• Journal of Environmental Science International
• /
• v.28 no.1
• /
• pp.65-73
• /
• 2019

The catalytic activity of Ni-0.2%YSZ (Yttria-Stabilized Zirconia) with different promoters was evaluated for $CO_2$ methanation. The catalysts were weighed for mixing and they were dried at $110^{\circ}C$ for molding into disks. The concentration of $CO_2$ and $CH_4$ for conducting of $CO_2$ methanation were analyzed by gas chromatography and the physical characteristics of the disk-type catalyst formed were analyzed by X-ray diffraction, scanning electron microscope and energy dispersive x-ray spectrometer. The addition of $CeO_2$ as a promoter for Ni-0.2%YSZ (denoted as Ni-5%Ce-0.2%YSZ) resulted in the highest $CO_2$ methanation. It also showed catalytic activity at a low temperature($200^{\circ}C$). Following this, $ZrO_2$, $SiO_2$, $Al_2O_3$ and $TiO_2$ were added to Ni-5%Ce-0.2%YSZ to compare the $CO_2$ methanation, and the highest efficiency was found for. Ni-1%Ti-5%Ce-0.2%YSZ Then, the concentration of Ti was increased to 10% and the catalytic activity was estimated using seven different types of commercial $TiO_2$. In conclusion, ST-01 $TiO_2$ showed the highest efficiency for $CO_2$ methanation.

• Transactions of the Korean hydrogen and new energy society
• /
• v.22 no.5
• /
• pp.592-598
• /
• 2011

Electrode of solid oxide fuel cell must have sufficient porosity to allow gas transport to the interface with electrolyte effectively but high porosity has a negative impact on structural stability in electrode support. Thus, the upper limit of porosity is based on consideration of mechanical strength of electrode. In this study, the effect of microstructure of Ni-YSZ anode supported SOFC on the mechanical and electrical property was investigated. LSCF composite cathode and 8YSZ electrolyte were used. The porosity of the anode was modified by the amount of graphite powder and added graphite contents were 24, 18, 12 vol%, respectively. The higher the porosity, the better the electrical performance, $P_{max}$. While the flexural strength decreased with increasing the amount of graphite. But the rate of increase in electrical performance and the rate of decrease in mechanical strength were not directly proportional to amount of graphite. The optimum graphite content incorporating both electrical and mechanical performance was 18 vol%.

• Journal of the Korean Ceramic Society
• /
• v.52 no.5
• /
• pp.315-319
• /
• 2015

Yttria-stabilized zirconia (YSZ)-based micro tubular SOFC single cells were fabricated by electrophoretic deposition (EPD) process. Stable slurries for the EPD process were prepared by adding phosphate ester (PE) as a dispersant in order to control the pH, conductivity, and zeta-potential. NiO-YSZ anode support, NiO-YSZ anode functional layer (AFL), and YSZ electrolyte were consecutively deposited on a graphite rod using the EPD process; materials were then co-sintered at $1400^{\circ}C$ for 4 h. The thickness of the deposited layer increased with increasing of the applied voltage and the deposition time. A YSZ-based micro tubular single cell fabricated by the EPD process exhibited a maximum power density of $0.3W/cm^2$ at $750^{\circ}C$.

• Transactions of the Korean hydrogen and new energy society
• /
• v.16 no.4
• /
• pp.372-378
• /
• 2005

Ni/YSZ ($Y_2O_3$-stabilized $ZrO_2$) composite powder for a cathode material in high temperature electrolysis(HTE) was synthesized by a mechanical alloying method with Ni and YSZ powder. Microstructure of the composite and cell thickness for HTE reaction has been analyzed with various techniques of XRD, SEM to investigate effects of fabrication conditions. Employing the composite material, furthermore, the unit cell for HTE has been studied to evolve hydrogen from water. XRD patterns showed that the composites after wet mechanical alloying were composed of respective nano-sized crystalline Ni and YSZ. While ethanol as additive for mechanical alloying increased to $20\;{\mu}m$ of average particle size of the composites, alpha-terpineol effectively decreased to sub-micro size of that. This study has been found out the evolution of hydrogen by HTE reaction employing the fabricated cathode material, showing 1.4 ml/min of $H_2$ generation rate as increasing $20\;{\mu}m$ of cathode thickness.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.10a
• /
• pp.139-141
• /
• 2003

Multiple CeO$_2$/YSZ/Y$_2$O$_3$buffer layers, and subsequent YBCO films were deposited on the biaxially textured pure Ni and Ni ＋ 3at％W substrates using pulsed laser deposition. The deposition conditions of buffer layers on Ni and NiW were studied and compared. Good biaxial textures of buffer layers have been obtained on both substrates. The Jc's of YBCO films on these metal substrates were greater than 1$\times$10$^{6}$ A/$\textrm{cm}^2$ at 77K, 0T.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2000.04a
• /
• pp.41.2-41.2
• /
• 2000

• Proceedings of the Korean Ceranic Society Conference
• /
• 2003.04a
• /
• pp.130.2-130
• /
• 2003

• Proceedings of the Korean Ceranic Society Conference
• /
• 2003.04a
• /
• pp.47.1-47
• /
• 2003

• Proceedings of the Korean Ceranic Society Conference
• /
• 2003.10a
• /
• pp.70.2-70
• /
• 2003

• Proceedings of the KIEE Conference
• /
• 1995.11a
• /
• pp.404-405
• /
• 1995

Solid Oxide Fuel Cell has advantage of high utility because of having high operation temperature. In case of anode, Ni and YSZ being widly used as anode start materials. But Ni can be sintered during operation because that its operation temperature is very high, so it cause to lower the cell performance. It is very important to control the ratio of Ni to YSZ. In this paper, we studed on characterization of anode by controlling the Ni-YSZ contents.