• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2010.05a
• /
• pp.229-230
• /
• 2010

The Carbonation, one of the main deterioration factors of concrete, reduces capacity of members with providing rebar corrosion environment. Consequently it suggested standards of all countries of world, carbonation depth prediction equation of respective researchers and time to rebar corrosion initiation. As a result of carbonation depth prediction equation calculation, difference of time to rebar corrosion initiation is 149 years and difference of carbonation depth prediction equation is 162 years when water cement ratio is 50%. So a study on rebar corrosion with carbonation depth will need existing reliable data and verifications by experiment.

• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.743-746
• /
• 2002

Experimental investigation of the flow field of supersonic cavity is described. In this research, supersonic cavity is used in chemical laser system. For efficient laser, downstream flow after cavity need to be uniform and clear for pressure recovery system. In previous research, it's known that there's oscillation In cavity and is due to Mach number and L/D ratio. A strong recompression occurs at the after wall and the flow is visibly unsteady. Cavity flow in this research is of the open type, that is, length-to-depth ratio $L/D<10\;at\;M\;=\;3$. Experiment is done with pressure measurement by piezo-type sensor and visualization by Schlirern method. The time-dependent experimental result is compared with computation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.1063-1067
• /
• 1997

A study of carbide step drill cutting ability is highly progessing the step drill with more then twice diameter rate is so difficult in regrinding and very easy to damage during machining. As the machining of step drill for closed hole is occur to breakage at small diamter poistion, so it is very difficult to machinine. Thue, in this experiment, We investance roundness and surface roghness by machining distance and were identifid that the first distance, 5~10m, was fine with 7 .mu.m but the arround of 15m was happened so much alternation. And we were indentified that after 20m was happend statable machining. The surface roughness was happened the same conditions. So application of stwp drill we think that the selection of cutting conditions need lots consideration and the study of step drill's diameter ratio ratio is carred out.

• Proceedings of the KSPS conference
• /
• 2005.04a
• /
• pp.99-102
• /
• 2005

Research efforts have been made for out-of-vocabulary word rejection to improve the confidence of speech recognition systems. However, little attention has been paid to non-recognition sentence rejection. According to the appearance of pronunciation correction systems using speech recognition technology, it is needed to reject non-recognition sentences to provide users with more accurate and robust results. In this paper, we introduce standard phoneme based sentence rejection system with no need of special filler models. Instead we used word spotting ratio to determine whether input sentences would be accepted or rejected. Experimental results show that we can achieve comparable performance using only standard phoneme based recognition network in terms of the average of FRR and FAR.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.9
• /
• pp.713-719
• /
• 2008

Most of the MEMS parts are made of multi-grain silicon wafer, which is the orthotropic material and its material direction is arbitrary. The reliability of the parts must be guaranteed in order to use for the commercial usage. The need of the structural analysis of its parts emerges an important factor. The material properties of the MEMS parts are calculated by the numerical method in order to reduce a material test. In this study, the effective elastic modulus and its Poisson's ratio are calculated by the boundary element method(BEM) and are compared with the results by the finite element method(FEM).

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.1918-1923
• /
• 2010

In electic railway, 25kV is applied to AC sections of overhead contact lines and pantographs of Korea Train eXpress(KTX) make contact at speeds of 300km/h. Thus, there is a need to utilize wireless, optic, contact-less sensors to implement condition monitoring systems. This paper is based on describing and analyzing the condition monitoring system implementation technologies for efficient catenary current ratio characteristic assessment. The conclusion of this paper should be widely applied to design, diagnosis, completion of construction, current collection status, fault diagnosis, and selection of contact wires and suspension wires.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1993.12a
• /
• pp.85-91
• /
• 1993

Air-Lubricated tilting pad journal bearing that has high stability is analyzed by using the direct method, and this bearing is usually used to need high precision. The pressure that supports the shaft is occured by the differences between the shaft and pads radii of curvatures. So the characteristics of load capacity for their variable values is important. In this paper the load capacity is compared with some of the eccentricity ratio values. The large load oapacity comes form large eccentricity ratio, high bearing number and high preload. But if the preload becomes too high, the shaft comes into contact with the pads. Stiffness and damping coefficients are compared with some of the preload, too. The coefficients decreased along compressibility number with constant load.

• Journal of the Korea Concrete Institute
• /
• v.12 no.4
• /
• pp.59-67
• /
• 2000

With increased height of structure, the effect of column shortening need special consideration in the design and construction of high-rise buildings. The shortening of each column affects nonstructural members such as partitions, cladding, and M/E systems, which are not designed to carry gravity forces. The slabs and beams will tilt due to the cumulative differential shortening of adeacent vertical members. The main purpose of estimating the total shortening of vertical structural member is to compensate the differential shortening between adeacent members. This paper presents effect of parameters for phenomenon of column shortening in vertical members. The paper presents effect of parameters for phenomenon of column shortening in vertical members. The conclusions obtained from this study are follow as ; Strength of concrete and steel ratio effected on column shortening caused by elastic and inelastic shortening. Also, it is known that Ultimate-shrinkage-Value, Specific-Creep-Value, and volume to surface ratio effected on inelastic shortening only. Particularly, Ultimate-Shrinkage-Value and Specific-Creep-Value effected considerable on the amount of total column shortening.

• International journal of advanced smart convergence
• /
• v.9 no.2
• /
• pp.123-128
• /
• 2020

We constructed a cooling system for solar cells using convection phenomena and investigated its cooling performance. The cooling system didn't need any driving power or water resources. The convection cooler manufactured with a right-triangle shape of an air duct was attached to the rear of the solar cell to confirm that cooling was performed using convection phenomena. When the ratio of duct width to attachment surface width was 3:7, and the ratio of entrance height and exit height of duct was 5:1, it showed the best cooling performance. Comparative experiments with solar cells without convection cooler showed that cooling effects from 16.5℃ to 20.9℃ occurred after 40 minutes exposed to the 1300W Xenon lamp condition.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.12
• /
• pp.2505-2510
• /
• 2009

Semiconductor processes need measurement to confirm where there are problems in quality after progresses manufacturing process. This paper suggests equipment and automatic measure sampling method that control monitoring ratio according to change point occurrence availability of process that is not measure method by the existent simple ratio rate. This paper defines measure section as ailment section, metastable section and stability section by change point standard and create statistical model of each section and developed suitable measure rate model by section. As a result, we have accomplished maximum throughput and minimum sampling number that needs to maintain constant level of quality. Proposed method minimizes load of measure process by brings production quality sophistication and decrease of process badness and lowers measure rate in stable section making perception about problem occurrence quick heightening measure rate at change point occurrence.