• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 추계학술대회 논문집
• /
• pp.294-301
• /
• 2008

At the neutral sections, There are neutral sections inserted in overhead contact line between the substations to divide different phase current sections of AC electrified lines. Except convention line, a large stress occurs in the contact wire near the fittings under passing pantographs. So, in order to raise the train speed over 150km/h, a new type section has been adopted.

• 한국도로학회논문집
• /
• 제8권2호
• /
• pp.75-85
• /
• 2006

현재 우리나라 2차로도로 횡단면 설계기준은 설계속도별 최소 차로폭과 길어깨 기준은 있으나, 다양한 횡단면 구성안이 없어 전국이 획일적인 도로구조 형태를 보이고 있다. 따라서 본 연구에서는 2차로도로의 사고유형별 원인을 규명하고 그에 따른 교통운영 및 안전성 측면에서 횡단면 개선 방안을 수립하고, 평가척도를 선정하였으며, 평가과정을 통해 새로운 횡단면 설계기준을 제시하고 이를 검증하였다. 연구결과 같은 2차로도 도로폭 $9{\sim}12.9m$ 보다 $6{\sim}8.9m$ 도로가 사고율이 매우 높은 것으로 나타났으며, 대표적 사고유형들의 개선점은 차로 및 길어깨 확장으로 나타났다. 시뮬레이션 결과 도로폭 6$\sim$7m 는 교통량 1,000vph에서 급격한 지체 시간 상승을 보이고 있으나. 도로폭 10$\sim$11.5m도로는 1.200vph에서 약간의 변화를 보였다. 이 결과(pcu/일)를 국도와 지방도 일평균교통량(대/일)분포와 비교분석 하여 다양한 횡단면 기준을 제시하였다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 가을 학술발표회 논문집(II)
• /
• pp.995-1000
• /
• 2000

Segmentally erected prestressed concrete box girder bridges have been widely used in Korean high speed railway. Segmental erection has been accomplished along the longitudinal direction and across the depth of cross section. The cross section is similar to a composite cross section, composed of old and new segments. Because these segments have different time-dependent creep and shrinkage properties, a stress redistribution takes place during the construction period. It is the main objective in this research to investigate this behavior. An actual bridge was instrumented with 96 vibrating wire embedded type strain gauges, 6 electronic type steel strain gauges, and 75 thermocouples. Two span continuous high speed railway bridge was selected. Two points of importance, such as the midpoint of the first span and the point of interior support, along the span of the girder were chosen to monitor the time dependent behaviors for an extended period of time. The data collection was starting just after concrete girder were cast and is still going on. According to the measured results, the strain distributions across the depth of the section at midspan and interior support were not continuous and the important redistribution of stresses takes place. Thus, rational design of prestressed concrete composite box girder bridges need.

• 한국지열·수열에너지학회논문집
• /
• 제17권1호
• /
• pp.23-32
• /
• 2021

Conventional wind power generators have limited installation sites due to low efficiency due to reverse resistance or high cut-in speed. To compensate for these problems, this study proposed another new type of tilting wind turbine. The key to this method is the structural design of a cylindrical cam with a guide groove that allows the blade to tilt. As the blade rotates by the cam, it tilts according to the angle. In the section that generates torque by receiving drag, the blade is made perpendicular to the wind. And it is a structure that creates a parallel state with the wind in the section where reverse resistance occurs. We prepared six types of cams considering the length of the section subject to drag, reverse resistance, tilting section. The performance was analyzed as the maximum value of the output, torque coefficient, and efficiency coefficient, which is indicated by setting different wind speed and low TSR.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1998년도 가을 학술발표회 논문집
• /
• pp.193-200
• /
• 1998

The precast prestressed concrete girders of I-type section are frequently employed to design the short-to-medium span bridge. However, its beam depth is greatly increased as its span length is increased over than about 30m. Therefore, the economic and aesthetic effectiveness are rapidly decreased in case of the span length over 30m. The purpose of this paper is to verify the structural safety on the new spliced two span bridge and analyze the variation of member forces and stress distribution according to the construction stages and time. The new spliced technique is performed by partial post tensioning and release in the U-type girders. The structural characteristics of this technique is the introduction of secondary moment to reduce the bending moment by self weight of precast U-type girders constructed in simply supported beam type. So, it is expected that the structural efficiency of this spliced bridge may be improved more than other techniques.

• Journal of Biosystems Engineering
• /
• 제29권3호
• /
• pp.225-232
• /
• 2004

A new type of garlic peeling chamber has been developed which separates and peels garlic cloves using high-Pressure water Jets. The cylindrically-shaped chamber was fabricated with stainless steel plate and has a number of drilled holes, which function as solid-stream spray nozzles, on its interior wall. The chamber was divided into upper and lower section so that water can be applied at different pressures from each section. Three chambers of similar design were tested to evaluate their performances according to various pressure levels. The strongest correlation was observed between the pressure difference(lower-upper) and the proportion of unseparated and completely-peeled garlic cloves. Hanji-type garlic required higher or pressure difference to separate cloves from garlic bulbs than nanji-type garlic. On the other hand, protective leaves(skin) from the cloves were peeled more easily in case of hanji-type garlic. As a result of three consecutive peeling operations, the proportion of completely-peeled garlic cloves changed in the order of 80.1, 82.6, 84.1% in case of hanji-type, and 19.6, 29.1, 40.2% in case of nanji-type garlic.

• Steel and Composite Structures
• /
• 제21권3호
• /
• pp.537-551
• /
• 2016

A new type of composite beam which consists of a wide flange steel shape beam and an innovative type of composite slab was introduced. The composite slab is composed of concrete slab and normal flat steel plates, which are connected by perfobond shear connectors (PBL shear connectors). This paper describes experiments of two large-scale specimens of that composite beam. Both specimens were loaded at two symmetric points for 4-point loading status, and mechanical behaviors under hogging and sagging bending moments were investigated respectively. During the experiments, the crack patterns, failure modes, failure mechanism and ultimate bending capacity of composite beam specimens were investigated, and the strains of concrete and flat steel plate as well as steel shapes were measured and recorded. As shown from the experimental results, composite actions were fully developed between the steel shape and the composite slab, this new type of composite beams was found to have good mechanical performance both under hogging and sagging bending moment with high bending capacity, substantial flexure rigidity and good ductility. It was further shown that the plane-section assumption was verified. Moreover, a design procedure including calculation methods of bending capacity of this new type of composite beam was studied and proposed based on the experimental results, and the calculation methods based on the plane-section assumption and plastic theories were also verified by comparisons of the calculated results and experimental results, which were agreed with each other.

• 한국해안·해양공학회논문집
• /
• 제22권1호
• /
• pp.1-9
• /
• 2010

말뚝 상부에서 수평력 대부분을 저항한다는 매커니즘을 활용하여, 횡방향 하중이 대부분인 항만 및 해양구조물에 효율적으로 적용할 수 있는 새로운 말뚝 형식을 고안하였다. 이번 연구에서는 버켓 기초식 보강기법, 팽이 기초식 보강기법, 그라우팅식 보강기법 등 3가지 형태의 보강기법을 활용한 상부 확대형 횡방향 지지 증대 말뚝에 대한 3차원 유한요소해석을 수행하였다. 이를 통해 지반의 종류를 비롯하여, 각 보강 기법의 종류, 말뚝의 종류 및 길이, 지반의 심도 등 다양한 변수가 말뚝의 횡방향 지지 거동에 미치는 영향을 검토하였다. 해석 결과, 버켓 기초를 활용한 경우 팽이기초나 그라우팅 기법 등 전반적으로 다른 보강기법을 활용한 경우에 비해 횡방향 지지력 효율이 상대적으로 가장 뛰어난 것으로 나타난다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 춘계학술대회 논문집
• /
• pp.31-34
• /
• 2004

A new extrusion process of the circular section product with helical fins could be developed by using rotating extrusion dies. The twisting of extruded product is caused by the twisted conical die surface connecting the die entrance section and the die exit section linearly. But, until now, because the process has used fixed extrusion dies, it needs high pressure in order to twist billet and form fin shape on the surface of billet. So, during extruding billet, in order not to twist billet, the extrusion dies is needed to rotate itself instead of twisting billet. And in order to rotate dies, the shape of inside contour of extrusion dies must have conical type with twisted Inclined die surface connecting the die entrance section and the die exit section linearly. The results of experiments show that, in spite of using twisted extrusion dies, twisting of the billet should not happen because of rotating dies in the opposite direction of twisting direction of billet during extruding billet, and, from the results, it shows that it can decrease the power of extrusion pressure and could prevent crack of teeth for fin forming.

• 대한조선학회논문집
• /
• 제34권1호
• /
• pp.11-23
• /
• 1997

본 논문은 선박용 프로펠러 날개단면의 개발 과정을 다루고 있다. 2차원 날개단면의 유체역학적 특성은 캠버 및 두께 분포, 앞날 반경 등 기하학적 형상에 따라 달라진다. 2차원 날개단면 주위의 전 유장을 난류로 고려한 후 해석하기 위해 유한 체적법에 의한 Reynoles time averaged Navier-Stockes 방정식을 이용한 수치해석 기법을 개발하였다. 본 연구에서는 날개단aus 표면에 보다 많은 계산점을 주면서도 받음각의 변화에도 격자계 생성이 용이한 O-Type 격자계를 채택하였고, 전 유동장은 k-${\varepsilon}$ 난류 모형을 적용하여 해석하였다. 본 연구에서 개발된 수치해석 기법은 NACA0012의 실험 결과와 비교하여 계산 정도를 확인하였다. 본 연구에서는 낮은 항력을 갖는 고효율 날개단면 개발을 목표로, 항력이 양호한 날개단면은 공동 터널에서 양력, 항력 및 공동 특성 실험을 수행하였으며, 수치 해석 결과와도 비교하였다. 본 연구를 통하여 개발된 2차원 날개단면 해석용 수치 유체역학 코드는 실험 결과와 잘 일치하고 있음을 알 수 있었다. 이상의 과정을 통하여 기존의의 날개단면인 NACA66 두께 분포와 a=0.8 mean line 캠버를 갖는 KH13보다 효율뿐만 아니라 공동 특성도 우수한 단면인 KH28을 개발할 수 있었다. 새로운 날개 단면인 KH28은 선박용 프로펠러에 적용하기 위한 연구가 지속되어야 하며, 한편 낮은 받음각에서 양-항력 추정의 정확도를 높이기 위해서는 개발된 수치해석 코드에 2-경계층 모형이 적용되어야 할 것으로 본다.