기극(LSCF-GDC) 코팅층의 두께 및 형상을 제어할 수 있었으며 button cell을 제작하여 실제 SOFC에 적용이 가능함을 확인하였다.