• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.187-189
• /
• 2007

• Laser Solutions
• /
• v.3 no.3
• /
• pp.31-37
• /
• 2000

In this paper, the possibilities of the laser overlap spot welding were studied to utilize the advantageous properties of amorphous metal foils. In order to estimate the usage of amorphous metals foils as structural members, the tensile shear strength and the fracture features were investigated. Although the crystalline zone on the surface was formed, it was not the direct cause of the fracture of the weld. The fracture of the weld resulted from the geometry discontinuity between the workpiece and the protrusion zone, which was formed during the weld process. The vein pattern - the typical feature of the fracture of the amorphous metal - was formed on the fracture surface. The tensile shear stress was reached to 1200 N/㎟ (2-foils overlap welding) and 900 N/㎟ (10-foils overlap welding), whereas the tensile strength of the workpiece was 1500-2000 N/㎟.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.932-935
• /
• 2005

Three dimensional laser welding technology for light car body is studied. A robot, a seam tracking system and 4kW CW Nd:YAG laser are used for three dimensional robot laser welding system. The Laser system is used 4kW Nd:YAG laser(HL4006D) of Trumpf and the Robot system is used IRB6400R of ABB. The Seam tracking system is SMRT-20LS of ServoRobot. The welding joint of steel plate are butt and lap joint. The 3-D welding for Non-linear Tailored blank is performed after the observation experiments of bead on plate. Finally, the welding process for non-linear tailored blank and front side member is developed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.17-18
• /
• 2006

Laser welding of metals has been widely used to improve a wear resistance and a corrosion resistance of the industrial parts. The objective of this research works is to investigate the influence of the process parameters, such as the welding for metals with CW Nd:YAG lasers. The bead-on-plate welding tests are carried out for several combinations of the experimental conditions. In order to quantitatively examine the characteristics of the butt welding, the welding quality of the cut section, stain-stress behavior and the hardness of the welded part are investigated. From the results of the investigation, it has been shown that the optimal welding condition without defects in the vicinity of the welded area and with a good welding quality is 1400W of the laser power, 0.8m/min, 0.9m/min of welding speed and $4{\ell}$ in of pressure for shielding gas.

• Journal of Welding and Joining
• /
• v.18 no.3
• /
• pp.83-88
• /
• 2000

Laser cladding processing allows rapid transfer of heat to the material being processed with minimum conduction into base metal, resulting in low total heat input. The effects of Nd:YAG laser cladding with wire feeding on the mechanical properties of Inconel alloy were investigated. inconel alloy is used as the material of nuclear steam generator tubing because of its mechanical properties and corrosion resistance properties. The device for Nd:YAG laser cladding with wire feeding was designed. It consists of the wire feeding system, the wire cladding system and the shielding gas system which prevents the clad layer from being oxidized. Experimental as results indicated that the wire feeding direction and position were important for laser cladding with wire feeding. The wire feeding speed should be adapted according to cladding speed for good shaping of clad layer. The effect of heat on the HAZ size can be limited and the growth of grain size of HAZ size was not serious. The hardness of clad layer and heat affected zone increased with increasing of cladding speed.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.3 s.180
• /
• pp.47-55
• /
• 2006

Laser welding of dissimilar metals has been widely used to improve a wear resistance and a corrosion resistance of the industrial parts. The objective of this research is to investigate the influence of the process parameters, such as the welding for SM45C and STS304 with CW Nd:YAG lasers. The bead-on-plate welding tests are carried out for several combinations of the experimental conditions. In order to quantitatively examine the characteristics of the dissimilar welding, the welding quality of the cut section, stress-strain behavior and the hardness of the welded metal are investigated. From the results of the investigation, it has been shown that the optimal voiding condition without defects in the vicinity of the welded area and with a good welding quality is 1600W of the laser power, 0.85m/min of welding speed and $4{\ell}/min$ of pressure for shielding gas.

• Laser Solutions
• /
• v.10 no.3
• /
• pp.25-32
• /
• 2007

The effect of welding speed on the weldability, microstructures, hardness, tensile property of Nd:YAG laser welding joint in 600MPa grade precipitation hardening high strength steel was investigated. A shielding gas was not used, and bead-on-plate welding was performed using various welding speeds at a power of 3.5kW. Porosity in the joints occurred at 1.8m/min, but were not observed over the welding speed of 2.1m/min. However, spatter occurred over the welding speed of 6.6m/min. The hardness was the highest at heat affected zone(HAZ) near fusion zone(FZ), and was decreased on approaching to the base metal. The maximum hardness increased with increasing welding speed. The microstructure of FZ was composed of coarse grain boundary ferrite and bainite(upper) but the HAZ near the FZ contained bainite(Lower) and fine ferrite at a low welding speed. With increasing welding speed, ferrite at the FZ and the HAZ became finely and upper binite changed to lower bainite. In a perpendicular tensile test to the weld line, all specimens were fractured at the base metal, and the tensile strength and the yield strength of joints was equal to those of raw material. Elongation was found to be lower than that of the raw material.

• Proceedings of the KWS Conference
• /
• 1997.10a
• /
• pp.262-264
• /
• 1997

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.1
• /
• pp.99-104
• /
• 2010

Magnesium and magnesium alloys, the lightest structural materials, have been received plenty of global attention recently. These alloys could be applied in various fields, especially the electronics industry, because of their excellent electromagnetic interference shielding. However, the welding technique of magnesium alloys has not been established. This study is related to the welding of AZ31B magnesium alloy by a short-pulsed a Nd:YAG laser. Two types of pulse waves, square pulse and variable pulse, were used to control weld defects. Results show that the crack and porosity, generated in the weld, had not been controlled by general square pulse. But through the application of variable pulse, the defects could be prevented and the good weld zone was obtained.

• Journal of Welding and Joining
• /
• v.17 no.1
• /
• pp.71-76
• /
• 1999

The real-time holographic interferometer with digital high-speed camera is applied to the experimental study of laser induced plasma/plume in pulsed Nd:YAG laser welding. A pulsed Nd:YAG laser with 1.2 kW average power is applied to generate laser induced plume. The recording speed of the high-speed camera is 3,000 f/s. The high speed photographs of weld plume without another visualization method, are compared with the visualization photographs with holographic interferometer. The radiation intensity from the laser induced plume is recorded by the high speed photographs, which fluctuated during laser radiation and disappeared after laser end. The density distribution of the plume is recorded by the holographic visualization method. The experimental results show the process of generation of the laser induced plasma/plume, and give the feasibility of quantitative measurement of laser induced plume in laser welding.