• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.33 no.4
• /
• pp.275-284
• /
• 1997

This experiment was carried out to measure the sinking depth of each buoy, the change in the net shape of the net, and the tension of sand bag line according to the R (from bag net to the fish court) and L (from fish court to the bag net) current directions and their velocity by the model experiment. The model net was one-fiftieth of the real net, and its size was determined after considering the Tauti’s Similarity Law and the dimension of the experimental tank. 1. The changes of the net shape were as follows : In the current R, the end net of fish court moved 20mm down the lowerward tide and 10mm upper part. So the whole model net moved up at 0.2m/sec. The shape of the net showed an almost linear state from bag net to the fish court at 0.6m/sec. In the current L, the door net moved 242mm down the lowerward tide and 18mm upper part. So the whole model net moved up at 0.2m/sec. The net shape showed an almost linear state from the fish court to the bag net at 0.5m/sec. 2. The sinking depths of each buoy were as follows: In the current R, the head buoy started sinking at 0.2m/sec and sank 20mm, 99mm at 0.3m/sec and 0.6m/sec, respectively. The end buoy didn't sink from 0m/sec to 0.6m/sec but showed a slight quake. In the current L, the end buoy started sinking at 0.1m/sec, and sank 5mm and 108mm at 0.2m/sec and 0.6m/sec, respectively. The whole model net sank at 0.5m/sec except the head buoy. 3. The changes of the sand bag line tension were as follows: In the current R, the tension affected by the sand bag line of the head buoy showed 273.51g at 0.1m/sec increased to 1298.40g at 0.6m/sec. In the current L, the tension affected by the sand bag line of the end buoy on one side showed 137.08g at 0.1m/sec increased to 646.00g at 0.6m/sec. The changes in the sand bag line tension were concentrated on the sand bag line of the upperward tide with increasing velocity at the R and L current directions. However, no significant increase in tension was observed in the other sand bag lines.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.12
• /
• pp.1325-1333
• /
• 2014

The dispersion pattern of a near miss neutralizer has a great effect on the disablement of a threatening projectile. This study numerically investigated the dispersion pattern of cylindrical tungsten impactors by an explosion in the near miss neutralizer. The mass and shape of the explosive were considered as influencing factors on the dispersion pattern. The explosives were set using two shape models: a parallel shape with the same upper and lower thicknesses and a tapered shape with different upper and lower thicknesses. In the simulation results, the dispersed impactors formed a ring-shaped pattern on a two-dimensional plane in an arbitrary space. In addition, the fire net area increased with the explosive mass when the explosive shapes were identical. In particular, the tapered shape explosive formed a larger fire net area than the parallel shape explosive. Based on the analysis of the fire net area along with the dispersion density, both the explosive mass and shape representing the physical characteristics should be considered for controlling the dispersion pattern of impactors in a near miss neutralizer.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.3
• /
• pp.147-156
• /
• 2008

A new approach based on cone prism intersection method combined with sorting algorithm is proposed for the fast and robust signed distance field computation. In the method, the space bounding the geometric model composed of triangular net is divided into multiple smaller cells. For the efficient calculation of distance fields, valid points among the triangular net which will generate minimum distances with current cell are selected by checking the intersection between current cell and cone prism generated at each point. The method is simple to implement and able to achieve an order of magnitude improvement in the computation time as compared to earlier approaches. Further the method is robust in handling the traditional sign problems. The validity of the suggested method was demonstrated by providing numerous examples including Boolean operation, shape deformation and morphing of complex geometric models.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.2 s.173
• /
• pp.526-534
• /
• 2000

Near-net-shape forming of zirconia powder was investigated under the combination of cold die and isostatic pressing and pressureless sintering. A novel combination pressing technique, i.e., die com paction under cold isostatic pressing, allowed to produce a complex shaped ceramic powder compact with the controlled dimensions and relatively uniform density distributions. The constitutive models proposed by Kim and co-workers for densification of ceramic powder under cold compaction and high temperature were implemented into a finite element program (ABAQUS). Experimental data for relative density distributions and deformations of zirconia powder compacts produced by cold combination pressing and pressureless sintering were compared with finite element results. Finite element results agreed well with experimental data.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.15 no.3
• /
• pp.28-35
• /
• 2016

Forging operations are non-stationary processes occurring because of indirect pressure, generally, under conditions of three-dimensional stress and deformation. Furthermore, due to friction and the constraints of die geometry, deformation is not homogeneous. Material flow and deformation are largely determined by the shape of the tools. It is well known that net-shape forging can improve the mechanical strength of the final product as well as reduce material waste. Oxygen-free copper that is used for electrical and electronic components has excellent electrical and thermal conductivity. Oxygen-free copper parts have a low productivity in cutting process. Thus, the forging process is performed in order to improve the low productivity in cutting process. The forging of oxygen-free copper for electrode body parts was modeled using finite element simulation and forging experiments that were conducted for producing electrode body parts at room temperature. In order to reduce the cost of cutting products, the forging was performed in a closed cavity to obtain near-net or net-shape parts.

• Journal of the Korean Society for Heat Treatment
• /
• v.14 no.3
• /
• pp.155-159
• /
• 2001

The thermal shock resistance has been investigated and compared in three hot-work tool steels. The resistance to thermal shock is first of all a matter of good toughness and ductility. Therefore, a proper hot-work tool steel should be characterized by high fracture strength and high temperature toughness. In this study, new test method is proposed to measure the thermal shock resistance. New method is basically based on Uddeholm' thermal shock test but some modification has been properly applied. Based on these results, some critical temperature($T_{fractures}$) at which fracture occur can be measured to characterize the thermal resistance of the materials. The specific values of ${\Delta}T$, the temperature difference between holding temperature and $T_{fractures}$, has been successfully used as a measure of the thermal shock resistance in this study, the results showed that the thermal shock method used in this study was properly modified.

• Korean Journal of Materials Research
• /
• v.13 no.1
• /
• pp.64-68
• /
• 2003

The 1.6 vol% and 2.5 vol% TiNi/6061Al composites were fabricated by permanent mold casting for investigating the effect of heat treatment on tensile strength for composites. The tensile strength without T6 treatment at 293 K was increased with increasing the volume fraction of TiNi fiber and at 363 K the higher the pre-strain, the higher the tensile strength. The tensile strength of the composite with $T_{6}$ treatment at 293 K was found to increase with increasing both the amount of pre-strain and the volume fraction of TiNi fiber and was higher than that without $T_{6}$ treatment. It should be noted that the tensile strength 2.5vol%TiNi/6061Al composites rolled at a 38% reduction ratio was the maximum value of 298 MPa. The tensile strength of composites decreased with increasing the reduction ratio over 38% because of the rupture of TiNi fiber.

• Journal of Korea Foundry Society
• /
• v.26 no.2
• /
• pp.98-103
• /
• 2006

Metal-mold reactions between investment mold and TiAl alloys were investigated for the economic net-shape forming of TiAl alloys. The effect of mold preheating temperatures on the metal-mold reaction were investigated using a vacuum induction-melting furnace. In the case of TiAl alloys, there were no ${\alpha}$-case formation reactions. There were neither interstitial nor substitutional ${\alpha}$-case formations as TiAl alloys have both negligible solubility of oxygen and low activity in molten states. The fluidity of TiAl alloys increases with mold preheating temperature since they have a peritectic reaction that appears in the form of envelope, surrounding each particles of the primary constituent. The results of the investment casting of TiAl alloys confirm that the casting route in our study can be an effective approach for the economic net-shape forming of TiAl alloys.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.10a
• /
• pp.173-176
• /
• 2007

The characteristics of the tool system give many effects into the costs and qualities for the finished components. This study proposes a new method for manufacturing of high manufacturing productivity, production process reduction and low cost through back pressure forming. The Lock-up hub is manufactured through many processes, such as upsetting($1^{st}$ Forming), piercing, direct extrusion($2^{nd}$ Forming), final sizing process($3^{rd}$ Forming). In this study, process design for closed-die forging of a Lock-up hub used for a component of automobile transmission was made using three-dimensional finite element simulations, and the strain distributions and velocity distributions are investigated through the post processor. The rigid-plastic finite-element method for back pressure forging has been used in order to reduce development time and die cost. Using the FEM simulation, we found the optimum value of back pressure. The prototypes of Lock-up hub parts were forged into the net-shape. In the experiment, lead precision of tooth are measured by the CCMM(Contact Coordinate Measuring Machine). The dimensional accuracy of forged part was improved up to the 40% when back press was applied.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.36 no.4
• /
• pp.287-298
• /
• 2000

The charge of distance and the change of tack between paired boats were measured by ship's distance measuring system fixed MCS in the main boat and MS in the following boat. The operating depth of the anchovy boat seine was recorded and analysed by self memory temperature/depth sensor in order to compare the relationship between the distance between towing boats and geometry of the anchovy boat seine net. The results are as follow, (1) When distance between paired boat was 5m, the fishing net was spreaded down deeply and unstably in accordance with bag net and flapper may be help to pass out anchovy school. (2) When distance between paired boat was 100m, vertical opening of the net was gradually increased with higher slope of towing depth in the square, bosom and flapper. Therefore, fishing efficiency could be decreased by preventing the entering of anchovy due to unstable shape of the bag net. (3) When distance between paired boat was 200m, the geometry of the anchovy seine was stable condition with the end of bag net was up while flapper was down and it may cause bad effect in fishing efficiency. (4) When distance between paired boat was 300m, the shape from wing net to bag net was gradually slow down and stable enough as well as good shape in bag net and flapper. (5) The ship's distance measuring system could be used for measurement and accurate control of distance between paired boat in accordance of anchovy recordings by fish finder in order to get higher fishing efficiency in anchory boat seine operation.